CF_SPI kconfig option defined twice with DM_SPI
and non DM_SPI.
Drop the non DM_SPI side kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Board gets reset when performing burst read/write operations. On the
other hand, no such behaviour is observed on small size operations.
In Linux, readl_poll_timeout API already adds delay of 1us which is
further skipped in U-boot. Hence, use new "readl_poll_sleep_timeout" API
which adds delay alongwith timeout functionality.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The guessed reason is that the existing logic of filling
tx fifo with data, rx fifo with NULL for tx transfer and
filling rx fifo with data, tx fifo with NULL for rx transfer
is not clear enough to support the Quad Page Program.
SiFive SPI controllers have specific sets of watermark
registers and SPI I/O directions bits in order to program
SPI controllers clear enough to support all sets of operating
modes.
Here is the exact programing sequence that would follow on this
patch and tested via SPI-NOR and MMC_SPI.
- set the frame format proto, endian
- set the frame format dir, set it for tx and clear it for rx
- TX transfer:
fill tx fifo with data.
wait for TX watermark bit to clear.
- RX transfer:
fill tx fifo with 0xff.
write nbytes to rx watermark register
wait for rx watermark bit to clear.
read the rx fifo data.
So, this patch adopts this program sequence and fixes the existing
I/O direction bit.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller has a proto bit field in frame format
register which would be used to configure the SPI I/O protocol
lines used on specific transfer.
Right now the driver is configuring this proto using slave->mode,
for all types of transctions. This makes the driver unable to
function since the proto needs to configure dynamically for
each and every transaction separately at runtime.
Now, the controller driver supports per transfer via spi-mem
exec_opo, so add the fmt_proto flag and fill the per transfer
buswidth so that the controller configures the proto bit at
runtime.
This patch fixes the SPI controller works with SPI NOR flash
on quad read with page program.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller is responsible to handle the
slave devices like mmc spi and spi nor flash.
The controller is designed such a way that it would
handle the slave transactions based on the I/O protocol
numbers, example if spi nor slave send quad write opcode
it has to send alone with I/O protocol number of 4 and
if it try to send data it has to send I/O protocol number
along with 4 line data.
But the current spi-xfer code from spi-mem is combining
the opcode and address in a single transaction, so the
SPI controller will be unable to identify the I/O protocol
number of opcode vs address.
So, add the spi-mem exec_op with spi-xfer of opcode, address
and data as a separate transaction. This doesn't remove
the .xfer of dm_spi_ops since mmc spi will make use of it.
Note: This code might have moved to the spi-mem core area
once we have done the dedicated tests on other controllers
and have real reason to move.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Usually variable name slave is used for spi_slave structure
and slave_plat for the dm_spi_slave_platdata.
Let's follow this meaningful notation by replacing slave
with slave_plat for dm_spi_slave_platdata structure.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit: 0ebb261a0b2d ("spi: spi-mem: Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum")
in linux.
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
This also fixes a bug identified with the atmel-quaspi driver.
The spi-nor core, when erasing sectors, fills the spi_mem_op template
using SPI_MEM_OP_NO_DATA, which initializes all the data members with
value zero. This is wrong because data.dir is treated as SPI_MEM_DATA_IN,
which translates in our driver to read accesses for erases (RICR), while
the controller expects write accesses (WICR).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.
Tested on u-boot-ti/next.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To support the SPI MEM API, instead of modifying the existing U-Boot
driver, this patch adds a port of the existing Linux driver.
This also has the advantage that porting changes and fixes from Linux will
be easier.
Porting of driver left most of the functions unchanged while few of the
changes are:
-Remove lock(mutexes) and irq handler as u-boot is a single core execution.
-Remove invalid masterid as it was required specially for multicore
execution in LS2088ARDB which is not the case in u-boot.
-Remove clock support as changing spi speed is not supported in uboot and
nor in linux.
