Commit graph

725 commits

Author SHA1 Message Date
Keerthy
b12550eb9c board: ti: am571-idx: Add vcores support
Update vcores for am571-idk board.

Reported-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-06-05 14:13:11 -04:00
Lokesh Vutla
9cb5eaf2cf ARM: k2g: Fix passing main pll info for higher speeds
Main pll is marked as arm plls for higher speeds. Fix this.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-06-05 14:13:03 -04:00
Simon Glass
c62db35d52 arm: Add explicit include of <asm/mach-types.h>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:36 -04:00
Tom Rini
1d7f6ad2bf ti816x: Modernize the defconfig
- Switch to using <configs/ti_armv7_omap.h> and family.  This lets us
  drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
  that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:25 -04:00
Tom Rini
77e99277a2 ti816x: Enable NAND
The TI8168-EVM comes with NAND on board.  Enable it and move environment
over there.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:24 -04:00
Tom Rini
8627733941 ti816x: Rework DDR initialization sequence
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family.  In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations.  Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient.  Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still.  As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it.  We also remove a bunch
of other untested code about changing the speed the DDR runs at.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Sekhar Nori
4a72d8dcc9 board: ti: enable support for writing to fat partition
Enable support for writing to FAT partitions on
TI's boards.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2017-06-03 17:55:19 -04:00
Daniel Thompson
221a949eb6 Kconfig: Finish migration of hashing commands
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way.  As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
        migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-31 19:38:14 -04:00
Simon Glass
a1dc980d88 Convert CONFIG_CMD_EEPROM et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_EEPROM
   CONFIG_CMD_EEPROM_LAYOUT
   CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:49 -04:00
Tom Rini
4125bbcef6 Merge branch 'master' of git://git.denx.de/u-boot-mmc
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
  match other TI platforms in the same situation.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-16 08:10:50 -04:00
Tom Rini
cb33bda44f Merge branch 'master' of git://git.denx.de/u-boot-i2c 2017-05-15 13:01:26 -04:00
Tom Rini
8850c5d57c Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 10:40:05 -04:00
Masahiro Yamada
4aa2ba3a34 mmc: replace CONFIG_GENERIC_MMC with CONFIG_MMC
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature.  Deprecate the
former.

This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-15 18:28:23 +09:00
Simon Glass
64a144dcea i2c: omap: Modify code to work without CONFIG_I2C_HARD
Drop use of this long-deprecated option.

Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-15 06:18:20 +02:00
Lokesh Vutla
fbd6295da4 arm: am33xx: Add support for mulitiple PLL input frequencies
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:14 -04:00
Lokesh Vutla
0650798824 board: am335x: Introduce scale_vcores
Update voltages before programming plls.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-12 08:37:13 -04:00
Lokesh Vutla
4548bc8d0a am33xx: Provide platform data for mmc
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-11 22:21:28 -04:00
Cooper Jr., Franklin
e25ae3224f ti: common: board_detect: Set alen to expected value before i2c read
In non DM I2C read operations the address length passed in during a read
operation will be used automatically. However, in DM I2C the address length
is set to a default value of one which causes problems when trying to
perform a read with a differing alen. Therefore, before the first read in a
series of read operations set the alen to the correct value.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:04:39 +02:00
Cooper Jr., Franklin
c6b80b1392 ti: common: board_detect: Introduce function to set the address length.
Reading from the I2C EEPROM used typically requires using an address length
of 2. However, when using DM for I2C the default address length used is 1.
To fix this introduce a new function that allows the address length to be
changed. The logic to do so was copied from cmd/i2c.c.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:04:29 +02:00
Lokesh Vutla
ee3c6532be ARM: keystone2: Add support for getting external clock dynamically
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Lokesh Vutla
c5f177debc ARM: k2g: Add support for dynamic programming of PLL based on SYSCLK
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Lokesh Vutla
690485e01b board: ti: Define Kconfig symbol for common cmd options
Instead of defining command options in every defconfig,
define a common Kconfig symbol that consolidates all command
options that are supported by any TI platform. Also use imply
keyword so that that specific option can be disabled if
not required.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 11:57:36 -04:00
Uri Mashiach
1a9a5f7a39 usb: host: xhci-omap: fix double weak board_usb_init functions
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c

To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
  normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
  the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
  omap_xhci_board_usb_init.
  Done only for boards that defines CONFIG_USB_XHCI_OMAP.

