Arrays are not cleared entirely because ARRAY_SIZE
returns the number of elements in an array, not the size
in bytes.
This commit fixes the calls to memset by providing the
array size in bytes instead of the number of elements
in the array.
Signed-off-by: Francois Berder <fberder@outlook.fr>
`part` option is in hexadecimal, so information is missing in usage
documentation.
Callgraph for `part` parsing is :
do_load -> fs_set_blk_dev -> part_get_info_by_dev_and_name_or_num ->
blk_get_device_part_str -> hextoul (This is why it is hexadecimal)
Signed-off-by: Mickaël Tansorier <mickael.tansorier@smile.fr>
Reviewed-by: Yoann Congal <yoann.congal@smile.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
We only have serial as console option, and leaving this on turns on
SYS_CONSOLE_IS_IN_ENV which is also not true for these devices, leaving
an ugly
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
behind.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
CONFIG_SYS_BOOT_LOCKED means that a restricted boot environment will
be used. In this case, hab_auth_img_or_fail should be called to prevent
U-Boot to continue running when the fitImage authentication fails.
Fix the logic accordingly.
Additionally, select CONFIG_SYS_BOOT_LOCKED by default.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
After the refactor with conf- nodes in fitImage, overlaystring wasn't
didn't handle the new conf- nodes in FIT Booting. Fix get_overlaystring
to handle conf- nodes.
Fixes: 837833a724 ("environment: ti: Add get_fit_config command to get FIT config string")
Reported-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Adapt behaviour to Linux kernel driver.
The return value of gpio_request_by_name_nodev() was not checked before,
and thus in case 'rb-gpios' was missing in DT, rb.type was set to
ATMEL_NAND_GPIO_RB nevertheless, leading to output like this for
example (on sam9x60-curiosity with the line removed from dts):
NAND: Could not find valid ONFI parameter page; aborting
device found, Manufacturer ID: 0xc2, Chip ID: 0xdc
Macronix NAND 512MiB 3,3V 8-bit
512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 64
atmel-nand-controller nand-controller: NAND scan failed: -22
Failed to probe nand driver (err = -22)
Failed to initialize NAND controller. (error -22)
0 MiB
Note: not having that gpio assigned in dts is possible, the driver does
not override nand_chip->dev_ready() then and a generic solution is used.
Fixes: 6a8dfd5722 ("nand: atmel: Add DM based NAND driver")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Multiple revisions of the StarFive VisionFive 2 board exist. They can be
identified by reading their EEPROM.
Linux uses two differently named device-tree files. To load the correct
device-tree we need to set $fdtfile to the device-tree file name that
matches the board revision.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
minor bug fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUPKp4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreau8AgAzU6HgWvcwP+vZwa1yMKxztJ8dUBmcuIN
SlUOaSUVBMZlfhEXbJQ3zJ5blSv2GlvJ5b4IAPYpVns6KUCBlEub6YQ6qTthX3lu
D0xUKcJM0YZfGSg3lUiQewywQj3Cn8sesEBCAqiNrE00mFcvDnupUxnlZ+9R23H6
y192uQJv48Zw6Aq6cVhbTbauNfcq4QbN3SDTg24wTgq4Slg7Hu2Zn27GFJkA5W3o
ka0aJPMq5r1mRpmxy0qejoVy2XSM/2XiNJcnH2eymQTKdH6nFBXiXtse1gbe3uHH
wrzFHxL+2B25aVJNK+wDgeK9jcsz8V0W5WWtccr9hHpkZG6BtjCVMQ==
=h4sw
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-23sep23' of https://source.denx.de/u-boot/custodians/u-boot-dm
trace: correct format of flyrecord
minor bug fixes
dm tree enhancement
adjust meaning of bootph-pre-ram/sram
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUPQXURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY1TAf+LeDzKKMhJmyo5ImQWlKPdFt9UGlWqthL
PBngUWV7GdQ5Kn+dLmKmySAmnQC4XNid565nJt8okmMfpHYUBhOnrnJmrXTZdDPJ
lYrpEAR7fTyTTTwjSVFcIXJ56bIT07AUX6jQATh383+Plm0U15tRBMguNsrTy1wL
EmJBVdeT0BZkpSkJyqAIkVuwjOYP+KSuVCectL5LRIpKtjOA+HmMGmELUirjuL00
uN2h/uucuSGFnjCmKW4l9sYrxxYgd/zN2Y8SOJwBebKyHxSgyvNdbjZxeG5o3gSS
ruUSEx4DHYVIRHeDBAnwB4wLdCOqfC2dy0ACReTg0Li+iSQN9qYtEg==
=Sl3P
-----END PGP SIGNATURE-----
Merge tag 'dm-next-23sep23' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
buildman file-keeping and build-progress improvements
dm tree enhancement
adjust meaning of bootph-pre-ram/sram
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
The Kconfig and maintainer processing can take a while, sometimes 5
seconds or more. This skews the timing printed by buildmand when the build
completes. Start the clock when the threads start to avoid this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Make a list of common output extensions and use it to ensure that the -k
option preserves all of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The output from "dm tree" or "dm uclass" is a bit annoying
if the number of devices available on the system is huge.