Currently tested on LS1088ARDB, LS1012ARDB, LS1046ARDB, LS1046AFRWY,
LS1043AQDS, LS1021ATWR, LS2088ARDB, I.MX6ULL EVK.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The build currently fails with
drivers/spi/mpc8xxx_spi.c:64:3: warning: implicit declaration of function ‘dev_err’ [-Wimplicit-function-declaration]
...
drivers/spi/built-in.o: In function `mpc8xxx_spi_set_speed':
drivers/spi/mpc8xxx_spi.c:227: undefined reference to `dev_err'
Fixes: 4856cc7a97 (mpc8xxx_spi: implement real ->set_speed)
Fixes: 1a7b462dee (mpc8xxx_spi: put max_cs to use)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This Tegra QSPI driver hadn't been brought up to date with how
DM drivers are fetching data from the FDT now, and was pulling
in bogus data for base, max freq, etc. Fixed ofdata_to_platdata
to work the same way it does in the tegra114 SPI driver, using
dev_read_ functions.
Signed-off-by: Tom Warren <twarren@nvidia.com>
When claim_bus was setting the clock, it reset the QSPI controller,
which wipes out any tap delays set by previous bootloaders (nvtboot,
CBoot for example on Nano). Instead of doing that in claim_bus, which
gets called a lot, moved clock setting to probe(), and set tap delays
there, too. Also updated clock to 80MHz to match CBoot. Now QSPI env
save works reliably again.
Signed-off-by: Tom Warren <twarren@nvidia.com>
claim_bus() is passed a udevice *dev, which is the bus device's parent.
In this driver, claim_bus assumed it was the bus, which caused the
'priv' info pointer to be wrong, and periph_id was incorrect. This in
turn caused the periph clock call to assign the wrong clock (PLLM
instead of PLLP0), which caused a kernel warning. I only saw the 'bad'
periph_id when enabling DEBUG due to an assert. Not sure how QSPI was
working w/this errant clock, but it was moot as QSPI wasn't active
unless you probed it, and that wasn't happening until I posted a patch
to enable env save to QSPI for Nano (coming soon).
Signed-off-by: Tom Warren <twarren@nvidia.com>
This feature should not be enabled in release but can be useful for
developers who need to monitor register accesses at some specific places.
Helped me identify a bug in u-boot, by comparing the register accesses
from the u-boot driver with the ones from its linux variant.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[jagan: use 16 bit array with tmp variable]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The sama5d2 QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 24c8ff4684 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Not all boards have the same CSB frequency, nor do every SPI slave
necessarily support running at 16.7 MHz. So implement ->set_speed;
that also allows using a smaller PM (i.e., 0) for slaves that do
support a higher speed.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There are a few problems with the current driver.
First, it unconditionally reads from dout/writes to din whether or not
those pointers are NULL. So for example a simple "sf probe" ends up
writing four bytes at address 0:
=> md.l 0x0 8
00000000: 45454545 45454545 05050505 05050505 EEEEEEEE........
00000010: 00000000 00000000 07070707 07070707 ................
=> sf probe 0
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53618 din 00000000 bitlen 8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 0FB536B8 bitlen 48
SF: Detected s25sl032p with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> md.l 0x0 8
00000000: ff000000 45454545 05050505 05050505 ....EEEE........
00000010: 00000000 00000000 07070707 07070707 ................
(here I've change the first debug statement to a printf, and made it
print the din/dout pointers rather than the uints they point at).
Second, as we can also see above, it always writes a full 32 bits,
even if a smaller amount was requested. So for example
=> mw.l $loadaddr 0xaabbccdd 8
=> md.l $loadaddr 8
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
02000010: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x400 6
device 0 offset 0x400, size 0x6
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 48
SF: 6 bytes @ 0x400 Read: OK
=> sf read 0x02000010 0x400 8
device 0 offset 0x400, size 0x8
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB53848 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000010 bitlen 64
SF: 8 bytes @ 0x400 Read: OK
=> md.l $loadaddr 8
02000000: 45454545 45450000 aabbccdd aabbccdd EEEEEE..........
02000010: 45454545 45454545 aabbccdd aabbccdd EEEEEEEE........
Finally, when the bitlen is 24 mod 32 (e.g. requesting to read 3 or 7
bytes), the last three bytes and up being the wrong ones, since the
driver does a full 32 bit read and then shifts the wrong byte out:
=> mw.l $loadaddr 0xaabbccdd 4
=> md.l $loadaddr 4
02000000: aabbccdd aabbccdd aabbccdd aabbccdd ................