To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
  board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
  to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
  omap_xhci_board_usb_cleanup.
  Done only for boards that defines CONFIG_USB_XHCI_OMAP.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
2017-05-08 11:38:37 -04:00
Simon Glass
ac60e46e7d Convert CONFIG_CMD_BAT to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BAT

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:30:00 -04:00
Lokesh Vutla
6cc96bc75a board: dra71: Fix selection of OPPs
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:

VDD_MPU:	OPP_NOM
VDD_CORE:	OPP_NOM
VDD_GPU:	OPP_NOM
VDD_DSPEVE:	OPP_NOM, OPP_HIGH
VDD_IVA:	OPP_NOM, OPP_HIGH

This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.

[1] http://www.ti.com/lit/ds/symlink/dra718.pdf

Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-27 16:49:04 -04:00
robertcnelson@gmail.com
52609d753b config: am335x_evm: detect BeagleBone Blue using BLA
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.

This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]

http://beagleboard.org/blue
https://github.com/beagleboard/beaglebone-blue

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:52 -04:00
robertcnelson@gmail.com
2b79fba691 config: am335x_evm: detect Green Wireless using GW1
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.

This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35  42 4e 4c 54 47 57 31 41  |.U3.A335BNLTGW1A|]

http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:52 -04:00
robertcnelson@gmail.com
4015949f1f config: am335x_evm: detect Black Wireless using BWA
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.

This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35  42 4e 4c 54 42 57 41 35  |.U3.A335BNLTBWA5|]

http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:51 -04:00
Sekhar Nori
411278b858 board: ti: am57xx: enable input on mmc clock
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.

Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.

Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).

Tested with HS and UHS SD card on AM572x EVM Rev A3.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 09:26:48 -04:00
Simon Glass
76b00aca4f board_f: Drop setup_dram_config() wrapper
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 16:36:51 -04:00
Roger Quadros
752a8311e9 ARM: k2g: setup PRU ethernet MAC addresses
PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:57:15 -04:00
Roger Quadros
66e04fb503 ARM: Use Kconfig for board EEPROM's I2C bus and chip address
In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:57:15 -04:00
Nishanth Menon
fcb185244b board: ti: am57xx-idk: Auto detect LCD Panel
AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.

Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.

NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).

Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf

Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:56:22 -04:00
Roger Quadros
629101294f board: ti: am571x-idk: Update pinmux for ICSS2 Ethernet
Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-03-20 17:56:22 -04:00
Roger Quadros
376110525e board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).

Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.

J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb

At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.

For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.

- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-03-20 17:56:22 -04:00
Roger Quadros
38f719ea5e ti: common: board_detect: commodify ethaddr environment setting code
Keystone and OMAP platforms will need this to set ethernet
MAC addresses from board EEPROM.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:56:22 -04:00
Lokesh Vutla
639892867a ti: common: board_detect: Rename EEPROM scratch start macro
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:56:22 -04:00
Jean-Jacques Hiblot
d5abcf94c7 ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-19 22:17:14 -04:00
Tom Rini
9d4f7a311f TI: Migrate board/ti/common/Kconfig to imply
The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:15 -05:00
Tom Rini
48dce3bfd9 am335x_evm: Switch to using imply keyword
These particular SPL options are part of what the ROM provides, but for
compatibility with how we have previously used them, move them to being
implied by the board being selected.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:15 -05:00
Semen Protsenko
7a2af751a0 arm: am57xx: Set serial# variable
serial# variable is used to correctly display device ID in
"fastboot devices". It also can be used further for displaying device ID
in "adb devices" (should be passed as "androidboot.serialno" to kernel
cmdline, via "bootargs" variable).

