Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DMA for MMCs can be enabled, since the previous patch fixes
the following issue in SPL:
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set DDR as non-secure so that MMC DMA can access.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from bfe741ab9e and 73d952acc8 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fixes the microSD slot on the ASUS C201.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com<mailto:peng.fan@nxp.com>>
When an image is signed/encrypted on K2 devices the image may get padded
to meet alignment requirements for the signature/encryption type. The
original size is appended as 4 bytes little-endian to the end of the
final image.
Normally the trailing extra bytes are ignored and so restoring the
exact original size is not important. In the case of initrd the
original size is important as the kernel uses it to look for
additional filesystem data and can do the wrong thing when the
size is not correct.
Read off the original size and report it back from the image post
processing stage.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we have enabled the driver-model in SPL, we can remove the
code disabling NAND self-init in SPL from the config include for
omapl138-lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Enable CONFIG_SPL_DM and enable the driver model for serial by defining
an appropriate device in the board file for da850-lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We're working towards enabling the driver-model in SPL for da850-lcdk.
Enable CONFIG_USE_TINY_PRINTF in defconfig to reduce SPL size.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We're working towards enabling the driver model in SPL for da850-lcdk.
Enable SPL_SYS_MALLOC_SIMPLE in defconfig to reduce SPL size.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Extend the davinci NAND driver to support the driver model. For now this
doesn't add any device-tree parsing due to the fact that we can't access
the actual nand node on the device-tree - it's a subnode of the aemif
device and we don't have an aemif driver on davinci at the moment.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The following warning is emited when building u-boot for da850-lcdk:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
While we could fix it by selecting CONFIG_DM_SPI, there's no need to
build it at all as SPI is disabled on da850-lcdk. Remove all unneeded
options from the defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
There are no more users of the compatibility layer for i2c. Remove the
driver and all references to it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
There are no more "real" users of CONFIG_DM_I2C_COMPAT and we'll soon
remove it altogether. Stop building it in sandbox mode.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This option is no longer used on any davinci board but still selected
in defconfigs which causes the following warning:
===================== WARNING ======================
This board uses CONFIG_DM_I2C_COMPAT. Please remove
(possibly in a subsequent patch in your series)
before sending patches to the mailing list.
====================================================
Remove all references to CONFIG_DM_I2C_COMPAT from davinci.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has been abandonded for a while. I do not have this hardware
and nobody has appeared to notice and/or care that it's orphaned.
Since much of this code is inserted into the da850evm code base, removing
it from support will make da850evm support easier going forward.
This patch removes the da850_am18xxevm_defconfig, README references to this
board and the reference to this board from the MAINTAINERS list.
Signed-off-by: Adam Ford <aford173@gmail.com>
binman only accepts the -D argument early on the command-line, yet the
Makefile currently passes it near the end. This causes the build to fail
if this feature is used. Re-order the command-line to fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a 'replace' command to binman to permit entries to be replaced, either
individually or all at once (using a filter).
Signed-off-by: Simon Glass <sjg@chromium.org>
This code has three distinct phases:
1. The image is loaded and the state module is set up
2. The entry is written to the image
3. The image is repacked and written back to the file
Split the code out with three separate functions, one for each phase.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present some tests leave behind output directories. This happens
because some tests call binman, which sets up an output directory, then
call it again, which sets up another output directory and leaves the
original one behind.
Fix this by using a separate temporary directory when binman is called
twice, or by manually removing the output directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the state module holds references to all the device trees used by
binman, it must be updated when the device trees are updated. Add support
for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present outdir remains set ever after the output directory has been
removed. Fix this to avoid trying to access it when it is not present.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present binman cannot replace data within a CBFS since it does not
allow rewriting of the files in that CBFS. Implement this by using the
new WriteData() method to handle the case.
Add a header to compressed data so that the amount of compressed data can
be determined without reference to the size of the containing entry. This
allows the entry to be larger that the contents, without causing errors in
decompression. This is necessary to cope with a compressed device tree
being updated in such a way that it shrinks after the entry size is
already set (an obscure case). It is not used with CBFS since it has its
own metadata for this. Increase the number of passes allowed to resolve
the position of entries, to handle this case.
Add a test for this new logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this method assumes that the parent section does not need
to recalculate its position or adjust any metadata it may contain. But
when the entry changes size this may not be true. Also if the parent
section is more than just a container (e.g. it is a CBFS) then the
section may need to regenerate its output.
Add a new WriteChildData() method to sections and call this from the
WriteData() method, to handle this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we simply extract the data directly from entries using the
image_pos information. This happens to work on current entry types, but
cannot work if the entry type encodes the data in some way. Update the
ReadData() method to provide the data by calling a new ReadChildData()
method in the parent. This allows the entry_Section class, or possibly
any other container class, to return the correct data in all cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Intel descriptor must always appear at the start of an (x86) image,
so it is supposed to position itself there always. However there is no
explicit test for this. Add one and fix a bug introduced by the recent
change to adjust Entry to read the node in a separate call.
Signed-off-by: Simon Glass <sjg@chromium.org>
The FMAP is not intended to show the files inside a CBFS. The FMAP can be
used to locate the CBFS itself, but then the CBFS must be read to find out
what is in it.
Update the FMAP to work this way and add some debugging while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function appears to copy only the data before the struct
region and the data in the string region. It does not seem to copy the
struct region itself.
>From the arguments of this function it seems that it should support fdt
and buf being different. This patch attempts to fix this problem.
Upstream commit: c72fa77 libfdt: Copy the struct region in fdt_resize()
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes an entry may shrink after it has already been packed. In that
case we must repack the items. Of course it is always possible to just
leave the entry at its original size and waste space at the end. This is
what binman does by default, since there is the possibility of the entry
changing size every time binman calculates its contents, thus causing a
loop.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes entries shrink after packing. As a start towards supporting
this, update the _testing entry to handle the test case.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far we don't allow entries to change size when repacking. But this is
not very useful since it is common for entries to change size after an
updated binary is built, etc.
Add support for this, respecting the original offset/size/alignment
constraints of the image layout. For this to work the original image
must have been created with the 'allow-repack' property.
This does not support entry types with sub-entries such as files and
CBFS, but it does support sections.
Signed-off-by: Simon Glass <sjg@chromium.org>
The positioning does not currently work correctly if at the end of an
image with no fixed size. Also if the header is in the middle of an image
it can cause a gap in the image since the header position is normally at
the image end, so entries after it are placed after the end of the image.
Fix these problems and add more tests to cover these cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that an Image is an Entry_section, there is no need for the separate
BuildSection() function. Drop it and add a bit of logging.
Signed-off-by: Simon Glass <sjg@chromium.org>
When reading an image in, write its fdtmap to a file in the output
directory. This is useful for debugging. Update the 'ls' command to set up
the output directory; otherwise it will fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