=> sf read $loadaddr 0x444 10
device 0 offset 0x444, size 0x10
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 128
SF: 16 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 3031392e 30342d30 U-Boot 2019.04-0
=> mw.l $loadaddr 0xaabbccdd 4
=> sf read $loadaddr 0x444 0xb
device 0 offset 0x444, size 0xb
mpc8xxx_spi_xfer: slave spi@7000:0 dout 0FB536E8 din 00000000 bitlen 40
mpc8xxx_spi_xfer: slave spi@7000:0 dout 00000000 din 02000000 bitlen 88
SF: 11 bytes @ 0x444 Read: OK
=> md.l $loadaddr 4
02000000: 552d426f 6f742032 31392e00 aabbccdd U-Boot 219......
Fix all of that by always using a character size of 8, and reject
transfers that are not a whole number of bytes. While it ends being
more work for the CPU, we're mostly bounded by the speed of the SPI
bus, and we avoid writing to the mode register in every loop.
Based on work by Klaus H. Sørensen.
Cc: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Currently, max_cs is write-only; it's just set in
mpc8xxx_spi_ofdata_to_platdata and not otherwise used.
My mpc8309 was always resetting during an "sf probe 0". It turns out
dm_gpio_set_dir_flags() was being called with garbage, since nothing
had initialized priv->gpios[0] - our device tree used "cs-gpios"
rather than "gpios", so gpio_request_list_by_name() had returned 0.
That would have been a lot easier to figure out if the chip select
index was sanity checked, so rename max_cs to cs_count, and reject a
xfer with a too large cs index.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
When ich_spi_exec_op_hwseq() is called to erase a 4k block
(opcode = SPINOR_OP_BE_4K), it expects to find a length value in
op->data.nbytes, but that value is always 0. As a result, the while loop
is never executed and no erase is carried out.
Fix this by dropping the loop code entirely, only keeping the relevant
parts of the loop body.
See http://patchwork.ozlabs.org/patch/1222779/ for more detailed
background information and discussion.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
TI's AM654 SoC has a Cadence OSPI IP. Add a new compatible string for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add chip select number check in spi_find_chip_select().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
When two instances of AXI QSPI with flash are added and tested
simultaneously the spi driver operations are relocated twice.
As a result code is accessing addresses outside of RAM when
relocated second time which is causing a crash.
Tested on Microblaze.
Similar change was done in past by:
commit f238b3f0fb ("watchdog: dm: Support manual relocation for watchdogs")
commit 2588f2ddfd ("dm: sf: Add support for all targets which requires MANUAL_RELOC")
commit 1b4c2aa25b ("gpio: dm: Support manual relocation for gpio")
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Note, that the size is further divided into 'minus 1' while writing
into CTRLR1.
This change fixed two different read issues,
1. sf read failure when with > 0x10000
2. Boot from SPI flash failed during spi_flash_read call in
common/spl/spl_spi.c
Observed and Tested in
- Rockpro64 with Gigadevice flash
- ROC-RK3399-PC with Winbond flash
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Apollo Lake to the ICH driver. This involves adjusting the
mmio address and skipping setting of the bbar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In TPL we want to reduce code size and support running with CONFIG_PCI
disabled. Add special code to handle this using a fixed BAR programmed
into the SPI on boot. Also cache the SPI flash to speed up boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add this method so that the memory-mapped location of the SPI flash can
be queried.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Apollo Lake (APL) only supports hardware sequencing. Add support for this
into the SPI driver, as an option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel Fast SPI interface is similar to ICH. Add of-platdata support
for this using the "intel,fast-spi" compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This incorrectly shortens read operations if there is a maximum write size
but no maximum read size. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to store the mmio base in platdata. It reduces the amount of
casting needed. Update the code and move the struct to the C file at the
same time, as we will need to use with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use debug() instead of printf() to reduce code size and change a bool
return value to the use the 'bool' type. Also drop the global data
declaration since it not actually used. Finally, set the log category.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use dev_get_driver_data() to obtain the device type. It has the same
effect and is shorter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reduce the size of the probe function but putting this code into its own
function.
Also remove the assumption that the PCH is always a parent of the SPI
controller, as this is not the case APL platforms. Use driver model to
find the PCH instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is annoying to have some of the init code in a different part of the
file. Move ich_init_controller() to just above probe() to keep things
together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't normally need this on x86 unless the size of SPI flash devices is
larger than 16MB. This can be enabled by particular SoCs as needed, since
it adds to code size.