Serial number generating algorithm is described at [1].

[1] http://lists.denx.de/pipermail/u-boot/2015-March/207462.html

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-02-17 17:24:34 -05:00
Tom Rini
94ba26f2bc Revert "arm: Remove unregister MACH_TYPE_xxx uses"
This reverts commit 70b26cd057.

This is not a strict revert as it is easier to fix
board/atmark-techno/armadillo-800eva/armadillo-800eva.c to now the
correct name (same value) than to revert that change too.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28 14:04:22 -05:00
Uri Mashiach
2d8d190c83 status_led: Kconfig migration
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.

TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.

Tested boards: CL-SOM-AM57x, CM-T335

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-01-21 15:12:33 -05:00
Heiko Schocher
17fa032671 serial, ns16550: bugfix: ns16550 fifo not enabled
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.

Since the above patch, you have to setup the fcr register.

For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...

This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.

Detected this issue with automated tbot tests on am335x
based shc board.

The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)

Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-20 09:15:19 -05:00
Tom Rini
70b26cd057 arm: Remove unregister MACH_TYPE_xxx uses
Before we can sync with the latest mach-types.h file from the Linux
Kernel we need to remove some instances of MACH_TYPE_xxx from our
sources.  As these values have been removed from the canonical upstream
source we should not be using them either, so drop.

Cc: Tom Warren <twarren@nvidia.com>
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Nick Thompson <nick.thompson@gefanuc.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-14 12:18:11 -05:00
Jyri Sarha
8c17cbdf8a arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 15:00:03 -05:00
Keerthy
385d3632ba am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD
The GPIO7 pad mux should be programmed to POWERHOLD value
as per board design. In cases where the PMIC is shut off the
mux is set to GPIO7 mode. So during initialization to be on the
safer side set the mode to POWERHOLD.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:09 -05:00
Jean-Jacques Hiblot
a3a23c97b6 ARM: DRA7: AMxx: Make sure that the SPL always reads the configuration EEPROM
The bootrom may corrupt the area of SRAM used to store the ti_common_eeprom
structure. This patch makes sure that it's always read after a reset, even
if a valid MAGIC number is found in the SRAM.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-05 11:04:40 -05:00
Schuyler Patton
45e7f7e78b ARM: dts: AM571x-IDK Initial Support
Add initial DTS support for AM571-IDK evm.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:56 -05:00
Steve Kipisz
4d8397c66f board: ti: am57xx: Add support for the am571x idk
The AM571x Industrial Development Kit (IDK) is a board based on TI's
AM571x SoC which has a single core 1.5GHz Cortex-A15processor. This
board is a development platform for the Industrial Market with:

- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The PRU/ICSS will be supported by 3rd party software for EtherCat,
Profibus, and other Industrial protocols.

The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:55 -05:00
Lokesh Vutla
c887bef89b board: ti: am572x-idk: Update pinmux using latest PMT
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
20th October, 2016 by "Steve Kipisz <s-kipisz2@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".

[1] https://dev.ti.com/pinmux/app.html#/default/

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:55 -05:00
Nishanth Menon
89a38953bd board: ti: am572x: Add pinmux for X15/GPEVM SR2.0 using latest PMT
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".

[1] https://dev.ti.com/pinmux/app.html#/default/

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:55 -05:00
Nishanth Menon
5d43e168eb board: ti: am57xx: Update SR1.1 RGMII0 iodelay timings for x15/GPEVM
Update the timing for RGMII0 interface based on
PCT_DRA75x_DRA74x_SR1.1_v1.3.10 version (Jan 2016). This update
is for SR1.1

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:54 -05:00
Lokesh Vutla
f7f9f6be95 board: ti: am57xx: Add support for detection of X15 revb1
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:54 -05:00
Nishanth Menon
bf43ce6ca6 board: ti: am57xx: Add support for detection of reva3 variations for GPEVM
AM57xx evm Rev A3 with SR2.0 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev A3 variations.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:54 -05:00
Lokesh Vutla
40de70fbf7 ARM: dts: dra71x-evm: Add DT support
Add DT support for dra71-evm and built it as part of FIT image.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:51 -05:00
Keerthy
f56e635099 board: ti: dra71x-evm: Add PMIC support
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.

Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.

[1] http://www.ti.com/product/DRA718/technicaldocuments

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:50 -05:00
Nishanth Menon
4596cf98cd board: ti: dra72: Introduce optimization for rgmii timing for rev C
Rev C version of EVM does require IODelay to be configured for RGMII
pins in MANUAL_1 configuration. Update the same based on PG2.0 initial
simulation values.
Data based on PCT_DRA72x_SR2.0_SR1.0_v1.3.0.7

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:50 -05:00
Lokesh Vutla
4d74804818 board: ti: dra71x-evm: Add mux settings
Add mux and iodelay settings for dra71x-evm.
Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016).

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:49 -05:00
Lokesh Vutla
463dd22531 board: ti: dra71x-evm: Add epprom support
The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized
entry infotainment systems such as display audio and is a software compatible
derivative of the highly successful DRA74 and DRA72 processor families.
More information can be found here[1].

Add epprom detection for dra71-evm.

[1] http://www.ti.com/product/dra718

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:49 -05:00
Lokesh Vutla
beb71279d8 ARM: OMAP4+: Add support for dynamically selecting OPPs
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:48 -05:00
Andrew F. Davis
1b597ada36 board: ti: am57xx: add FIT image TEE processing
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:23 -05:00
Andrew F. Davis
0fcc5207ba board: ti: dra7xx: add FIT image TEE processing
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:22 -05:00
Lokesh Vutla
5d4d436c6d ARM: AMx3xx: Make FIT boot as default boot on HS devices
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:09 -05:00
Lokesh Vutla
82cca5a6be ARM: AM57xx: Make FIT boot as default boot on HS devices
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:09 -05:00
Lokesh Vutla
71c1b58e89 ARM: DRA7: Make FIT boot as default boot on HS devices
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:08 -05:00
Andrew F. Davis
ac34286647 keystone2: Move target selection to Kconfig
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-11-28 15:10:34 -05:00
Tom Rini
ca39bd8ce1 am57xx: Remove unused variable warnings
Starting with the changes to fix USB host on am57xx/am43xx we stopped
using usb_otg_ss1/related stuff and but we hadn't been enabling the
relevant options to cause the warnings until just recently.

Fixes: 55efadde7e (ARM: AM57xx: AM43xx: Fix USB host)
Fixes: a48d687c57 (configs: am57xx: Enable download gadget)
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:58 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Lokesh Vutla
4d0fec0e69 ARM: k2g: Update PLL Multiplier and divider values
Only a certain set of PLLM/D values are recommended to configure the DDR
at the required speeds for a given clock input frequency. Updating these
values as specified in Data Sheet[1] Table 5-18

[1] http://www.ti.com/lit/ds/symlink/66ak2g02.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:37 -05:00
Alex G
c19a28bc65 board: am335x/mux: Do not hang when encountering a bad EEPROM
In most cases, the SPL and u-boot.img will be on the same boot media.
Since the SPL was loaded by the boot rom, the pinmux will already have
been configured for this media. This, the board will still be able to
boot successfully, or at least reach the u-boot console, where more
recovery options are available.

I've encountered this on a beaglebone black with a corrupted EEPROM.
Removing this check allowed the board to boot successfully. I've also
seen this on EVM-based boards with an unprogrammed EEPROM. On those
boards, for some reason there were no UART messages. This made it look
as if the SOC was dead.

