This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Cleanup: Remove custom flash driver for 8 bit boot-eprom and replace it with
the FLASH_CFI_LEGACY et al. config options.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
The taihu board used gpio_read_out_bit which reads the output register and not
the pin state.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
Call fdt_fixup_memory() on the boards TQM5200, TQM5200_B, TQM5200S,
TB5200 and TB5200_B to fixup the /memory node with the memory values
detected by U-Boot.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Call fdt_fixup_memory() on the boards TQM5200, TQM5200_B, TQM5200S,
TB5200 and TB5200_B to fixup the /memory node with the memory values
detected by U-Boot.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
This patch fixes a bug in the SDRAM initialization code for the
TQM5200. The hi_addr bit is now set correctly. Without this patch
the hi_addr bit is always set to 1, if the second SDRAM bank is
not populated.
For other MPC5200 boards a correspondig patch has already been applied
some time ago, see commit a63109281a.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
--
Forget the first patch please. I confused flash with SDRAM in
the comment ...
Back in commit a551cee99a
(86xx: Fix GUR PCI config registers properly), we should have
changed the MPC86xx_PORBMSR_HA and MPC86xx_PORDEVSR_IO_SEL
symbols in the sbc8641d board as well. Fix this oversight.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Don't include testdram() on NAND-booting target acadia_nand. This saves
a few bytes and makes the target build clean again.
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux commit fac8b209b1084bc85748bd54e13d00c1262b220f ("Remove
final traces of long-deprecated "ramdisk" kernel parm") makes these
changes neccessary.
Signed-off-by: Detlev Zundel <dzu@denx.de>
- Fix flash_init call when CFG_NO_FLASH is used
- Remove no more needed flash.c for qemu-mips
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Back in commit 975a083a5e where
I tried to "8610HPCD: Fix typos in two PCI setup registers", I
botched it due to not realizing that 8610 and 8641 had different
Global Utility Register defintions, one of which was like 85xx,
and the other wasn't. Correct this problem by introducing two
symbols, one for each 86xx SoC, but neither of which is named
anything like 85xx.
My bad. Lovely Wednesday with git bisect. You know.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The two symbols MPC86xx_PORDEVSR_IO_SEL and MPC86xx_PORBMSR_HA
were erroneously present as 85xx names and values, leftover from
the clone wars. Fix this by removing the 85xx cruft from the
86xx codebase.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The option CONFIG_I2C_MULTI_BUS does not have any effect on Sequoia, the
PPC440EPx reference platform, because IIC1 is never enabled. Add Sequoia board
code to turn on IIC1 if CONFIG_I2C_MULTI_BUS is selected.
Signed-off-by: Mike Nuss <mike@terascala.com>
Cc: Stefan Roese <sr@denx.de>
