Add default bootarguments with booting from mmc0 for this configuration.
This will allow a default Linux boot for this board.
Suggested-by: Jarvis Chen <jarvis.chen@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.
Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
This commit updates the default config with the values that are actually
used "in the wild" and which are close to what is used on the MediaTek
MT7688 based, 2nd generation of the GARDENA smart gateway:
- Reduce startup time by setting bootdelay to 0 (still allows accessing
the shell, one just has to send a key press quicker)
- Adjusting U-Boot environment volume names and MTD partitions to
the actual layout
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit eb5a2b6710 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.
Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Bump our py version to 1.10.0 to address CVE-2020-29651.
Reported-by: GitHub dependabot
Reported-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- rework sunxi DE2 driver and accompanying DW-HDMI platform driver
to drop redundant device specific code, and later use the DT as a
source of information
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYIQmGw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXKPqAJsGVBUQ1+vFaUrdGKtGZk8TOjtyKwCfe9vuH/E6
88T+ybssGrorMQwyOvQ=
=hyBc
-----END PGP SIGNATURE-----
Merge tag 'video-2021-07-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-video
- search for additional detailed timings in the EDID extension block
- rework sunxi DE2 driver and accompanying DW-HDMI platform driver
to drop redundant device specific code, and later use the DT as a
source of information
Currently DE2 driver uses functions which are defined in internal
headers. They are not meant to be used outside of uclass framework.
Switch DE2 driver to public ones. This has additional benefit that
device_probe doesn't need to be called manually.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is no real need to read source_id at probe time. It also doesn't
make sense to store it in driver private data since it's already stored
in class platform data. While this looks like cleanup (and it is), it's
also important for DE2 driver rework because this info will be filled
later (after probe is already executed).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
TV driver was never fully implemented. Remove search for it from DE2
driver.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
No Allwinner board with DW-HDMI controller use separate I2C bus for
EDID read. Remove that check.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are two ways how hot plug detection can be done.
One is standard way for DW HDMI controller - checking bit 2 in 0x3004
register. Another way is applicable only to Allwinner custom PHY - by
checking bit 19 in register 0x10038. Both methods are equally good as
far as we know.
Use standard method in order to reduce amount of custom code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
One of my monitors have only 4k@60 timing in base EDID block which is
out of range for devices with HDMI 1.4. It turns out that it has
additional detailed timings in CTA-861 Extension Block and two of them
are appropriate for HDMI 1.4.
Add additional search for valid detailed timing in extension block.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Code which searches for valid detailed timing entry will be used in more
places. Extract it.
No functional change is made. However, descriptors are casted to
edid_detailed_timing instead of edid_monitor_descriptor. Descriptor can
be of either type, but since we're interested only in DTD, it is more
fitting to cast to edid_detailed_timing.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When searching for detailed timing in EDID, check for digital display
earlier. There is no point parsing other parameters if this flag is not
present.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently driver accepts all resolution which won't work on 4k screens.
Add validation callback which limits acceptable resolutions to 297 MHz.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
commit cbea241e935e("efidebug: add multiple device path instances on Boot####")
slightly tweaked the efidebug syntax adding -b, -i and -s for the boot
image, initrd and optional data.
The pytests using this command were adapted as well. However I completely
missed the last "" argument, which at the time indicated the optional data
and needed conversion as well. This patch is adding the missing -s flag
and the tests are back to normal.
Fixes: cbea241e935e("efidebug: add multiple device path instances on Boot####")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In case of failure at efi_get_variable_int("BootOrder"), we should
skip examining boot option variables and return an appropriate error
code which is the one the function returned.
Fixes: CID 331153 Code maintainability issues (UNUSED_VALUE)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Indicated by Coverity Scan CID 331147
The ESRT was being refreshed in situations where the UpdateCapsule
procedure failed. In that scenario:
1) the ESRT refresh was superfluous.
2) a failed ESRT refresh return code overwrites the UpdateCapsule error
return code.
This commit ensures that the ESRT is only refreshed when the
UpdateCapsule performs successfully.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Tom Rini <trini@konsulko.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bumping the digest list count, for all supported algorithms, can be
calculated outside of the individual switch statements. So let's do that
for every loop iteration instead and simplify the code a bit.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To avoid diverging function definitions we need to include efi_loader.h.
Fixes: fe179d7fb5 ("efi_loader: Add size checks to efi_create_indexed_name()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to copy-paste error, two of the setexpr arguments were missing.
Add the missing arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide a man-page for the fatinfo command.
The .rst file was lost in patch 15d9694600 ("doc: fatinfo man-page").
Fixes: 15d9694600 ("doc: fatinfo man-page")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch adds support for the following I2C devices connected to
I2C bus 0 on the Octeon EBB7304:
- Dallas DS1337 RTC
- TLV EEPROM
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the AHCI compatible SATA DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
While porting from the Marvell source, I introduced a bug by misplacing
the parenthesis. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