Remove the hang(), as it is not a fatal error. Also reformat the error
message to be clearer as to the cause. The original message made it
appear as if the wrong binary was being loaded.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:35 -05:00
Nishanth Menon
7774e97aa7 ti: common: board_detect: Return a valid empty string for un-initialized eeprom
Current logic for query of revision, board_name, config returns
NULL. Users of these functions do a direct strncmp to compare.
Unfortunately, as per conventions require two valid strings to compare
against and the current implementation causes a crash when compared
with NULL.

We'd still like to maintain the simplistic usage of these APIs instead
of redundant if (string) res=strncmp(fn(),"cmp",n); flowing all over
the place.

Hence, since the version, name and config is already pre-initialized
with empty string, just dont check for invalid header in the first
place and return the empty string to the caller.

Reported-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Correct was'nt -> wasn't typo]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:12:21 -04:00
Nishanth Menon
2a78c9e719 ti: common: board_detect: Setup initial default value for config as well
config should have been initialized along with others as defaults.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:04:21 -04:00
Nishanth Menon
28d624be62 ti: common: board_detect: Replace hardcoded value with macro
We should have used TI_DEAD_EEPROM_MAGIC in the first place.

Fixes: d3b98a9eb9 ("ti: common: dra7: Add standard access for board description EEPROM")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:04:21 -04:00
Roger Quadros
f411b5cca4 board: am335x: Always set eth/eth1addr environment variable
Ethernet ports might be used in the kernel even if CPSW driver
is disabled at u-boot. So always set ethaddr and eth1addr
environment variable from efuse.

Retain usbnet_devaddr as it is required for SPL USB eth boot.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:10 -05:00
Roger Quadros
e607ec993b board: am335x-icev2: add ethernet phy mode detection logic
Both ethernet ports can be used as CPSW ethernet (RMII mode)
or PRU ethernet (MII mode) by setting the jumper near the port.
Read the jumper value and set the pinmux, external mux and
PHY clock accordingly.

As jumper line is overridden by PHY RX_DV pin immediately
after bootstrap (power-up/reset), we have to use GPIO edge
detection to capture the jumper line status.

As u-boot doesn't provide any infrastructure for GPIO edge
detection, we directly access the GPIO registers.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:06 -05:00
Mugunthan V N
1053a769fb board: ti: dra7xx: complex definitions should be protected with parentheses
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Mugunthan V N
e8131386dc ARM: dts: dra72: add rev C evm support
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Andrew F. Davis
b0a4eea1a0 board: am33xx-hs: Allow post-processing of FIT image on AM33xx
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:10:01 -04:00
Lokesh Vutla
e92a6b2ee3 board: ks2: Enable ECC using detected DDR size
EEC is being enabled based on the ddr size populated by SPD data.
But not all keystone platforms have SPD data to detect ddr3 size.
So, enable ECC using the detected DDR size.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:05 -04:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Masahiro Yamada
63a7578e4e arch, board: squash lines for immediate return
Remove unneeded variables and assignments.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
2016-09-23 17:53:53 -04:00
Simon Glass
696a91f2b0 Convert CONFIG_SPL_YMODEM_SUPPORT to Kconfig
Convert CONFIG_SPL_YMODEM_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:23 -04:00
Simon Glass
02e69a5db1 Convert CONFIG_SPL_WATCHDOG_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:23 -04:00
Simon Glass
e00f76cee9 Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:19 -04:00
Simon Glass
2253797d28 Convert CONFIG_SPL_POWER_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:18 -04:00
Simon Glass
d6b9bd8923 Convert CONFIG_SPL_NAND_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:14 -04:00
Simon Glass
1fdf7c64ed Convert CONFIG_SPL_MMC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:13 -04:00
Simon Glass
cc4288ef42 Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
1646eba85c Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
77d2f7f507 Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:11 -04:00
Simon Glass
9c21df1547 Convert CONFIG_SPL_I2C_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
53b5bf3c1d Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
ae56db5f1c Convert CONFIG_SPL_FAT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
75eba2c45e Convert CONFIG_SPL_EXT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:09 -04:00
Simon Glass
256fe86b60 Convert CONFIG_SPL_ENV_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:08 -04:00
Lokesh Vutla
01c5075506 board: ks2: README: Update to add K2G support
Update the README to add support for K2G EVM. Also
- Add steps on how to use MMC boot
- Fix load address when using CCS
- Update build target to u-boot.bin from u-boot-dtb.bin as all ks2
  platforms uses DT.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07 13:52:20 -04:00
Nishanth Menon
c989166037 board: am57xx: Fix missing check for beagle_x15
When beagleboard-X15 is booted, we see the following log:
Unidentified board claims BBRDX15_ in eeprom header

