Commit graph

74 commits

Author SHA1 Message Date
Chris Kuethe
1005ccda97 patch - arm - define SYS_CACHELINE_SIZE for mx5
mx5 is a cortex-a8 which has 64 byte cache lines. i'll need this for
adding gadget support to usbarmory, but it's a property common the the
entire SoC family - may as well make it available to all MX5 boards

Works on usbarmory; compile-tested on mx53loco and mx51_efikamx too

Signed-off-by: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Matthew Starr <mstarr@hedonline.com>
Cc: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-06-09 12:00:42 +02:00
Stefano Babic
32df39c741 mx5: fix get_reset_cause
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.

Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
2015-03-05 10:29:27 +01:00
Fabio Estevam
32c81ea65c imx: consolidate set_chipselect_size function
Move MX5 specific set_chipselect_size function into generic i.MX part,
such that MX6 based boards are able to use this function as well.

While doing this the iomuxc gpr member needed to be consolidated between
MX5 and MX6.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20 10:30:19 +01:00
Marek Vasut
68968901e7 ARM: mx5: Fix CHSCCDR name
Fix the name of the CCM CHSCCDR register.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-08-20 12:19:20 +02:00
Masahiro Yamada
9f2ec3f543 spl: consolidate arch/arm/include/asm/arch-*/spl.h
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.

But many of them just define BOOT_DEVICE_* macros.

Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.

So they should not be archtecture specific, but be described as
a simpile enumeration.

This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.

With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
2014-06-06 10:05:34 +02:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Markus Niebel
d7cbcc762e spi: spi-mxc: add defines for clk inactive state for ECSPI
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:29:26 +05:30
Fabio Estevam
6a99f03d69 imx: Introduce a header for the imx cpu versions
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-02-11 11:24:11 +01:00
Sergey Alyoshin
4611d5bab2 arm: mx5: Add fuse supply enable in fsl_iim
Enable fuse supply before fuse programming and disable after.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-03 15:44:06 +01:00
Fabio Estevam
76b6b19614 usb: ehci-mx5: Use 'bool' instead of 'unsigned char'
The 'enable' argument can be better expressed as boolean.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-26 21:56:34 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Benoît Thébaudeau
ba5dfc11ba imx: mx5: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2013-05-05 17:55:05 +02:00
Benoît Thébaudeau
3d53fc9450 imx: iomux-v3: Add iomux-mx53.h
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX53. The content of the file is taken from Freescale's Linux kernel at
commit 4ab3715, plus the required changes to make it work in U-Boot.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:04 +02:00
Benoît Thébaudeau
f54326d17d imx: iomux-v3: Add missing definitions to iomux-mx51.h
Add missing definitions that are required by future changes.

By the way, make some cosmetic cleanup.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:04 +02:00
Benoît Thébaudeau
f49d92a35b imx: iomux-mx51: Fix MX51_PAD_EIM_CS2__GPIO2_27
In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename
MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:04 +02:00
Marek Vasut
f399f63647 arm: mx5: Add NAND clock handling
Augment the MX5 clock code with function to enable and configure
NFC clock. This is necessary to get NFC working on MX5.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-05-05 17:45:05 +02:00
Marek Vasut
cfb8e87a8e arm: mx5: Add SPL support code to MX5
Fix minor adjustments needed to get SPL framework building on MX5.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-05-05 17:45:05 +02:00
Benoît Thébaudeau
7e2173cf82 imx: iomux-v3: Include PKE and PUE to pad control pull definitions
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.

By the way, remove some unused pad control definitions.

There is no change of behavior.

Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28 11:15:07 +02:00
Benoît Thébaudeau
d73b97604b imx: iomux-v3: Fix common pad control definitions
Commit dc88403 "iomux-v3: Place pad control definitions into common file" broke
mx51_efikamx because it made i.MX6's pad control definitions conflict with
i.MX51's.

i.MX51's pad control definitions are actually common to some other i.MX
(25/35/53), so move them to the common iomux-v3.h (just like what is done in
Linux's), and select the correct definitions depending on whether CONFIG_MX6 is
defined or not.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28 11:15:06 +02:00
Benoît Thébaudeau
6adbd30203 imx: Add useful fuse definitions
Define the UID (SoC unique ID) fuses, and the fuses available for the user.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28 11:07:40 +02:00
Benoît Thébaudeau
8f3ff11c1f imx: Homogenize and fix fuse register definitions
IIM:
 - Homogenize prg_p naming (the reference manuals are not always self-consistent
   for that).
 - Add missing SCSx and bank registers.
 - Fix the number of banks on i.MX53.

OCOTP:
 - Rename iim to ocotp in order to avoid confusion.
 - Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
   reference manual.
 - Merge the existing spinoff gp1 fuse definition on i.MX6.
 - Fix the number of banks on i.MX6.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-04-28 11:07:40 +02:00
Fabio Estevam
1155d555d6 mx53ard: Move register masks into imx-regs.h
imx-regs.h is more appropriate location for containing register masks.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-04-25 21:48:21 +02:00
Fabio Estevam
0f1411bc8d spi: mxc_spi: Set master mode for all channels
The glitch in the SPI clock line, which commit 3cea335c34 (spi: mxc_spi: Fix spi
clock glitch durant reset) solved, is back now and itwas re-introduced by
commit d36b39bf0d (spi: mxc_spi: Fix ECSPI reset handling).

Actually the glitch is happening due to always toggling between slave mode
and master mode by configuring the CHANNEL_MODE bits in this reset function.

