Commit graph

25 commits

Author SHA1 Message Date
Masahiro Yamada
079b54f29e ARM: uniphier: enable CONFIG_PINCONF
Enable the pin configuration feature for UniPhier 64 bit SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-08 10:25:15 +09:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
7c8f00e484 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-10 20:29:02 -05:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Masahiro Yamada
7d8cca7be6 ARM: uniphier: enable HS200 support for uniphier_v8_defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-28 06:32:50 +09:00
Masahiro Yamada
3281532ab2 ARM: uniphier: enable CONFIG_MMC_SDHCI_SDMA for ARMv8 SoCs
I did not enable SDMA when I added sdhci-cadence support because LD20
boards are equipped with a large amount memory beyond 32 bit address
range, but SDMA does not support the 64bit address.  U-Boot relocates
itself to the end of effectively available RAM.  This would make the
MMC enumeration fail because the buffer for EXT_CSD allocated in the
stack would go too high, then SDMA would fail to transfer data.

Recent SDHCI-compatible controllers support ADMA, but unfortunately
U-Boot does not support ADMA.

In the previous commit, I hided the DRAM area that exceeds the 32 bit
address range.  Now, I can enable CONFIG_MMC_SDHCI_SDMA.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-01-09 21:58:18 +09:00
Masahiro Yamada
7e3caa81e0 Move CONFIG_PANIC_HANG to Kconfig
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26 13:10:24 -05:00
Tom Rini
7af2e3648f configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-18 20:19:09 -05:00
Masahiro Yamada
53c149c3a5 ARM: uniphier: set CONFIG_LOGLEVEL to 6
Print out KERN_NOTICE or higher level log messages.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Adam Ford
8daec2d9d3 net: Add SMC911X driver to Kconfig, convert
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 21:40:26 -04:00
Masahiro Yamada
d37d31849c ARM: uniphier: enable DWC3 xHCI driver
Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Adam Ford
e3f24d4f2c Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is set
Add the following options to drivers/misc/Kconfig:
	SYS_I2C_EEPROM_ADDR
	SYS_I2C_EEPROM_BUS
	SYS_EEPROM_SIZE
	SYS_EEPROM_PAGE_WRITE_BITS
	SYS_EEPROM_PAGE_WRITE_DELAY_MS
	SYS_I2C_EEPROM_ADDR_LEN
	SYS_I2C_EEPROM_ADDR_OVERFLOW

This does not migrate any boards, but provides a foundations for
those who want/need these options

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate uniphier]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-02 15:50:30 -04:00
Masahiro Yamada
0cc0c544bc ARM: uniphier: enable Denali NAND driver for 64bit SoCs
Now the entry to the NAND driver init can be is controlled by DT;
it should not hurt to compile the driver all the time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Masahiro Yamada
a3f54bc74f ARM: uniphier: enable CONFIG_CMD_FS_GENERIC
Enable file system commands such as load, ls.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-07-26 22:27:15 +09:00
Masahiro Yamada
fed9c76641 ARM: uniphier: enable PSCI sysreset for uniphier_v8_defconfig
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31.  Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20 23:49:50 +09:00
Tom Rini
8728c97eff configs: Re-sync
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13 13:52:33 -04:00
Masahiro Yamada
2af94aafa5 ARM: uniphier: enable CONFIG_CMD_CONFIG
This command is useful to see which config options are enabled on
the running U-Boot image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:39:48 +09:00
Masahiro Yamada
c05a59d294 ARM: uniphier: enable CONFIG_CMD_GPT
Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the
SPL for UniPhier platform does not recognize any partitions.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
5c8c6da132 ARM: uniphier: disable CONFIG_MTD_NOR_FLASH
This feature is seldom used these days on UniPhier boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
1b280978c0 ARM: uniphier: enable generic EHCI driver for uniphier_v8_defconfig
The LD11 SoC is equipped with USB EHCI controllers.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
e856bdcfb4 flash: complete CONFIG_SYS_NO_FLASH move with renaming
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12 14:30:25 -05:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Masahiro Yamada
82b3d98b3a ARM: uniphier: add uniphier_v8_defconfig
This defconfig does not support SPL.  If you use this, the basic
SoC initialization must be done in firmware that runs before U-Boot.
(Generally, ARM Trusted Firmware is expected to do this job).

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 15:15:22 +09:00