This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers. Fix the resulting array overflow.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For fsl-lsch3, IFC is binded with address within 32-bit at fist.
After u-boot relocates to DDR, CS1, CS3 can be binded to higher
address to support large space.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. LS2085a provides PCIE_LUT_DBG register rather than PCIE_LDBG
to show the link status, so the patch fixes it.
2. Increase the delay time to make sure that link training
has finished.
3. Return invalid value when accessing multi-function device
4. For LS2085a DBI_RO_WR_EN bit is cleared as default, so we
must set this bit before change DBI register value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit aed2fbef5e
"dm: serial: Tidy up the pl01x driver"
caused a regression on (real hardware) PL010 by omitting
to update the line control register when switching baudrate.
Fix this by inlining the missing write to the baud control
register.
Also renaming the set_line_control() function to
pl011_set_line_control() since this function is clearly
PL011-specific, and it won't suffice to call that to
set up line control.
Tested on the Integrator/AP hardware.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name "pch_gbe.%x" exceeds the limit of the name in the
'struct eth_device'. Rename it as just "pch_gbe".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Turn ioaddr into an unsigned long rather than a sized 32-bit variable.
While at it, fix a couple of pointer to integer cast size mismatch
warnings by casting through unsigned long going from pointers to
integers and vice versa.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.
>From section 9.4.1.8 of that manual:
Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.
0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.
In addition, Freescale application note AN2805 is also very clear that
this bit must be set.
This patch reverts a change introduced by commit
457caecdbc.
Testing Done:
Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:
fff9b774: 65 29 80 00 oris r9,r9,32768
Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.
Booted an image on a MPC8541 based board successfully.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
make the ldb_clock configurable through the new define
CONFIG_SYS_LDB_CLOCK. This is needed as the ldb clock is not
always 650000000, for example on the aristainetos2 board,
where the ldb clock derives from PLL5 clock.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Add driver model support to the designware driver. This reuses most of the
existing code except for some duplication in the probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
