Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner V3/Sochip S3 uses the same die with Allwinner V3s/S3L, but V3 comes
with no co-packaged DDR (DDR3 is usually used externally), and S3L comes
with co-packaged DDR3.
Add support for Allwinner V3/S3 chips by add SoC names to original V3s
choice, and allow to select DDR3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC uses a quite different memory map, also changes the
clocks quite a bit. This requires some changes to the SPL SPI routine,
which hardcodes these values so far.
Using the just introduced helper functions to determine base address
and SPI controller generation, we can cover some of these differences
easily.
The clock setup is different, so requires some explicit code changes
there (reset and clock gate in one register at a different address).
Also we need to change the pinmux function to use a different set of
pins that the H6 uses for SPI0.
Eventually we can enable the H6 to use SPI booting in Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that we can easily select an SoC specific SPI0 base address, adding
support for the Allwinner R40 is fairly trivial:
We set the base address, add this SoC to the ones that use PC23 and
enable it in Kconfig.
This allows booting from SPI flash on R40 boards.
Tested on a Bananapi M2 Berry with SPI flash connected to the header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPI is available in Allwinner A64 SoC, so enable it
globally in Kconfig.
- CONFIG_SPI
- CONFIG_DM_SPI
- CONFIG_DM_SPI_FLASH
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
So far USB was not enabled for the Allwinner H6 boards, as the PHY
driver was not ready and the clock gates were missing. Since this is now
fixed, let's add the PHY and the OHCI/EHCI drivers to the build, for
all existing H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a routine to program the timing parameters for DDR3-1333 DRAM chips
connected to the H6 DRAM controller.
The values were gathered from doing back-calculations from a register
dump, trying to match them up with the official JEDEC DDDR3 spec.
If in doubt, the register dump values were taken for now, but the JEDEC
recommendation were added as a comment.
Many thanks to Jernej for contributing fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Most of the boards we support with H3/H5 enable DRAM on-die termination,
which is consistent with the high DRAM clocks that are used.
Make it the default (like it's done for other similar platforms) instead
of defining it in each defconfig.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Most H3/H5 boards we support have the DRAM ZQ value set to 3881979,
which is also consistent with the default set for the R40.
Make this value the default on H3/H5 instead of 123.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A few sun8i platforms define specific default DRAM ZQ values, but they
are not taken in account because of MACH_SUN8I being used for the 123
default first.
Replace MACH_SUN8I with the list of platforms that don't have specific
DRAM ZQ values, to avoid overwriting the default for those that do.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
Allwinner 64-bit SoCs can use 4GiB DRAM chip, however their memory map
has only allocated 3GiB for DRAM, so only 3GiB of the DRAM is
accessible.
Add a Kconfig option for the maximum accessible DRAM.
For A80 it should be a much higher value (8GiB), but as I have no A80
device to test and originally U-Boot only supports 2GiB DRAM on A80, it
currently still falls under the 2GiB situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.
Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.
On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
"default" lines in Kconfig are processed in order, the first hit will
stop considering subsequent lines. In the case of the DRAM_ODT_EN symbol
that means that everything following the first two lines will never be
checked:
------------
config DRAM_ODT_EN
bool "sunxi dram odt enable"
default n if !MACH_SUN8I_A23
default y if MACH_SUN8I_A23
default y if MACH_SUN8I_R40
default y if MACH_SUN50I
------------
Assuming that the "default y" for the A64 and the R40 were a deliberate
choice, fix the Kconfig stanza to take this into account.
Also remove the now redundant lines from the respective defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: droped 'default n' on original change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # A64, R40
Tested-by: Chen-Yu Tsai <wens@csie.org> # A23
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Use the driver model for MMC and SATA, in preparation for CONFIG_BLK
defaulting to y.
Tested on A10 Cubieboard.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add proper and simple kconfig option for dram_sun8i_a83t.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a33.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a23.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun9i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun4i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun6i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for rsb.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
SUN6I_PRCM is also used for SUN8I and SUN9I, so
select the same on respective MACH types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for p2wi.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for prcm.c
instead of using MACH type on Makefile.
PRCM (Power/Reset/Clock Management) is considered as a
Multi-Functional Device, so used the same on Kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi
NEO2), which may not work properly at 1008MHz if the chip's quality is
not so good.
Lower the default CPUx frequency of H5 to 816MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.
Add code to setup simplefb for Allwinner DE2 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.
Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.
Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The eMMC controller for the A83T uses the new operating mode. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
