Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable LZO compression of the multi-DTB fitImages, since the U-Boot
with multiple DTs enabled is becoming quite large and the DTs can
be well compressed. The LZO compression saves almost 200 kiB on the
Salvator-X(S) and ULCB targets.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add required Kconfig symbols, Makefile bits and macro fixes in a
few places to support LZO and DT compression in U-Boot. This can
save a lot of space with multi-DTB fitImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Allow enabling both LZO and GZIP DT compression in SPL and fix a
bug where if the GZIP decompression failed, the LZO decompression
would not even be attempted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Save these registers for
future use.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split fdtdec_setup_memory_banksize() into fdtdec_setup_memory_banksize_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_memory_banksize(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Split fdtdec_setup_mem_size_base() into fdtdec_setup_mem_size_base_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_mem_size_base(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case the gunzip() call fails, it will print an error message.
If that happens within the YModem session, the error message will
not be displayed and would be useless. Move the gunzip() call out
of the YModem session to make those possible error messages visible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
In case spl_parse_image_header() errors out, terminate the YModem
session, otherwise we won't get any further output.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.
It fixes the following build failure:
./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
when building the host tools with gcc 4.7.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix missing at91 boards and split the at91 in two categories:
at91 arm v7
at91 arm926esj
which are the two main cores for the at91 architecture.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.
Remove them to clean u-boot source code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.
Make this step explicit in the instructions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use a single '=' to test string equality for compatibility with non-bash
shells. Otherwise, if /bin/sh is dash, build fails:
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
- pico-imx6ul: fix after conversion
- engicam boards
- pico-imx7d _ README due to hang with imx-usb-loader
-----BEGIN PGP SIGNATURE-----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=TWtH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190401' of git://git.denx.de/u-boot-imx
Fixes for 2019.01
- pico-imx6ul: fix after conversion
- engicam boards
- pico-imx7d _ README due to hang with imx-usb-loader
Since commit 9e3c0174da ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Add such recommendation to the README file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.
Fixes: 4eb9aa3935 ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.
So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <aford173@gmail.com>
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcnoA9AAoJECaAFcEOcohNRYYH/0SAGKro+gO1q07xpBLGbOSL
MJPNDQ853IpH+kI+Mc+VFeFZz8fuQHae2aKfgmHmEGGSygFqAKXvMUgG73XO8Z27
Ov9r0RgR5s35eXFC0URqcDSCuTtFSP/MdmSy2hO546pJOapHhmx/eZUId3ZFjSe5
puIQfTxK0zbNqfFlfjsRnkXhR9jhYVvPtSpFYYjCeU/dRB4/OUzNHQjwjkdB8ru1
mTLmrhqqZ4fq3t9JMrxCH3COvI6QYBXj73ynKYtJ4lByh3NdIz0a37F99FiWgH2X
0WptUN8tjjZP+2BboVNo6io/12YxE6V+wG2LGEXreS9ubMr4nm+LXqDCoZIB7MM=
=ESBv
-----END PGP SIGNATURE-----
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
The I2C bus number to access the PMIC is I2C 7, fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Activate I2C7 on Alt to allow access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit d245059ff7 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff7 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
The PHY LED mode register mask should be 0xc000 , not 0xc0000.
Correct the mask to operate on the right bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
