Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Use phydev->is_c45 instead of is_10g_interface(phydev->interface) to
determine whether clause 45 protocol should be used.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move PHY_INTERFACE_MODE_NA to the beginning of the enum definition to
make it have zero value. This makes it possible (although not
encouraged) to test for invalid/nonexistent interface mode with !val
instead of val == PHY_INTERFACE_MODE_NA.
The comment near the definition says "Must be last", because when the
constant was introduced in commit 5f184715ec ("Create PHY Lib for
U-Boot"), it was used as the maximum value when interating over the
constants. But this is no longer true - we use PHY_INTERFACE_MODE_MAX
for that now, and so we can move it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX to
make it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add wrappers dm_mdio_read(), dm_mdio_write() and dm_mdio_reset() for
DM MDIO's .read(), .write() and .reset() operations.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_get_phy_node() and dev_get_phy_node() and use it in
net/mdio-uclass.c function dm_eth_connect_phy_handle(). Also add
corresponding UT test.
This is useful because other part's of U-Boot may want to get PHY ofnode
without connecting a PHY.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.
As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.
[1] 3c35bfee83/dtschema/schemas/gpio/gpio.yaml (L17)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Based on current usage, migrate a number of DP-DDR related options to
Kconfig.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform has CONFIG_ETH_DESIGNWARE set already, which is the
correct value for the driver in question. Remove this incorrect line.
Signed-off-by: Tom Rini <trini@konsulko.com>
As no platforms override this value, set it for all mpc83xx platforms.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these two options to the arch Kconfig file.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This symbol is only possibly useful on some mvebu platforms, so move the
symbol there and select it for the only current user.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
A number of CONFIG options are used on these platforms as part of the
default environment. Set some of these more directly and in other
cases, just reference them directly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only enabled for CI_UDC and !TEGRA20, so implement it as
such in Kconfig directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
For platform which can boot on different device, this allows
to override interface, device and partition from board code
Signed-off-by: He Yong <hyyoxhk@163.com>
This file uses struct driver, so declare it at the top in case the
header-inclusion order is not as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is normally defined in stdint.h but is not used in U-Boot. When
libraries (such as Chromium OS vboot) are built against U-Boot they may
expect this value to be available. Add it to avoid build errors in this
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the header file defines this function in SPL but the file may
not actually be built. This causes a build error if the option is enabled.
Fix the condition in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use Sphinx style comments to describe functions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below
ZynqMP> mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000
Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.
So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.
Fixes: a744a284e3 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:
* Introduce a memory region "ss" to allow dt to provide DDRSS region,
which is not the same as "ctl" which is the controller region.
* Introduce a "ti,ecc-enable" flag which allows a memorycontroller
instance to enable ecc.
* Introduce functionality to properly program the DDRSS registers to
enable ECC for the full DDR memory space if enabled with above flag.
* Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
account from DDR memory that must be reserved for ECC operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
Most Allwinner sunxi SoCs have separate boot ROMs in non-secure and
secure mode. The "non-secure" or "normal" boot ROM (NBROM) uses the
existing sunxi_egon image type. The secure boot ROM (SBROM) uses a
completely different image type, known as TOC0.
A TOC0 image is composed of a header and two or more items. One item
is the firmware binary. The others form a chain linking the firmware
signature to the root-of-trust public key (ROTPK), which has its hash
burned in the SoC's eFuses. Signatures are made using RSA-2048 + SHA256.
The pseudo-ASN.1 structure is manually assembled; this is done to work
around bugs/quirks in the boot ROM, which vary between SoCs. This TOC0
implementation has been verified to work with the A50, A64, H5, H6,
and H616 SBROMs, and it may work with other SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
When u-boot is used as a chain-loaded bootloader (replacing OS kernel),
previous bootloader leaves data in RAM, that can be reused.
For example, on recent arm linux system, when chainloading u-boot,
there are initramfs and fdt in RAM prepared for OS booting. Initramfs
may be modified to store u-boot's payload, thus providing the ability to
use chainloaded u-boot to boot OS without any storage support.
Two config options added:
- SAVE_PREV_BL_INITRAMFS_START_ADDR
saves initramfs start address to 'prevbl_initrd_start_addr' environment
variable
- SAVE_PREV_BL_FDT_ADDR
saves fdt address to 'prevbl_fdt_addr' environment variable
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
We already support the NVMe commands and PCIe backend in the QEMU target,
so let's make it easy for anyone to consume them and enable NVMe distro
boot along the way!
With this patch, I can put an NVMe backed disk image into my QEMU VM and
have it automatically load a UEFI target blob.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Some serial drivers can be vastly more efficient when printing multiple
characters at once. Non-DM serial has had a puts option for these sorts
of drivers; implement it for DM serial as well.
Because we have to add carriage returns, we can't just pass the whole
string directly to the serial driver. Instead, we print up to the
newline, then print a carriage return, and then continue on. This is
less efficient, but it is better than printing each character
individually. It also avoids having to allocate memory just to add a few
characters.
