This allows us to act like a serial device: we get tab chars and CTRL+C
and respond appropriately.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
Sandbox wants to support commands which use memory. The map_physmen()
call provides this feature, so should be used more consistently in
U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Matthias Weisser <weisserm@arcor.de>
The check for sandbox architecture is too early in the Makefile, so
standalone and api are built regardless. This moves the check until
after autoconf.mk has been read.
This fixes a build breakage.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file is required by the new DMA buffer alignment macro.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again. On some architectures
(especially ARM) this results in a large number of calls to gcc.
This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.
Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
-> grep execve /tmp/foo | wc -l
Before: After: Reduction:
==================================
P2020DS 20555 15205 -26%
qong 31692 14490 -54%
As a result, built times are significantly reduced, typically by
30...50%.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Albert Aribaud <albert.aribaud@free.fr>
cc: Graeme Russ <graeme.russ@gmail.com>
cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Fix:
post.c: In function 'post_log':
post.c:425:7: warning: variable 'i' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
cmd_ide.c: In function 'ide_ident':
cmd_ide.c:988:6: warning: variable 'do_retry' set but not used
[-Wunused-but-set-variable]
Delete the unused variable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Make file acceptable to checkpatch.
This is only a basic clean up to the extend possible without any real
changes to the source code. Warnings due to line over 80 characters
were accepted because these affect only printf()s with user visible
strings. No attempts were made to fix warnings about volatile and
externs - these need a more thorough cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ds1337.c: In function 'rtc_get':
ds1337.c:88:52: warning: variable 'control' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
4xx_pci.c: In function 'pci_init_board':
4xx_pci.c:855:6: warning: variable 'busno' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Fix:
mv_eth.c: In function 'mv64460_eth_real_open':
mv_eth.c:471:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_stop':
mv_eth.c:722:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_xmit':
mv_eth.c:796:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_receive':
mv_eth.c:877:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_get_stats':
mv_eth.c:979:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_update_stat':
mv_eth.c:1006:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c:1005:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_print_stat':
mv_eth.c:1087:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'eth_clear_mib_counters':
mv_eth.c:2141:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
4xx_enet.c: In function 'enet_rcv':
4xx_enet.c:1772:21: warning: variable 'ef_ptr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Fix:
4xx_uart.c: In function 'get_serial_clock':
4xx_uart.c:204:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Fix:
eepro100.c: In function 'read_hw_addr':
eepro100.c:926:6: warning: variable 'eeprom' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
strataflash.c: In function 'flash_write_cfiword':
strataflash.c:669:11: warning: variable 'ctladdr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'flash_erase':
flash.c:304:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
In addition, remove some dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ns8382x.c: In function 'ns8382x_check_duplex':
ns8382x.c:704:6: warning: variable 'hun' set but not used
[-Wunused-but-set-variable]
To fix this, we get rid of the NS8382X_DEBUG code and use standard
debug() instead.
This will now trigger a so far undetected warning:
ns8382x.c:780:2: warning: format '%X' expects argument of type
'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Fix that, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 1272592 "powerpc: Use getenv_ulong() in place of getenv(),
strtoul" instroduced a build warning for some PPC systems:
board.c: In function 'board_init_r':
board.c:626: warning: unused variable 's'
Fix it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
* 'master' of git://git.denx.de/u-boot-mmc:
tegra2: Move MMC clock initialization into MMC driver
mmc: sdhci: fix sdma bug for large file transfer
mmc: sdhci: add timeout for data transfer
mmc: sdhci: add mmc structure for host
mmc: sdhci: fix build warning
mmc: sdhci: fix cache flush
mmc: CMD7:MMC_CMD_SELECT_CARD response fix
mmc: test mmc bus width on startup
mmc: change magic number to macro define
mmc: mv_sdhci: fix 8bus width access for 88SV331xV5
mmc: retry the cmd8 to meet 74 clocks requirement in the spec
PXA: Add MMC driver using the generic MMC framework
* 'master' of git://git.denx.de/u-boot-x86:
x86: Fix a compiler warning in arch/x86/lib/realmode.c
x86: Remove the prototype for the unused function board_init
x86: Rename include/asm/ic to include/asm/arch-sc520
x86: turn off cache: set control register properly
* 'master' of git://git.denx.de/u-boot-nds32:
nds32: asm/io.h: add __iormb __iowmb and inline io support
nds32: cache: define ARCH_DMA_MINALIGN for DMA buffer alignment
nds32: Use getenv_ulong() in place of getenv(), strtoul
Commit 114d7fc0 "e1000: Rewrite EEPROM checksum error to give more
information" failed to initialize the checksum variable which should
result in random results. Fix that.