Since the spi driver only supports master mode, set the mode for all channels
always to master mode in order to have a stable, "glitch-free" SPI clock line.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-13 17:46:42 +02:00
Troy Kisky
abbab70363 mx31/mx35/mx51/mx53/mx6: add watchdog
Use a common watchdog driver for all these cpus.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-01-13 11:39:57 +01:00
Fabio Estevam
d84f56f48f mx5: Align SPI CS naming with i.MX53 reference manual
Align SPI chip select naming with i.MX53 reference manual.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-19 08:48:59 +01:00
Troy Kisky
eb0344d974 imx-common: cpu: add imx_ddr_size
Read memory setup registers to determine size
of available ram. This routine works for mx53/mx6x

I need this because when mx6solo called get_ram_size
with a too large maximum size, the system hanged.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10 08:15:40 +01:00
Troy Kisky
20332a066a mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite
Previously, the same value was returned for both mx6dl and mx6solo.
Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev
stored at 0x280 instead of 0x260.
I don't have a sololite to verify.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10 08:15:40 +01:00
Fabio Estevam
782b028841 mx5: lowlevel_init.S: Fix PLL settings for mx53
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz.

Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz
instead.

Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI
at 1080p because the IPU clock cannot reach the requested frequency.

Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its
maximum frequency.

Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little
bit to allow easier comparison with the original clock setup from FSL U-boot.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17 18:09:34 +02:00
Benoît Thébaudeau
323846561a mx5/6 clocks: Fix SDHC clocks
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although
they have dedicated clock paths.

Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must
be set accordingly. This is good for the case only a single SDHC instance is
used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix
the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
b94792982f mx5 clocks: Fix get_lp_apm()
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024.
In that case:
 - on i.MX51, this clock comes from the output of the FPM,
 - on i.MX53, this clock comes from the output of PLL4.

This patch fixes the code accordingly.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
649dc8abd9 mx5 clocks: Add and use CCSR definitions
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
414e1660c8 mx51: Fix USB PHY clocks
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.

The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
248cdf0b52 mx5: Fix clock gate values
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one
of these bits like what was done is wrong and can lead to unpredictable behavior
depending on the original value of these bit-fields.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
1f5e4ee0b9 mx5: Use explicit clock gate names
Use clock gate definitions having names showing clearly the gated clock instead
of names giving only a register field index.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
846b38981f mx5 clocks: Cleanup
Clean up the i.MX5 clock driver:
 - Use readl() and writel() instead of their __raw_ counterparts.
 - Use the clr/setbits_le32() family of macros rather than expanding code.
 - Use accessor macros for bit-fields instead of _MASK and _OFFSET.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
833b6435de mx5/6: Define default SoC input clock frequencies
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:10 -07:00
Matthias Weisser
e7bed5c2b3 imx: Use MXC_I2C_CLK in imx i2c driver
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
362635bd50 mx51evk: Add CONFIG_REVISION_TAG
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.

If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.

Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-09-23 19:55:06 +02:00
Benoît Thébaudeau
8e99ecd74b mxc: Define architecture identifier
Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.

The i.MX28 is omitted because its architecture is a bit different (like imx/mxc
vs. mxs in Linux).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
2012-09-01 14:58:30 +02:00
Matt Sealey
af369d9831 mx5: add iomux-mx51.h include
Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus the required changes to make it work in U-Boot.

The contained pad settings are the minimum required to make an Efika MX boot
and get all the currently-implemented peripherals working in U-Boot.

It is recommended that this file not be just a dumping ground for pins but
only contain the settings required for all the boards using it.

Changes for v2:
 * reference commit id from Linux kernel
 * additionally roll in the USB pads
 * removed GPIO_NUMBER define

Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:29 +02:00
Benoît Thébaudeau
4311c1ab6a mx5: Undeclare imx_decode_pll()
The imx_decode_pll() function does not exist for mx5, so remove its declaration.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:27 +02:00
Stefano Babic
5fecb36ca0 MX: Set a common gpio.h for all i.MX
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
2012-09-01 14:58:27 +02:00
Troy Kisky
124a06d7fb imx-common/cmd_bmode.c: add imx bmode (bootmode) command
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.

Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:26 +02:00
Troy Kisky
cc54a0f7cc imx-common: add i2c.c for bus recovery support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:57 +02:00
Troy Kisky
df369dcdb0 i.mx53: add definition for I2C3_BASE_ADDR
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:44 +02:00
Fabio Estevam
05d4df1d8a mx6: Allow mx6 to access the IPUv3 registers
Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-10 11:35:38 +02:00
Fabio Estevam
fff6ef72b3 mx53: Allow IPUv3 driver to also work on mx53
Adjust the IPU base registers so that ipuv3 driver can work on both mx51 and
mx53 SoCs.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-25 10:36:29 +02:00
Stefano Babic
c4559daa91 MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
After an update to the MX51 reference manual (Rev. 5), the
values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH
are now clearly wrong:

"Bit 13:
High / Low Output Voltage Range. This bit selects the output voltage mode for
SD2_CMD. 0 High output voltage mode
1 Low output voltage mode"

The values are currently negated in code - fixed.

Reported-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: David Jander <david.jander@protonic.nl>
Acked-by: David Jander <david.jander@protonic.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:35 +02:00
Fabio Estevam
54cd1dee8f mx53loco: Add CONFIG_REVISION_TAG
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.

The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.

Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Fabio Estevam
1fc56f1cb0 mx53loco: Allow to print CPU information at a later stage
Print CPU information within board_late_init().

This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:32 +02:00