This is because of the missing check for x15 (the default) and reports
an error for a valid board configuration. Fix the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07 08:49:05 -04:00
Nishanth Menon
c0b1d80a10 board: am57xx: MAINTAINERS: Update for current maintainer
Felipe Balbi has move on from TI and the current email ID is no longer
valid. So, replacing with Lokesh.

While at it, update missing config file which was untracked.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-07 08:49:04 -04:00
Tom Rini
584550d76a omap3: Drop omap3_evm_quick_* targets
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features.  At this point in time they no longer serve a good purpose so
remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 20:53:53 -04:00
Madan Srinivas
e29878fc47 arm: am4x: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:23 -04:00
Andreas Dannenberg
17c2987336 arm: omap5: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:22 -04:00
Lokesh Vutla
df6b506f16 ti_omap5_common: Find right dtb file for DRA72-RevC Evm
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-07-01 17:42:57 -04:00
Andreas Dannenberg
4aae64c22a ARM: AM437x: Align HS device variant defconfig filename
Align the name of the defconfig file for high-security (HS) device variants
from the AM43xx family of SoCs with the corresponding name used for the
general purpose devices. This allows for easier cross-association of those
files and also provides room to grow from an HS device part number
perspective.

Furthermore, update and cleanup associated MAINTAINERS file.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Madan Srinivas <madans@ti.com>
2016-07-01 17:42:53 -04:00
Peng Fan
d14739ffe1 Kconfig: make NOR_BOOT a common option
Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-27 22:32:07 -04:00
Lokesh Vutla
1736121b24 board: am437x-hs: spl: Select right dtb from fit
Select a right dtb from FIT for am437x-hs platform.

Reported-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:38 -04:00
Schuyler Patton
332dddc6a1 ARM: dts: AM572x-IDK Initial Support
Add initial DTS support for AM572-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:38 -04:00
Lokesh Vutla
7a0ea589ba board: am57xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs away to
detect the right dtb to be used. Adding support for the same for am57xx
platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Lokesh Vutla
165bd7a1cc board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVM
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.

Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Keerthy
1428d83270 arm: dra7xx: Assign omap_vcores based on board type
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12 13:14:57 -04:00
Lokesh Vutla
ca5599c3fb ARM: DRA7xx: Enable FIT for hs platforms
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-06 13:39:17 -04:00
Lokesh Vutla
e2924e5904 ARM: k2g: Configure reset mux to device reset
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.

Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.

Right now to give a default watchdog behaviour "Device reset" is
being selected.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2016-06-02 21:42:19 -04:00
Keerthy
eafd4644c0 arm: am57xx: Fix alignment where necessary
This just fixes alignment for better readability.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Keerthy
d60198dac2 arm: am57xx: Fix omap_vcores assignment for am572x-idk
Currently omap_vcores is wrongly assigned a default value of
beagle_x15_volts. Hence populating a new structure for am572x-idk
and assigning it to omap_vcores in the vcores_init function.

Fixes: c020d355c4 ("board: ti: am57xx: Add support for am572x idk in SPL")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Anna, Suman
e42523f544 ARM: DRA7: Consolidate voltage macros across different SoCs
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.

This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:17 -04:00
Anna, Suman
27c9596f68 ARM: DRA7: Define common macros for efuse register offsets
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:16 -04:00
Roger Quadros
55efadde7e ARM: AM57xx: AM43xx: Fix USB host
CONFIG_USB_XHCI_OMAP can be set for host mode without setting
CONFIG_USB_DWC3 which is meant for gadget mode only.
board_usb_init() was not being defined for CONFIG_USB_XHCI_OMAP
resulting in a data abort on usb start.

