Add support for following features:
- nand boot, with PMECC 2bit ECC for 512 bytes sector
- SPI flash boot
- SD card boot
- LCD support
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix -Wimplicit-function-declaration for at91_lcd_hw_init()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
these variables are curently defined in several config files but the
driver doesn't use them and defaults to hardcoded values in
nand_defs.h
It's interesting to be able to change this hardcoded valude when the
hardware is not using the default adress signals to drive ALE and CLE
and two configuration defines already exist for this purpose so use
them.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Several minor updates to the cm-t35 config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Add the flag to allow runtime enviroment variable modifications.
This is being added so that the board-name can be modified at runtime
to indicate either a panda(4430) or a panda-es(4460)
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Fix the device tree loading for panda(4430) and panda-es(4460)
Modify the board name if a 4460 panda or panda-es is detected
at run time.
In the findfdt add a check for the panda-es board name and load
the panda-es device tree blob.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
As part of a review of a recent patch to add a new AM335x board, Tom
found several duplicate and/or unused #defines.
This patch simply removes them.
The two affected configs have been recompiled to check nothing was
broken (from a compilation point of view !!)
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Mark Jackson <mpfj-list@mimc.co.uk>
Add 'optargs' variable to be set to additional kernel arguments, similar
to omap3*/am3* usage.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The IGEP COM AQUILA and CYGNUS are industrial processors modules with
following highlights:
o AM3352/AM3354 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Adds CPSW support to the TI814X EVM configured with
an ET1011C PHY in GMII mode.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
All these macros are completely unused by any code.
CONFIG_FPGA is not a bitfield anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.
Signed-off-by: Tom Rini <trini@ti.com>
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
Signed-off-by: Stefan Roese <sr@denx.de>
The v2013.04 release has this patch set included:
5cb48582 "Add architecture-specific global data"
With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.
This patch now uses the automatically generated struct size instead to
not run into this problem again.
Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!
Signed-off-by: Stefan Roese <sr@denx.de>
The redundancy related defines are only correct for NAND, so guard all
of that area with CONFIG_ENV_IS_IN_NAND
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move baseaddr to hardware.h to be shared between
configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Setup environment and enable netconsole.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