Drivers may perform short writes (such as filling a FIFO) and return the
number of characters written in len. We loop over them in the same way
that _serial_putc loops over putc.
This results in around sizeof(void *) growth for all boards with
DM_SERIAL. The full implementation takes around 140 bytes.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a debugger is not attached to U-Boot, semihosting calls will raise a
synchronous abort exception. Try to catch this and disable semihosting
so we can e.g. use another uart if one is available. In the immediate
case, we return an error, since it is not always possible to check for
semihosting beforehand (debug uart, user-initiated load command, etc.)
We handle all possible semihosting instructions, which is probably
overkill. However, we do need to keep track of what instruction set
we're using so that we don't suppress an actual error.
A future enhancement could try to determine semihosting capability by
inspecting the processor state. There's an example of this at [1] for
RISC-V. The equivalent for ARM would inspect the monitor modei
enable/select bits of the DSCR. However, as the article notes, an
exception handler is still helpful in order to catch disconnected
debuggers.
[1] https://tomverbeure.github.io/2021/12/30/Semihosting-on-RISCV.html#avoiding-hangs-when-a-debugger-is-not-connected
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
These functions are intended to support detecting semihosting and
falling back gracefully to alternative implementations. The test starts
by making semihosting call. SYS_ERRNO is chosen because it should not
mutate any state. If this semihosting call results in an exception
(rather than being caught by the debugger), then the exception handler
should call disable_semihosting() and resume execution after the call.
Ideally, this would just be part of semihosting by default, and not a
separate config. However, to reduce space ARM SPL doesn't include
exception vectors by default. This means we can't detect if a
semihosting call failed unless we enable them. To avoid forcing them to
be enabled, we use a separate config option. It might also be possible
to try and detect whether a debugger has enabled (by reading HDE from
DSCR), but I wasn't able to figure out a way to do this from all ELs.
This patch just introduces the generic code to handle detection. The
next patch will implement it for arm64 (but not arm32).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This adds a serial driver which uses semihosting calls to read and write
to the host's console. For convenience, if CONFIG_DM_SERIAL is enabled,
we will instantiate a serial driver. This allows users to enable this
driver (which has no physical device) without modifying their device
trees or board files. We also implement a non-DM driver for SPL, or for
much faster output in U-Boot proper.
There are three ways to print to the console:
Method Baud
================== =====
smh_putc in a loop 170
smh_puts 1600
smh_write with :tt 20000
================== =====
These speeds were measured using a 175 character message with a J-Link
adapter. For reference, U-Boot typically prints around 2700 characters
during boot on this board. There are two major factors affecting the
speed of these functions. First, each breakpoint incurs a delay. Second,
each debugger memory transaction incurs a delay. smh_putc has a
breakpoint and memory transaction for every character. smh_puts has one
breakpoint, but still has to use a transaction for every character. This
is because we don't know the length up front, so OpenOCD has to check if
each character is nul. smh_write has only one breakpoint and one memory
transfer.
DM serial drivers can only implement a putc interface, so we are stuck
with the slowest API. Non-DM drivers can implement puts, which is vastly
more efficient. When the driver starts up, we try to open :tt. Since
this is an extension, this may fail. If it does, we fall back to
smh_puts. We don't check :semihosting-features, since there are
nonconforming implementations (OpenOCD) which don't implement it (but
*do* implement :tt).
Some semihosting implementations (QEMU) don't handle READC properly. To
work around this, we try to use open/read (much like for stdin) if
possible.
There is no non-blocking I/O available, so we don't implement pending.
This will cause __serial_tstc to always return true. If
CONFIG_SERIAL_RX_BUFFER is enabled, _serial_tstc will try and read
characters forever. To avoid this, we depend on this config being
disabled.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds three wrappers around the semihosting commands for reading and
writing to the host console. We use the more standard getc/putc/puts
names instead of readc/writec/write0 for familiarity.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This command's functionality is now completely implemented by the
standard fs load command. Convert the vexpress64 boot command (which is
the only user) and remove the implementation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds a filesystem which is backed by the host's filesystem. It is
modeled off of sandboxfs, which has very similar aims. Semihosting
doesn't support listing directories (except with SYS_SYSTEM), so neither
do we. it's possible to optimize a bit for the common case of reading a
whole file by omitting a call to smh_seek, but this is left as a future
optimization.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
In order to add filesystem support, we will need to be able to seek and
write files. Add the appropriate helper functions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
There's no point in using string constants for smh_open if we are just
going to have to parse them. Instead, use numeric modes. The user needs
to be a bit careful with these, since they are much closer semantically
to string modes used by fopen(3) than the numeric modes used with
open(2).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This exports semihosting functions for use in other files. The header is
in include/ and not arm/include/asm because I anticipate that RISC-V may
want to add their own implementation at some point.
smh_len_fd has been renamed to smh_flen to more closely match the
semihosting spec.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the FVP model just supports booting through semihosting, so by
loading files from the host the model is running on. This allows for
quick booting of new kernels (or replacing DTBs), but prevents more
featureful boots like using UEFI.
