Commit graph

87134 commits

Author SHA1 Message Date
Lukasz Majewski
70b4d610f8 dts: xea: Add u-boot specific 'type' property to duart
The DM_SERIAL implicitly requires CONFIG_PL01X_SERIAL, which
allows support for both serial IP block versions (i.e. PL011 and
PL010).

The decision about used IP block is based on the compatible string,
when DM is used.

In the XEA, the OF_PLATDATA is used to allow usage of serial driver in
the SPL (as the size of SPL is crucial). In this case one cannot extract
the type of IP block from .data field (corresponding to compatible) and
it must be explicitly read at probe from dtoc generated, u-boot specific
property.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
9a1efecb2c dts: xea: Enable debug UART support in XEA's SPL (DM_SERIAL)
After enabling DM_SERIAL for XEA board, the same serial shall be used
in the SPL (with SPL_OF_PLATDATA support).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
9c2eefaf0d spl: xea: Provide stub DM driver for imx28 clocks
This code fixes following WARNING:
  DTOC    spl/dts/dt-plat.c
fsl_imx28_clkctrl: WARNING: the driver fsl_imx28_clkctrl was not found in the driver list

As imx28 doesn't yet support common clock framework, this prevents from
DTOC warnings during SPL build.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
11194c0d11 defconfig: xea: Change default spi-nor memory bus to 2
After the re-sync with Linux kernel (v6.0) of the XEA DTS
(SHA1: 7d08ddd09b) the alias
for SPI bus, to which SPI-NOR  memory is connected, has changed from
'spi3' to 'spi2'.

To be in sync with current u-boot's xea dts, the default bus number
(which allows running 'sf probe' without any extra parameters given)
has been adjusted.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
c5e8c336ec dts: xea: Provide missing FEC required properties (mac0 and reg_fec_3v3)
After the commit (SHA1: 7d08ddd09b) some
u-boot specific XEA FEC related properties have been replaced by ones
from the Linux kernel.

To be more specific - XEA board (and imx287 in general) has built L2
switch connected to FEC, which needs some special treatment.

In u-boot it is handled with 'mac0' node, whereas Linux uses dedicated
switch DTS node.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
0d30b6c4ec dts: xea: Delete not used in u-boot DTS nodes
After the re-sync with Linux Kernel's DTS
(SHA1: 7d08ddd09b), the XEA's
descripion has nodes and properties, which are NOT utilized
in the u-boot.

To avoid confusion - those are deleted.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Emanuele Ghidoli
611b94bf69 toradex: tdx-cfg-block: add 0070 verdin i.mx 8m plus quad sku
Add new i.MX 8M Plus Quad SKU to ConfigBlock handling.

0070: Verdin iMX8M Plus Quad 8GB WB IT

This SKU is identical to 0066 but supporting Industrial Temperature range.

Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
e7c1c0811b arm: config: Adjust imx287 based XEA board PMU configuration
This patch adjusts XEA's PMU setup as this board is supposed to be
mainly powered from DCDC_BATT source.

Moreover, in this HW design the VDD_4P2 is not used as well.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
301c6e6e69 arm: mxs: Add function to dump PMU registers
This commit provides function, which when debugging
output is enabled dumps the IMX28 PMU registers.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
79230640cb arm: mxs: Provide Kconfig option to not enable 4P2 regulator in IMX28 PMU
The IMX28 PMU (Power Management Unit) has a dedicated Linear Regulator
to produce (by default) 4.2V output - available outside the chip as
VDD_4P2.

When system is supposed to not use VDD5V as a main power source - instead
the DCDC_BATT is used; it is safe to disable this regulator.

As the in-PMU DCDC switching regulator (from which DCDC_VDDA, DCDC_VDDIO
and DCDC_VDDD are generated) can be driven from DCDC_BATT or output
of this 4P2 regulator - by disabling the latter the use of the DCDC_BATT
is forced.

To be more specific - according to NXP's AN4199 the DCDC_BATT source is
preferred (over VDD5V), as more efficient and stable source for
industrial applications.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
249a3cc1af arm: mxs: Provide Kconfig option to disable battery charging at IMX28 PMU
This new Kconfig option allows disabling the in-PMU battery charging
block. This may be required when DCDC_BAT source is powered not from
battery, but from already regulated, good quality source.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
1c3c601ac5 arm: mxs: Provide Kconfig option to to not use VDD5V as IMX28 PMU source
This option sets the current limit for 5V source to zero, so all
the PMU outputs are primarily powered from battery source (DCDC_BAT).