(This is especially true on sandbox when I debug some DM code.)
With this patch, we can specify the uclass name or the device
name that we are interested in in order to limit the output.
For instance,
=> dm uclass usb
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 124: usb
=> dm tree usb:usb@1
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
If you want forward-matching against a uclass or udevice name,
you can specify "-e" option.
=> dm uclass -e usb
uclass 15: usb_emul
0 hub-emul @ 0bcffb00, seq 0
1 flash-stick@0 @ 0bcffc30, seq 1
2 flash-stick@1 @ 0bcffdc0, seq 2
3 flash-stick@2 @ 0bcfff50, seq 3
4 keyb@3 @ 0bd000e0, seq 4
uclass 64: usb_mass_storage
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 122: usb_dev_generic
uclass 123: usb_hub
0 hub @ 0bcff9b0, seq 0
uclass 124: usb
=> dm tree -e usb
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nodes with bootph-pre-sram/ram props are bound in multiple phases:
1. At TPL (bootph-pre-sram) or SPL (bootph-pre-ram) phase
2. At U-Boot proper pre-relocation phase
3. At U-Boot proper normal phase
However the binding and U-Boot Driver Model documentation indicate that
only nodes marked with bootph-all or bootph-some-ram should be bound in
the U-Boot proper pre-relocation phase.
Change ofnode_pre_reloc to report a node with bootph-pre-ram/sram prop
with a pre-reloc status only after U-Boot proper pre-relocation phase.
Also update the ofnode_pre_reloc documentation to closer reflect the
binding and driver model documentation.
This changes behavior of what nodes are bound in the U-Boot proper
pre-relocation phase. Change to bootph-all or add bootph-some-ram prop
to restore prior behavior.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set CONFIG_SYS_LOAD_ADDR=0x88000000 and use this address for
loading fitImage.
Also pass the standard CONFIG_BOOTFILE option to indicate
the fitImage file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Trying to boot a fitImage after a successful hab_auth_img operation
causes the following error:
## Loading kernel from FIT Image at 88000000 ...
Using 'conf-imx7d-smegw01.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x8800010c
Data Size: 9901752 Bytes = 9.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80800000
Entry Point: 0x80800000
Hash algo: sha256
Hash value: 28f8779bbf010780f16dd3d84ecb9b604c44c5c2cf7acd098c264a2d3f68e969
Verifying Hash Integrity ... sha256Error in SEC deq
CAAM was not setup properly or it is faulty error!
The reason for this error is that the BootROM uses the CAAM Job Ring 0,
so disable its node in U-Boot to avoid the resource conflict.
imx8m dtsi files also have the Job Ring 0 disable since the following
kernel commit:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch?h=v6.5&id=dc9c1ceb555ff661e6fc1081434600771f29657c
For a temporary solution, disable the Job Ring 0 in imx7s-u-boot.dtsi.
Reported-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ivt_offset parameter is optional for both hab_auth_img_or_fail
and hab_auth_img commands.
Document it in their usage texts to make it clearer.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit ea91031b22 ("imx: hab: extend hab_auth_img to calculate
ivt_offset"), it is possible to call the hab_auth_img command without the
last ivt_offset argument.
Currently, calling hab_auth_img_or_fail without the last
ivt_offset parameter causes a failure and the command usage text is shown.
Fix this problem by adjusting the argc logic to allow
calling hab_auth_img_or_fail with only the address and size parameters.
This way, both hab_auth_img and hab_auth_img_or_fail have the same
behavior with respect to the allowed number of command parameters.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
If CMD_ELF disabled and IMX_BOOTAUX enabled, the u-boot building ends
up with a linking error [1]. Select LIB_ELF to fix the building
issue.
[1]
ld: /tmp/ccaF1rpv.ltrans0.ltrans.o: in function `do_bootaux':
arch/arm/mach-imx/imx_bootaux.c:108: undefined reference to `valid_elf_image'
Fixes: c0f037f6a2 ("mach-imx: bootaux: elf firmware support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Current alignment which is using 16 bytes is not correct in connection to
trace_clocks description and it's length.
