current PHY initalization code (tftp timeouts all the time). This commit
temporarily disables PHY initalization sequence to make the networking
operational, until a fix is found.
A '3' got cut off in the formatting of the last patch to automatically
change the clock speed of the system clock on sequoia board.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
message. Use PVR to distinguish between the two variants, and print proper CPU
information.
Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
core complains and IDE drivers fails to work. Also, assigning zero to a BAR
was illegal according to PCI 2.1 (the later revisions seem to have excluded the
sentence about "0" being considered an invalid address) -- so, use a reasonable
starting value of 0x1000 (that's what the most Linux archs are using).
Alternatively, one might have fixed the calls to pci_set_region() individually
(some code even seems to have taken care of this issue) but that would have
been a lot more work. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
update setenv() function so that entering a NULL value for the
variable's value will delete the environmental variable
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Acked-by: Stefan Roese <sr@denx.de>
the v_mac variable in the smc91111 driver is declared as a signed char ...
this causes problems when one of the bytes in the MAC is "signed" like 0xE0
because when it gets printed out, you get a display like:
0xFFFFFFE0 and that's no good
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The AMCC Secquoia board has been changed in a new revision from using a
33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD
indicates the difference. This patch reads that bit and uses the correct
clock speed for the board. This code is backward compatable will all
prior boards. All prior boards will be read as 33.000.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.
Signed-off-by: Stefan Roese <sr@denx.de>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
In case that there is no memory based bad block table available the
function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
nand_block_bad() directly. When parameter 'getchip' is set to zero,
nand_block_bad() will not right shift the offset to calculate the
correct page number.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When using FDT Images, the length of an inital ramdisk was
overwritten (bug introduced by commit 87a449c8, 22 Aug 2006).
Patches by Timur Tabi & Johns Daniel.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Enable hush shell, environment in flash rather in EEPROM,
more user-friendly default environment, etc.
The simple EEPROM environment can be selected easily in the board
config file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* Cleaned up the CDS PCI Config Tables and added NULL entries to
the end
* Fixed PCIe LAWBAR assignemt to use the cpu-relative address
* Fixed 85xx PCI code to assign powar region sizes based on the
config values (rather than hard-coding them)
* Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
Signed-off-by: Andy Fleming <afleming@freescale.com>
This included some changes to common files:
* Add 8568 processor SVR to various places
* Add support for setting the qe bus-frequency value in the dts
* Add the 8568MDS target to the Makefile
Signed-off-by: Andy Fleming <afleming@freescale.com>
When bringing up u-boot on new boards, PHY support sometimes gets
neglected. Most PHYs don't really need any special support,
though. By adding a generic entry that always matches if nothing
else does, we can provide support for "unsupported" PHYs for the
tsec.
The generic PHY driver supports most PHYs, including gigabit.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
on some ITX boards, notably those with a revision 3.1 CPU.
Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Michael Benedict <MBenedict@twacs.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
