This function is used in the bootstage report which may be trigged in TPL
or TPL. Add a very basic implication of this function so that it builds.
There is no attempt to get the formatting right, since this would add too
much code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The ctype array is brought into the image, adding 256 bytes, when it is
unlikely to be needed. The extra code for %p is only present when DEBUG
is defined, so let's drop ctype as well unless DEBUG is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
The test did reads after writes but didn't check the value.
It probably was because the sandbox didn't implement the writeX/readX
functions.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Updated to use sandbox_set_enable_memio():
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This function assumes that the 'val' parameter has no masked bits set.
This is not defined by the function prototype though. Fix the function to
mask the value and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This function needs a prototype so that tests can use it. Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function writes to its address so the address should not be declared
as const. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Quite a few tests use addresses or hex values for comparisons. Add hex
output for test failures, e.g.:
0x55ca22fa == reg: Expected 0x55ca22fa (1439310586),
got 0x55ea22fb (1441407739)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the 3733MTs DDR configuration that is auto generated from
DDR_Regconfig tool.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added training support for LPDDR4 and DDR3L DDRs. Also added/changed
some register configuration to support all 3 DDR types
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Once the arch specific boot_prepare_linux completes, boards wants to
have a custom preparation for linux. Add support for a custom
board_prep_linux.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Expand SPL_MULTI_DTB_FIT to accommodate usb peripheral nodes being
added to support SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
Some configs are selected in Kconfig and is no longer needed in the
defconfig files. Some configs (power domain, ram) are never used.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Some drivers (clk, pinctrl, reset, ...) are necessary for reset of the
system, they should be always selected.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default p0led status and phy0 link polling for all boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