Commit 2326a94d caused a ton of "unused variable 'x'" warnings.
Fix these. While we are at it, remove some bogus parens.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
SDHCI spec need to reset the sdma base address while the software
try to accorss the 512k bytes address boundary. When meet such
accross behavior, sdhci controller would generate a interrupt
automatically, and software need handle this.
Signed-off-by: Lei Wen <leiwen@marvell.com>
If CONFIG_MMC_SDHCI_IO_ACCESSORS is defined, the following warning would
shows up:
include/sdhci.h:224: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:224: warning: its scope is only this definition or
declaration, which is probably not what you want
include/sdhci.h:225: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:226: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:227: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:228: warning: 'struct sdhci_host' declared inside
parameter list
include/sdhci.h:229: warning: 'struct sdhci_host' declared inside
parameter list
Signed-off-by: Lei Wen <leiwen@marvell.com>
As per JEDEC document JESD84-A441 (page 105) response for CMD7
(MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we
never take MMC to disconnected state and on powerup its always ideal
state which later goes to stand-by state.
from document footnote:
R1 while selecting from Stand-By State to Transfer State; R1b while
selecting from Disconnected State to Programming State.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
For we don't know mmc bus width from reading registers, the only way
to check is to test.
Current compare offset is:
EXT_CSD_PARTITIONING_SUPPORT
EXT_CSD_ERASE_GROUP_DEF
EXT_CSD_REV
EXT_CSD_HC_ERASE_GRP_SIZE
EXT_CSD_SEC_CNT
Signed-off-by: Lei Wen <leiwen@marvell.com>
Previous magic number is hard to parse its meaning, change it to
respective macro definition
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: WOlfgang Denk <wd@denx.de>
Marvell 88SV331xV5 platform's sdhci host control is not very standard
with the spec in the 8bit handling. It need to set its private register
to switch to the 8bit mode which is not included in the standard sdhci
registers.
This patch mainly hacks the writeb method, and set its private register
if it find the driver is going to switch to the 8bit mode.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For some controller it has dynamic clock gating, and only toggle out clk
when the first cmd0 send out, while some card strictly obey the 74
clocks rule, the interval may not be sufficient between the cmd0 and
this cmd8, retry to fulfil the clock requirement.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
1. This patch add required __iormb and __iowmb to io.h.
This also fix some misbehavior to periphal drivers.
This io.h has been fixed with referencing arm/include/asm/io.h.
2. This patch replaced macro writeb and readb into inline function.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
A followup patch will be adding a configurable feature to enable
programming of E1000 EEPROMs from the command line or via the generic
U-Boot SPI interface.
In order for it to work it needs access to certain E1000-internal
functions, so export those in the e1000.h header file.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
As an aide to debugging, we should print out the expected value of the
EEPROM checksum in addition to just saying that it is wrong.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
By allocating the e1000 device structures much earlier, we can easily
generate better error messages and siginficantly clean things up.
The only user-visable change (aside from reworded error messages) is
that a detected e1000 device which fails to initialize due to software
or hardware error will still be allocated a device number.
As one example, consider a system with 2 e1000 PCI devices where the
first controller has a corrupted EEPROM. Using the old code the
second controller would be "e1000#0", while with this change it would be
"e1000#1".
This change should hopefully make such EEPROM errors much more
straightforward to handle correctly in boot scripts and the like.
It is also necessary for a followup patch which allows SPI programming
of an e1000 controller's EEPROM even if the checksum is invalid.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Consolidate the test for a dual-port NIC to one location for easy
modification, then fix support for the dual-port 82571.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