This option may be set on systems, where the 5V is NOT supposed to be
in any scenario powering the system - for example on systems where
DCDC_BAT is connected to fixed and regulated 4.2V source (so the
"battery" is not present).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Fabio Estevam
8f70f3df62 power: imx8m-power-domain: Add delay to align with kernel driver
In the imx8m power domain kernel driver, there is an extra udelay(5)
prior to requesting the domain to power up:

https://github.com/torvalds/linux/blob/v6.3/drivers/soc/imx/gpcv2.c#L347-L375

Haven't observed any issues due to the lack of this delay in U-Boot yet,
but better to align it with the kernel driver implementation.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2023-07-11 14:40:03 +02:00
Tim Harvey
79e315761c board: gateworks: venice: update board doc to show other emmc parts
Update the venice board documentation to show how to install to the
various eMMC hardware partitions available as the same binary firmware
can be placed in either user/boot0/boot1 without build-time config
changes. Note that the boot offsets differ depending on the SoC and the
eMMC hardware partition.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
13897ff6d9 board: gateworks: venice: move env location
To allow U-Boot to fit within emmc boot partitions move the env from
just under 16MiB to just under 4MiB as some emmc devices used on venice
boards have 4MiB boot partitions. This still leaves plenty of room for
U-Boot.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
7b39e5b53a board: gateworks: venice: dynamically update the update_firmware script
The update_firmware script is intended to update the boot firmware but
the details including the offset and hardware partition are dependent
on the boot device.

Specifically:
- IMX8MM/IMX8MP (BOOTROM v2) the offset is 32KiB for SD and eMMC user
  hardware partition and 0KiB for eMMC boot partitions.
- IMX8MM the offset is 33KiB for SD and eMMC regardless of hardware
  partition.

Dynamically set soc, dev, bootpart, and bootblk env vars at runtime
and use these in the update_firmware script. Remove the splblk env var
from config files as its no longer needed.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
2c2cc1eaab board: gateworks: venice: dynamically determine U-Boot env partition
Determine the U-Boot env hardware partition depending on the boot
device.

This allows the same boot firmware image to be placed on user, boot0,
or boot1 without changing CONFIG_SYS_MMC_ENV_PART.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
8236c05ddb board: gateworks: venice: dynamically determine U-Boot raw sector
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to adjust for
IMX8MN and IMX8MP when booting from an eMMC boot partition due
to IMX BOOTROM v2 using an SPL offset of 0 for boot partitions
and 32K for the user partition.

In order to allow the same firmware to run on both user and boot
hardware partitions adjust raw_sect dynamically at runtime.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
c226f84256 board: gateworks: venice: add eraseenv command
Add eraseenv command and remove the unnecessary env command.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:03 +02:00
Tim Harvey
8849cc7bd9 board: gateworks: venice: add GPIO name lookup
Add GPIO name lookup so that you can act on GPIO's by name vs controller
id:

Before:
u-boot=> gpio input pci_wdis#
GPIO: 'pci_wdis#' not found
Command 'gpio' failed: Error -22

After:
u-boot=> gpio input pci_wdis#
gpio: pin pci_wdis# (gpio 103) value is 1

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:03 +02:00
Sergio Prado
7a63432e9d configs: verdin-imx8mp: enable ARCH_MISC_INIT
This is required to boot a FIT image, otherwise the caam_jr driver is
not initialized and the hash verification fails with the following
error:

Verifying Hash Integrity ... sha256dev_get_priv: null device
CAAM was not setup properly or it is faulty

Signed-off-by: Sergio Prado <sergio.prado@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2023-07-11 14:40:03 +02:00
Oleksandr Suvorov
d31ffce81d ARM: imx9: support env in fat and ext4
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.

As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.

This solution is based on (with added SPL support):
Link: https://lore.kernel.org/all/20211020191626.3648540-1-ricardo@foundries.io/
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-07-11 14:40:02 +02:00
Giulio Benetti
04e08e3c54 arm: mx6: module_fuse: fix build failure due to wrong argument name
nodeoff variable should be variable off returned by fdt_path_offset() so
let's rename it to off.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:02 +02:00
Andrejs Cainikovs
ce38c6432b colibri-imx8x: print firmware versions
Print firmware versions during U-Boot start:

 BuildInfo:
  - SCFW f5623878, SECO-FW c9de51c0, IMX-MKIMAGE 0, ATF c6a19b1
  - U-Boot 2022.04-00335-g65192567f81-dirty

Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
2023-07-11 14:40:02 +02:00
Adam Ford
cacf0f8a19 configs: imx: imx8mm_beacon: Add config option for QSPI booting
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.

