This reverts commit f5315dd629.
[why]
TPL is not mandatory for not all Rockchip SoCs, some SoCs like
RK356x, and RK3588 still use mainline u-boot without TPL as
their ddr init programs are accessed via binaries provided by
Rockchip instead of ddr source code.
Marking TPL build makes it not able to build u-boot.itb on
RK356x targets so revert this so that it can build an SPL build
that would support all across Rockchip platforms.
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Tested-by: Anand Moon <linux.amoon@gmail.com> # CM3
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The SK architecture comprises of baseboard and a SOM board. The
AM68 Starter Kit's baseboard contains most of the actual connectors,
power supply etc. The System on Module (SoM) is plugged on to the base
board. Therefore, add support for peripherals brought out in the base
board.
Schematics: https://www.ti.com/lit/zip/SPRR463
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
AM68 Starter Kit (SK) is a low cost, small form factor board designed
for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high
performance vision accelerators, hardware accelerators, latest C71x
DSP, high bandwidth real-time IPs for capture and display. The SoC is
power optimized to provide best in class performance for industrial
applications.
AM68 SK supports the following interfaces:
* 16 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.1 Type-C port
* x2 USB 3.1 Type-A ports
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
SK's System on Module (SoM) contains the SoC, PMIC, DDR and OSPI flash.
Therefore, add support for the components present on the SoM.
Schematics: https://www.ti.com/lit/zip/SPRR463
TRM: http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
The FIT generated after the switch to using binman is using different
values for firmware and loadables properties compared to the old script.
With the old script:
firmware = "atf-1";
loadables = "u-boot", "atf-2", ...;
After switch to binman:
firmware = "u-boot";
loadables = "atf-1", "atf-2", ...;
This change result in SPL jumping directly into U-Boot proper instead of
initializing TF-A.
With this patch the properties change back to:
firmware = "atf-1";
loatables = "u-boot", "atf-2", ...;
Fixes: e0c0efff2a ("rockchip: Support building the all output files in binman")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add sha256 hash to FIT images when CONFIG_SPL_FIT_SIGNATURE=y.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL load FIT images by reading the data aligned to block length.
Block length aligned image data is read directly to the load address.
Unaligned image data is written to an offset of the load address and
then the data is memcpy to the load address.
This adds a small overhead of having to memcpy unaligned data, something
that normally is not an issue.
However, TF-A may have a segment that should be loaded into SRAM, e.g.
vendor TF-A for RK3568 has a 8KiB segment that should be loaded into the
8KiB PMU SRAM. Having the image data for such segment unaligned result
in segment being written to and memcpy from beyond the SRAM boundary, in
the end this results in invalid data in SRAM.
Aligning the FIT and its external data to MMC block length to work
around such issue.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
SOM itself from PS point of view is using the same configuration as K26
that's why reuse that files and only change compatible strings.
The reason for creating own set of files is just in case when versions
start to diverge because of HW change, supply chain issue, etc.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61f877ec0b480c5bd368a1211fc73ff7465016bd.1674043915.git.michal.simek@amd.com
When support for the Allwinner F1C100s SoC was originally introduced,
its DT lacked any MMC nodes, which upset our sunxi-u-boot.dtsi overlay,
when it tried to add an alias to the SD card. To quickly fix this back
then, we guarded that alias with a preprocessor macro.
Now the F1C100s family has gained MMC nodes, so we don't need the
special treatment anymore. Just remove this guard.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add the required binman images to replace the Makefile rules which are
currently used. This includes subsuming:
- tpl/u-boot-tpl-rockchip.bin if TPL is enabled
- idbloader.img if either or both of SPL and TPL are enabled
- u-boot.itb if SPL_FIT is enabled
- u-boot-rockchip.bin if SPL is used, either using u-boot.itb when
SPL_FIT is enabled or u-boot.img when it isn't
Note that the intermediate files are dropped with binman, since it
producing everything in one pass. This means that
tpl/u-boot-tpl-rockchip.bin is not created, for example.
Note that for some 32-bit rk3288 boards, rockchip-optee.dtsi is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable multiple-images so we can generate more than one image. Also
add a comment for the end of the #if block.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync the px30 dtsi from Linux kernel v6.1.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initial support for the PinePhone Pro has now landed upstream in
Linux 6.1 RC1 so sync the dts from 6.2-rc1 for initial support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RV1126 SoC.
Both eMMC and SD boot are tested in Edgeble Neu2 SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
This synchronizes the Device Trees related to Puma RK3399 SoM with Linux
kernel next-20221114 to include two important changes pertaining to
eMMC and SD card instability.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Sync the DT Files with linux kernel v6.1 and with commit a9b70102253ce
("ARM: dts: stm32: Add timer interrupts on stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The include file stm32mp1-clksrc.h is not necessary for the SCMI STM32MP15
dtsi files as the clock tree is not defined in the U-Boot SCMI device tree;
these SCMI device tree only support TFABOOT with stm32mp15_defconfig,
SPL with the basic boot defconfig is not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for USB2514B onboard hub on stm32mp157c EV1 board. The HUB
is supplied by a 3v3 PMIC regulator.
[backport from linux ad9591b01d24]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
phy-stm32-usbphyc bindings uses a connector node with vbus-supply
property.
[backport from linux 43e55d778a6b]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TI phy requires a reset before PHY address detection to make sure
correct strapping via MIO is detected. Facilitate the same using
ethernet-phy-id compatible string. GPIO reset entry will be added in
a separate commit.
This support is present in RevA but needs to be extended to RevB/1.0/1.1
versions which are built on top.
Fixes: 13622c7a9d ("arm64: zynqmp: Describe TI phy as ethernet-phy-id")
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6d500a83a787316353d4b26c75d1b51d29e3730e.1670854455.git.michal.simek@amd.com
The Cadence GEM/MACB driver now utilizes the platform-level reset on the
ZynqMP platform. Add reset definitions to the ZynqMP platform device
tree to allow this to be used.
Linux upstream commit (e461bd6f43f4e568f7436a8b6bc21c4ce6914c36).
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/14e3637735dbc626659e96d142f04a63398362f8.1670590595.git.michal.simek@amd.com
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