Define board_usb_init() for CONFIG_USB_XHCI_OMAP case. Move
gadget specific handling to within CONFIG_USB_DWC3.

Fixes: 6f1af1e358 ("board: ti: invoke clock API to enable and disable clocks")
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:15 -04:00
Lokesh Vutla
3d16389c90 board: am335x: Allow to choose serial device dynamically
Different AM335x based platforms have different serial consoles. As serial
console is Kconfig option a separate defconfig has to be created for each
platform. So pass the serial device dynamically.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:54 -04:00
Lokesh Vutla
73ec696059 ARM: dts: AM335x-ICEv2: Add minimal dts support
Add minimal dts support for AM335x-ICEv2 board

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-05-27 15:47:53 -04:00
Lokesh Vutla
97f3a178b2 board: AM335x-ICEv2: Add cpsw support
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done:

1)There are few on board jumper settings which gives a choice between
cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting
this, there are few GPIOs which control these muxes that needs to be held high.

2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected
via I2C. This needs to properly programmed and locked for PHY operation.
And PHY needs to be reset before before being used, which is also held by
a GPIO.

3) RMII mode needs to be selected.

[1] http://www.ti.com/lit/zip/tidr336
[2] http://www.ti.com/lit/ds/symlink/cdce913.pdf

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Lokesh Vutla
d8ff4fdb10 board: AM335x-ICEv2: Add DDR data
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
866b178bd1 board: AM335x-ICEv2: Add pinmux support
Add necessary pinmux support for AM335x ICEv2 board.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
a964332472 board: AM335x-ICEv2: Add epprom support
Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specific initialization can be done.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:50 -04:00
Lokesh Vutla
da9d9599ac ARM: dts: AM335x-BBG: Add initial support
Add initial DTS support for AM335x-BBG

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
3819ea7063 ARM: dts: AM335x-evmsk: Add initial support
Add initial DTS support for AM335x-evm sk.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
80b24fcd30 ARM: AM335x: Enable FIT
Use a single defconfig for all AM335x platforms by enabling FIT

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:48 -04:00
Lokesh Vutla
505ea6e82a board: am33xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:47 -04:00
Lokesh Vutla
54a92e1ad8 ARM: dts: AM437x-IDK Initial Support
Add initial DTS support for AM437x-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Lokesh Vutla
7dd1283048 ARM: dts: AM43x-EPOS Initial Support
Add initial DTS support for AM43-EPOS evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Lokesh Vutla
4c4e3b3775 ARM: AM43xx: Enable FIT
Use a single defconfig for all AM43xx platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
5a3775a422 board: AM43xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
cfd921f7cc ARM: DRA7: configs: Remove obsolete configs
Removing:
uart3_defconfig:
Now uart3 can be selected using menuconfig, removing separate
config for uart mode. Doing uart boot is not straight forward as ROM uses
uart3 as default serial console. In order to boot to prompt, concole in both
u-boot and kernel needs to be changed.

qspiboot_defconfig:
The only advantage of enabling QSPI_BOOT is selecting env in QSPI.
Eventually env needs to be selected by menuconfig so removing
qspiboot_defconfig. qspiboot can be done using dra7xx_evm_defconfig.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
bd7245849f ARM: DRA7: Enable FIT
Use a single defconfig for all DRA7 platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:44 -04:00
Lokesh Vutla
09da87dafd board: dra7: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:43 -04:00
Daniel Allred
62a09f0535 ARM: omap5: add ft_board_setup for dra7xx/am57xx
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.

Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:38 -04:00
Madan Srinivas
a5051b727e ti: AM43xx: board: Detect AM43xx HS EVM
Adds code to detect AM43xx HS EVMS - the string in the
I2C EEPROM for HS EVMs differs from GP EVMs. Adds code to
for evm detection, regardless of whether the evm is for
GP or HS parts, and updates board init to use that.