Signed-off-by: Adam Ford <aford173@gmail.com>
2023-07-11 14:40:02 +02:00
Adam Ford
5054560e0c imx: imx8mm-beacon: Enable FlexSPI in U-Boot
In order to use the FlexSPI interface in U-Boot, configure
the alias to make spi0 point to flexspi.

With that enabled, sf probe detects the QSPI part as:
SF: Detected n25q256ax1 with page size 256 Bytes, erase size 4 KiB, total 32 MiB

Signed-off-by: Adam Ford <aford173@gmail.com>
2023-07-11 14:40:02 +02:00
Tom Rini
146a82c017 Merge branch 'next' 2023-07-10 14:29:14 -04:00
Tom Rini
05aa6516c6 Prepare v2023.07
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-10 14:13:47 -04:00
Tom Rini
76c61f29d6 Merge tag 'fsl-qoriq-2023-7-6' of https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
Enable DM Serial for ls1043ardb and ls1046ardb/afrwy
Fixed secure boot on LS-CH2 platforms
2023-07-09 21:54:40 -04:00
Tom Rini
fa1e124ee7 Merge branch '2023-07-07-assorted-build-improvements' into next
- Correct a few dependencies in Kconfig and better handle some generated
  files so that they are properly cleaned later.
2023-07-08 11:28:39 -04:00
Michal Simek
99a0532a2d sysreset: Change Kconfig GPIO dependency
DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is
selected without GPIO which ends up in compilation error:
undefined reference to `dm_gpio_set_value'
undefined reference to `dm_gpio_get_value'
undefined reference to `dm_gpio_free'
undefined reference to `gpio_request_by_name'

Signed-off-by: Michal Simek <michal.simek@amd.com>
[trini: Fix configs which had relied on these select's]
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-07 16:47:15 -04:00
Ying Sun
0f42f89955 tpl: Kconfig: TPL_BANNER_PRINT depends on DEBUG_UART && TPL_SERIAL
As implemented in the arch/arm/mach-rockchip/tpl.c file,
the CONFIG_TPL_BANNER_PRINT option will not work
if either of these options is not enabled.

Add dependency constraints to the CONFIG_TPL_BANNER_PRINT option
definition to prevent configuration problems
where option is enabled but do not take effect.

Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
2023-07-07 16:25:56 -04:00
Ying Sun
29f925d8f9 common: Kconfig: SYS_CONSOLE_ENV_OVERWRITE depends on SYS_CONSOLE_IS_IN_ENV
CONFIG_SYS_CONSOLE_ENV_OVERWRITE is implemented in common/console.c
when "#if CONFIG_IS_ENABLED(SYS_CONSOLE_IS_IN_ENV)" is met.

It is recommended to add dependency constraints to its definition.

Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
2023-07-07 16:25:56 -04:00
Ying Sun
aadc1a6069 cmd: CONFIG_CMD_SAVES depends on CONFIG_CMD_LOADS
CONFIG_CMD_SAVES is used to enable support for the "saveenv" command
and is only implemented in cmd/load.c
when "#if defined(CONFIG_CMD_LOADS)" is met.

It is recommended to add dependency constraints to its definition.
Prevents "saveenv" command from not being supported
when "CONFIG_CMD_SAVES=y CONFIG_CMD_LOADS=n".

Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
42c0e5bb05 test: Find leftovers after clean/mrproper
Docs describe 'make clean' to delete most generated files, 'make
mrproper' to delete current configuration and all generated files. This
test tries to assert it.

Idea is to search remaining files by patterns in copies of the initial
out-of-source build, which has two advantages:
- looking in an out-of-source build dir allows to tell generated source
  code from committed source code
- copying is fast (compared to rebuilding each time) which allows to do
  a "world clean"

Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
57fdec65c5 Kbuild: Fix cleanup of *.dtbo for sandbox
sandbox can generate DT overlays, but they were not cleaned.

Extend the explicit clean-files list accordingly.

Fixes: 95300f203f ("pytest: add sandbox test for "extension" command")
Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
3d3eeae9bf Kbuild: Fix cleanup of *.dtb for some archs
'make clean' did not descend into arch/$ARCH/dts for arc, m68k, nios2,
sh, xtensa.