Enable the distro_boot feature, and provide a list of possible boot
sources that U-Boot should check:
- For backwards compatibility we start with semihosting, which gets its
commands migrated from CONFIG_BOOTCOMMAND into the distro_boot
infrastructure. This is also slightly tweaked to fail graceful in case
the required files could not be found.
- Next we try to use a user provided script, that could be easily
placed into memory using the model command line.
- Since we gained virtio support with the enablement of OF_CONTROL,
let's check virtio block devices next. This is where UEFI boot can
be easily used, for instance by providing a distro installer .iso
file through virtio-blk.
- Networking is now provided by virtio as well, so enable the default
PXE and DHCP boot flows, mostly because we can.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The definition of the standard environment variables (kernel_addr_r and
friends) has been improved lately for the FVP model, but the Juno board
is still using some custom scheme.
Since we need to extend this to a third board soon, let's unify the
definition:
- Define the Juno addresses in the same generic way we do for the FVP
model, and move the actual variable setting out of the board #ifdef's.
- Add the missing addresses for a PXE file and a boot script.
- Cleanup some stale comments on the way.
As the FVP model doesn't have support for distro_boot quite yet, add
a dummy definition for now, to be replaced with the real thing later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_USE_NANDFLASH and CONFIG_SYS_USE_MMC serve the
same purpose as CONFIG_SD_BOOT / CONFIG_NAND_BOOT so migrate to using
these switches instead as they're already in Kconfig.
Cc: Stelian Pop <stelian@popies.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of M5373EVB we always had NANDFLASH_SIZE=16, so just use it
directly. In the case of M5329EVB we had not removed the rest of NAND
support when saying we didn't have NAND, so instead use that to key off
of rather than NANDFLASH_SIZE.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The value CONFIG_DB_784MP_GP is only used in the DDR code to refer to
CONFIG_TARGET_DB_MV784MP_GP so just use that second value directly.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We only set one of these values ever at this point, so remove dead code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are a handful of variants around CONFIG_SYS_USE_DATAFLASH and none
of them now control anything further within their board config.h files,
so remove these from CONFIG_SYS_EXTRA_OPTIONS and then remove the empty
blocks in the board config.h files. In a few places further clean up
related logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM
This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit enhances mkimage to update the node
/image/pre-load/sig with the public key.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a stage pre-load to the command bootm.
Right now, this stage may be used to read a
header and check the signature of the full
image.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a stage pre-load that could
check or modify an image.
For the moment, only a header with a signature is
supported. This header has the following format:
- magic : 4 bytes
- version : 4 bytes
- header size : 4 bytes
- image size : 4 bytes
- offset image signature : 4 bytes
- flags : 4 bytes
- reserved0 : 4 bytes
- reserved1 : 4 bytes
- sha256 of the image signature : 32 bytes
- signature of the first 64 bytes : n bytes
- image signature : n bytes
- padding : up to header size
The stage uses a node /image/pre-load/sig to
get some informations:
- algo-name (mandatory) : name of the algo used to sign
- padding-name : name of padding used to sign
- signature-size : size of the signature (in the header)
- mandatory : set to yes if this sig is mandatory
- public-key (madatory) : value of the public key
Before running the image, the stage pre-load checks
the signature provided in the header.
This is an initial support, later we could add the
support of:
- ciphering
- uncompressing
- ...
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Most CCF drivers follow a common pattern where their clock ops defer the
actual operation to the backing CCF clock. Add some generic implementations
of these functions to reduce duplication of code.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220320203446.740178-1-seanga2@gmail.com
Most callers of this function do not check the return value, and it is
unclear what action they should take if it fails. If a function is freeing
multiple clocks, it should not stop just because the first one failed.
Since the callbacks can no longer fail, just convert the return type to
void.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-8-seanga2@gmail.com
When freeing a clock there is not much we can do if there is an error, and
most callers do not actually check the return value. Even e.g. checking to
make sure that clk->id is valid should have been done in request() in the
first place (unless someone is messing with the driver behind our back).
Just return void and don't bother returning an error.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220115222504.617013-2-seanga2@gmail.com
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_BCM2835
This is the final ad-hoc CONFIG_VIDEO_... to convert.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry)
Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND)
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add missing MEMA - MEMD register definitions for PFUZE100.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Macros PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* are unused and are
duplication of PCI_CLASS_* macros defined in pci_ids.h header file.
So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The block IO protocol may be installed on any handle. We should make
no assumption about the structure the handle points to.
efi_disk_is_system_part() makes an illegal widening cast from a handle
to a struct efi_disk_obj. Remove the function.
Fixes: Fixes: 41fd506842 ("efi_loader: disk: add efi_disk_is_system_part()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Let function efi_dp_find_obj() additionally check if a given protocol is
installed on the handle relating to the device-path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_dp_find_obj() should not return any handle with a partially matching
device path but the handle with the maximum matching device path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_GPIO_PULLUP
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
