Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
imx6qdl_icore_mmc_defconfig => imx6qdl_icore_rqs_defconfig
Since icorem6_rqs support MMC/eMMC boot, so doesn't need
to name it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no need to add a 100us delay after the DDR initialization.
Other imx6 boards do not have such delay either, so simply remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.
This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
from the number of CSs
HWS_TIM_1T - enforce 1t
HWS_TIM_2T - enforce 2t
This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not a very useful name since once it is probed it still hangs
around. With driver model we will use uclass data for this, so rename the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The instructions for creating a disk image that are presently in
README.sandbox fail because sfdisk doesn't know about GPT.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Enable all the boot-on regulator in default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Probe dwc2 udc in the function of board_usb_start to enable
usb gadget function.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The bank0 ram size should be the DRAM size minus reserved size,
the DRAM size may be 1GB, 2GB, 4GB, we can not hard code it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added DECLARE_GLOBAL_DATA_PTR for RK3328, RK3368 and RK3399:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
K2G ICE evm will have its own dtb. Therefore, add it to the list of dtbs
located in the appended U-boot dtb FIT image. Therefore, when swapping out
dtbs K2G ICE boards can grab the correct one.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Certain peripherals used by K2G GP aren't used on K2G ICE evm. Or
configuration is slightly different. Therefore, use board detection to
deal with these variations.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some code doesn't apply to K2G ICE evm. Therefore, use board detection to
wrap these calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration settings used by the K2G ICE evm. Also use board
detection to determine which DDR3 configuration to use.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.
Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a function that can be used to determine if the board being ran on is
a K2G Industrial Communication Engine EVM or K2G General Purpose EVM based
on values programmed on the EEPROM.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some K2G evms have their EEPROM programming while most do not. Therefore,
add EEPROM board detection to be used as the default method and fall back
to the alternative board detection when needed.
Also reorder board configuration. Perform bare minimal configuration
initially since board detection hasn't ran. Finish board configuration
once the board has been identified.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now with support for U-boot runtime dtb selection each board needs to
define board_fit_config_name_match so U-boot can determine what the
correct dtb is within the FIT blob.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For K2G, runtime DTB selection utilizes the embedded_dtb_select function.
Therefore, define the function which will perform a EEPROM read and then
retries selecting the correct dtb now that it can detect which board its
on. For other Keystone devices use an empty function since they will still
use the embedded FIT functionality but their FIT will only contain a single
dtb.
Most production K2G boards do not have their EEPROM programmed. Therefore,
perform a test to verify a K2G GP is currently being used and if it is then
set the values normally set by a EEPROM read.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It's been a while since I've touched U-Boot on the Raspberry Pi and
other things have been taking my time. Drop my maintainership for this
port.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The 82xx board mgcoge3ne was removed from the codebase, so this is dead
code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Discern the SoMs based on the presence of SPI flash to support both
variants of the SoM, one booting from SPI NOR and one booting from
eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Continue loading U-Boot from MMC2 when the SPL was loaded using SAM-BA
loader. This allows the board to boot system from the removable media
instead of the eMMC, which is useful for commissioning purposes. When
booting from the eMMC, always boot from it as it is not possible to
boot from the SD interface directly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SDHCI1 is the primary boot controller on rev. 2.1 SoM, which
is the version available on the market. Swap the controller order
to match this and future versions of the SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Init the controllers, otherwise the board cannot boot from SD/MMC.
This boot option is new on rev. 2.1 SoM .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The CAN controllers need slight delay between toggling of their reset
line. Move this action into board_init(), otherwise timer will not be
initialized and the board might hang.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
According to the datasheet, sequential mapping is used for DDR
SDRAM, while interleaved mapping is used for regular SDRAM.
Incorrect configuration of this bit does indeed cause sporadic
memory instability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit 842778a091 dfu-util shows serial="UNDEFINED".
to see here again a serial number, we have to call
g_dnl_set_serialnumber().
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Otherwise the loaded image would miss the efi_runtime sections, and fall
over hard when grub (for example) tried to call runtime services located
in this section.
Signed-off-by: Rob Clark <robdclark@gmail.com>
On the controlcenterd_36BIT_SDCARD config we get a warning about
prg_stage1_prepare being unused. Move the declaration closer to usage
and hide under the existing #if tests.
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init* contain sleep.h header which is not present in u-boot.
Instead of keep comment sleep.h in psu_init* it is easier to add empty
file which is included.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brxre1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages under the condition board_is_bone().
But this is true only for BeagleBoneWhite. Due to which voltages
are not configured for BBB, BBW as wrong device is being probed.
So create a common function board_is_beaglebonex() which includes
am335x based beagle family. Use this for updating voltages.
Also remove extra if condition for selecting voltages which is
done later using a switch case and match usb current limit as
before the commit 0650798824.
Fixes: 0650798824 ("board: am335x: Introduce scale_vcores")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
