It will take more than 1s when wake up from deep sleep. Most of the
time is spent on outputing information. This patch reduced the deep
sleep latency by:
1. avoid outputing system informaton
2. remove flush cache after DDR restore
3. skip reloading second stage uboot binary when SD boot
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The ITS bit was being read incorrectly beacause of operator
precedence. The same ahs been corrected.
Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For the Chain of Trust, the esbc_validate command supports
32 bit fields for location of the image. In the header structure
definition, these were declared as pointers which made them
64 bit on a 64 bit core.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in
SD boot now. For the customer's demand, QSPI needs to be supported in SD
boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is
used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is
used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This commit fixes a typo in vf610twr DRAM init that was causing a hang in
U-Boot for the Vybrid Tower. This typo was introduced in commit 3f353cecc
(vf610: refactor DDRMC code).
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
We use outer pmic reset and drop internal reset signal, bmode will
not work as expected, so drop boot mode code for 7dsabresd board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Adrian Alonso <aalonso@freescale.com>
Add MAINTAINERS info for mx6slevk_spl, mx6ul_9x9_evk and mx6qpsabreauto.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
We have defined this kconfig entry in arch/arm/cpu/armv7/mx7/Kconfig,
no need to redefine it in board Kconfig.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
get_board_rev() is not actually providing the board revision.
It just returns the CPU revision instead.
As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_board_rev() is not actually providing the board revision.
It just returns the CPU revision instead.
As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Include <usb/ehci-fsl.h> in order to fix the following sparse warning:
board/freescale/mx7dsabresd/mx7dsabresd.c:538:5: warning: symbol 'board_ehci_hcd_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We use trigger pmic reset to reset the board, so set bit SRS to
disable internal WDOG_RESET_B_DEB to make reset stable.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.
Boot Log:
U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)
CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The emulator with DDR3 model was used during model bringup. DDR4
controllers are used with ls2085a. Drop the DDR4 target defconfig
and enable DDR4 in ls2085a_emu_defconfig.
Signed-off-by: York Sun <yorksun@freescale.com>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
It supports followings
- Card can operate with up to 4 QSGMII lane simultaneously
- Card can operate with up to 8 SGMII lane simultaneously
Add support of X-QSGMII-16PORT riser card.
This patch also take care of back-ward compatiblity with old SGMII rise cards
used on LS2085QDS Platform.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Per new requirement, change default core frequency
from previous 1400MHz to 1200MHz to save power.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If enable DM PMIC and REGULATOR, we should not use original power
framework. So need to comment out the pfuze code for original power
framework, when CONFIG_DM_PMIC_PFUZE100 defined.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
On LS1021A Rev2.0, OCRAM's security level needs to be changed to
non-secure access for SD boot. This patch will allow OCRAM
access permission as R/W in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Program the external regulator to switch off voltage in deep sleep.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
