This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
- As there are no boards that use different values for speed / slave on
different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
common to all users.
- Convert all remaining symbols to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
commit 0cfccb5401 ("configs: Resync with savedefconfig")
removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig
files, whicih would block the use case of system loading rootfs
from USB drives, add them back.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move ADDR_MAP related config options from include/configs/*.h to the
proper place in lib/Kconfig. This has been done using
./tools/moveconfig.py and manual inspection of the generated changes.
This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4
board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity
mapping limit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add device tree for P5040DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
This converts the following to Kconfig:
CONFIG_NAND
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