Modifies findfdt command to pick up am437x-gp-evm.dtb for
the HS EVMs also, as the boards are similar except for
some security specific changes around power supply and
enclosure protection.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:35 -04:00
Robert P. J. Day
7ffe3cd62e Delete tests of CONFIG_OF_LIBFDT when testing CONFIG_OF_BOARD_SETUP
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:

  config OF_BOARD_SETUP
          bool "Set up board-specific details in device tree before boot"
          depends on OF_LIBFDT
          ...

remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:16 -04:00
Nishanth Menon
e52e334e5c ARM: DRA7: Add ABB setup for all domains
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:41 -04:00
Nishanth Menon
3708e78c33 ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.

Hence, move the txdone mask definition over to structure describing
voltage domain.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:39 -04:00
Lokesh Vutla
8f69523213 memory: Move TI_AEMIF config to KCONFIG
Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:43 -04:00
Steve Kipisz
c020d355c4 board: ti: am57xx: Add support for am572x idk in SPL
The AM572x-IDK board (Industrial Dev Kit) is a board based on TI's AM5728x
SOC which has a dual core 1.5GHz A15 processor. This board is a development
platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728

NOTE: DT support is still pending upstream kernel acceptance but we
should be able to get the base system support with this patch.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:32 -04:00
Schuyler Patton
5f405e7fa0 board: ti: am57xx: Update EMIF SDRAM 1 and 3 Timings
Update EMIF data based on recommendations from the now standard TI
EMIF tool version 1.1.1 based on 256MBx16 DDR3L Kingston D2516EC4BXGGB
data sheet

Update T_RRD from 5 to 6 based on AM57xx TRM -
Minimum number of DDR cycles from activate to ativate for a different
bank, minus 1.

Update T_CKESR from 4 to 3 based on AM57xx TRM - Minimum number of DDR
clocks cycles for which SDRAM must remain in self refresh, minus 1.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:32 -04:00
Daniel Allred
7e52e11f35 am57x: Move CONS_INDEX to Kconfig
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
      into Kconfig proper.
    - Edit the relevant am57x configs to remove the now unneeded
      CONFIG_SYS_EXTRA_OPTIONS.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:31 -04:00
Roger Quadros
c3333ded03 board: ti: am57xx: Prevent init_sata() from being called twice
init_sata() is done as part of scsi_init() in
arch/arm/cpu/armv7/omap-common/sata.c so no need to duplicate
it here.

This seems to fix SATA problems in the kernel when CONFIG_TI_PIPE3 is
configured as loadable module.

Cc: Cooper Jr., Franklin <fcooper@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-04-11 20:48:21 -04:00
Dan Murphy
39fbac91e1 board: ti: DRA7: Add DP83867 TI phy for rev c
Enable the TI DP83867 Giga bit phy on the
dra7 rev c board.  The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:18:07 -04:00
Roger Quadros
92667e89fc board: ti: am57xx: Set ethernet MAC addresses from EEPROM to env
The MAC addresses for the PRU Ethernet ports will be available in the
board EEPROM as an address range. Populate those MAC addresses (if valid)
into the u-boot environment so that they can be passed on to the
device tree during fdt_fixup_ethernet().

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:27 -04:00
Nishanth Menon
8cac14719d board: ti: DRA7: Add DRA72-rev C evm pinmux
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.

Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:16 -04:00
Ravi Babu
6b1c14bb67 board: ti: DRA72: revC evm: Update sdram timing configuration for SR2.0
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.

Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.

Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:14 -04:00
Vitaly Andrianov
b8dafa2209 ti: k2g: increase phy autoneg timeout
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation
timeout. This commit increases the timeout to fix the issue.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:07 -04:00
Alexander Graf
50149ea37a efi_loader: Add runtime services
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.

This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.

We could maybe in the future map U-boot environment variables to EFI variables
here.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15 18:03:10 -04:00