Drop the default enabling of this option on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have to have an xfer() method even if it does nothing. This
is not correct, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the SPI_FLASH_BAR for the ESPI controller of FSL, this entry
is missed by
commit 6d82517836 ("configs: Don't use SPI_FLASH_BAR as default")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Disable and free clock when remove driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When CONFIG_OF_PRIOR_STAGE is enabled, this workaround was needed
before device_bind_common assigned request numbers sequentially in the
absence of aliases.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
The Broadcom ARM implementations do not yet have a clock framework so
one can use a fixed clock as the root clock of the hsspi block. The
fixed clock does not have an "enable" routine, since it's always
enabled. So when we hit this issue, getting an ENOSYS return, do not
bail but continue initialization.
Similarly the block might already have been out of reset, say, when
we are booting from a SPI device. So if the reset signal is not configured
in the device tree, do not bail out and instead skip deasserting the reset.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Make the driver compatible with both big and little endian SOCs.
Replace big-endian calls with their raw equivalents, expect for
writing the command to FIFO. That still has to be in big-endian
format.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This IP exists in both MIPS and ARM cores, so we also
allow to use this driver on bcm6858 and bcm63158.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The write data size can be overwritten by writing to the IDATSZ
field of IPCR register. Since the driver always updates the IDATSZ
in page program operation. Set the LUT data size to 0 to align
the codes with iMX.
Signed-off-by: Ye Li <ye.li@nxp.com>
On latest iMX platforms like iMX7D/iMX6UL/iMX8MQ, the QSPI controller
is updated to have TDH field in FLSHCR register. According to reference
manual, this TDH must be set to 1 when DDR_EN is set. Otherwise, the TX
DDR delay logic won't be enabled.
Another issue in DDR mode is the MCR register will be overwritten in
every read/write/erase operation. This causes DDR_EN been cleared while
TDH=1, then no clk2x output for TX data shift and all operations will
fail.
Signed-off-by: Ye Li <ye.li@nxp.com>
After this patch the mxs_spi.c DM/DTS driver can be used at early SPL to
read payload from SPI-NOR memories.
It was necessary to adjust its name to 'fsl_imx_2{38}_spi' to match
requirements for SPL_OF_PLATDATA usage.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Without this change the DM/DTS version of mxs_spi driver doesn't reset the
SPI IP block in probe.
As a result this driver (when used solely on U-Boot proper) relies on reset
performed by mxs spi driver in SPL.
In the use case where eMMC is used in SPL as a boot primary device, the
mxs_reset_block() is not called at all and DM/DTS aware SPI driver in
U-Boot proper is malfunctioning.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change initializes proper member of struct driver -
platdata_auto_alloc_size instead of priv_auto_alloc_size, which is setup
twice.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add support for SPI synchronous write followed by read,
this is common interface call from spi-nor to spi drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
MXS_SPI driver now partially converted into driver-model,
so unmark the DEPRECATED option for the same.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
[jagan: update the commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In case spi_get_bus_and_cs callback is used, spi bus is first probed
then slave devices are probed. To avoid a data abort in soft_spi probe
function, we need to check that (slave != NULL).
If slave is NULL, cs_flags and clk_flags will be initialized with
respectively GPIOD_ACTIVE_LOW and 0.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The prescaler value computation can yield wrong result if given 0x1f at
the beginning: the value is computed to be 0x20, but the maximum value
the register can hold 0x1f, so the actual stored value in this case is
0, which is obviously wrong.
Set the upper bound of the value to 0x1f with the min macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
With the introduction of the new spi-mem model operations changed
slightly. The new spi-mem operations make things a bit easier to
handle for ich-spi flash interface. This patch converts the ich-spi
driver by using spi-mem operations.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on Intel CrownBay and MinnowMax
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix compiler warnings when building the driver for 64-bit]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Since u-boot has added the spi-mem framework and replaced
the spi-nor framework, the mtk_qspi is no longer compatible
with the new spi-nor driver.
Remove this driver along with replacing config item
with new mtk spi-nor driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
[jagan: squash related changes and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