That's why use start_addr variable and record proper size based on used
entries.
Fixes: be16fc81b2 ("trace: Update proftool to use new binary format").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Flyrecord tracing data are page aligned that's why it is necessary to
calculate alignment properly. Because trace_clocks description is the part
of record length it is necessary to have information about length earlier.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
tputq() requires variables to have 64bit width that's why make them 64bit
to clean alignment requirement.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
People may put their user name and email in a local config file and
reference it by the include.* directives, however `git config --global`
doesn't look up the included configs by default.
Enable the --includes option explicitly to support such use cases.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reproduct warning:
$ git clean -dfx
$ make CROSS_COMPILE="" qemu-x86_64_defconfig
$ make -j8
...
u-boot/tools/binman/etype/section.py:25:
SyntaxWarning: invalid escape sequence '\('
"""Entry that contains other entries
Signed-off-by: Rong Tao <rongtao@cestc.cn>
With Python versions older than 3.9 Buildman produces an error on
start-up. Fix this with a workaround for importlib.
There is already a workaround for v3.6 but I am not sure if that is still
functioning.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no "run_patman" procedure in patman's __main__.py file, which
would cause the following error at execution:
"AttributeError: module 'patman.__main__' has no attribute 'run_patman'"
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vanessa's NXP e-mail is no longer active.
Contacted her offline and she told me that she does not have
access to the board anymore and it is OK to remove her
from MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Errors were handled only if an I2C transfer timed out
and received a NACK which is very unlikely. This commit
changes the condition such that errors are handled if
an I2C transfer times out or received a NACK.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
The NETSEC GMAC occasionally falls into a weird state where
MAC_REG_DESC_SOFT_RST has never been cleared and shows errors like the
below when networking commands are issued:
=> ping 192.168.1.1
ethernet@522d0000 Waiting for PHY auto negotiation to complete... done
netsec_wait_while_busy: timeout
Using ethernet@522d0000 device
ARP Retry count exceeded; starting again
ping failed; host 192.168.1.1 is not alive
It happens on not only 'ping' but also 'dhcp', 'tftp' and so on.
Luckily, restarting the NETSEC GMAC and trying again seems to fix the
problematic state. So first ensure that we haven't entered the state by
checking MAC_REG_DESC_SOFT_RST to be cleared; otherwise, restarting
NETSEC/PHY and trying again would work as a workaround.
Signed-off-by: Ryosuke Saito <ryosuke.saito@linaro.org>
Tested-by: Masahisa Kojima <masahisa.kojima@linaro.org>
commit 280f45d239 ("configs: get rid of build warnings due to
SPL_USB_DWC3_GENERIC") missed enabling DWC3 glue layer for
usbmsc_defconfig and this broke boot from USB mass storage.
Fix this by enabling DWC3 glue layer.
Fixes: 280f45d239 ("configs: get rid of build warnings due to SPL_USB_DWC3_GENERIC")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Make sure to stay within bounds, as a misbehaving HTTP server
can trigger a buffer overflow if not properly handled.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Fix a bug of missing setting size of initrd in pxeboot
- Allow Python packages to be dropped
- Reland "x86: Move FACP table into separate functions"
- Fixes for chromebook_link64 and chromebook_samus_tpl
- Fixes and improvements for coreboot
- x86 documentation updates
-----BEGIN PGP SIGNATURE-----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=+q36
-----END PGP SIGNATURE-----
Merge tag 'x86-pull-20230922' of https://source.denx.de/u-boot/custodians/u-boot-x86 into next
- Add bootstd support to 64-bit efi payload
- Fix a bug of missing setting size of initrd in pxeboot
- Allow Python packages to be dropped
- Reland "x86: Move FACP table into separate functions"
- Fixes for chromebook_link64 and chromebook_samus_tpl
- Fixes and improvements for coreboot
- x86 documentation updates
Add a little more detail as to why coreboot64 is preferred for booting
Linux distros.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move this out of the main file since for simple users it is easier to
rely on standard boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Refresh the summary information so it is more up-to-date. Add links to
the coreboot and slimbootloader docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is enough material that it makes sense to split this up into
several files. Create an x86/ directory for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make a note of where coreboot installed the SMBIOS tables so that we can
pass this on to EFI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot should set up the SMBIOS tables during startup, as it does on x86.
Ensure that it does this correctly on non-x86 machines too, by creating
an event spy for last-stage init.
Tidy up the installation-condition code while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remember where these end up so that we can pass this information on to
the EFI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>