Fix it by adding the missing archs to the explicit clean-dirs list.

Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
45e636f41f Kbuild: Fix cleanup of VPL
VPL artifacts like example vpl/u-boot-vpl are currently not removed by
'make clean'.

We can clean them just as it's already done for SPL and TPL.

Fixes: f86ca5ad8f ("Introduce Verifying Program Loader (VPL)")
Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
c623642d29 Adjust gitignore for tools/generated/
Tell git that auto-generated C sources are now exclusively expected
under tools/generated/.

Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
2023-07-07 16:25:56 -04:00
Tobias Deiminger
60a8cf5db8 Kbuild: Fix cleanup of generated sources in tools
On 'make clean', generated C files in tools/env/ and tools/boot/ are
currently not removed, but they should.

Auto-generation for shared sources was first introduced with
ad80c4a322 ("kbuild, tools: generate wrapper C sources automatically
by Makefile"). Cleanup later regressed (see Fixes:), because shared
files were moved out of lib/ and common/, but 'clean-dirs := lib common'
was not adjusted accordingly. Further, the generated
tools/env/embedded.c became a sibling to project files, which prevents
directory-wise cleanup at all.

To solve it, we establishe tools/generated/ as the sole place for
generated sources. Wrappers are now generated as
tools/generated/<orig_dirname>/<orig_filename>, and 'make clean' can
remove tools/generated/ as a whole (Linux Makefile.asm-generic headers
are cleaned similarly). This way we don't have to maintain separate
clean-files or clean-dirs entries for each single added or moved wrapper
file.

Fixes: 0649cd0d49 ("Move environment files from common/ to env/")
Fixes: 19a91f2464 ("Create a new boot/ directory")
Signed-off-by: Tobias Deiminger <tdmg@linutronix.de>
[trini: Correct mkfwupdate case]
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-07 16:25:39 -04:00
Eugen Hristev
0beb649053 MAINTAINERS: correct at91 tree link
This was not done when the tree name was changed, fix it now.

Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
2023-07-07 11:37:09 -04:00
Tom Rini
56c7fac8ad Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-usb into next 2023-07-06 13:23:36 -04:00
Tom Rini
6fc3107559 Merge branch 'riscv-for-next' of https://source.denx.de/u-boot/custodians/u-boot-riscv into next
- RISC-V CI OpenSBI version update
- Andes ae350 board modification
- Sync PolarFire SoC dts with Linux
- Support building ubifs
2023-07-06 13:21:37 -04:00
Yu Chien Peter Lin
12f66e2197 board: ae350: Add missing env variables for booti
The 'booti' command is unable to boot Image.gz due to the absence
of required environment variables 'kernel_comp_addr_r' and
'kernel_comp_size'.

This commit adds these variables and reorganizes the memory layout
to prevent any overlap between binaries and files.

Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-07-06 17:28:08 +08:00
Yu Chien Peter Lin
bc35b49a5c riscv: andes_plicsw: Fix IPI during OpenSBI invocation
On some AE350 boards, we need to explicitly initialize the priority
registers to a non-zero value so the boot hart can instruct secondary
harts to jump to OpenSBI.

This patch also updates the information about PLICSW.

Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-07-06 17:28:08 +08:00
Heinrich Schuchardt
9eb0fc24c9 RISC-V: CONFIG_SPL_OPENSBI_SCRATCH_OPTIONS description
Describe which numeric values can be used for as scratch options for
OpenSBI.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
2023-07-06 17:28:08 +08:00
Hoegeun Kwon
422fc299df clk: starfive: pll: Fix to use postdiv1_mask
There is a problem that the rates of PLL0 and PLL1 are set incorrectly
because the postdiv1_mask value is incorrectly entered when setting
the pll clk reg. Modify postdiv1's mask value to be put correctly.

Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2023-07-06 17:28:08 +08:00
Bin Meng
0a8239afa3 ci: riscv: Update OpenSBI to v1.2
Use the latest OpenSBI v1.2 release binaries for the RISC-V CI.

Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-07-06 17:28:08 +08:00
Conor Dooley
e530bb743b board: microchip: set mac address for ethernet1 on icicle
The dts sync from Linux leaves mac0/ethernet1 enabled on icicle, but
U-Boot does not currently set a mac address for it. Expand on the code
which currently sets the mac for mac1/ethernet0 to optionally set the
mac address for the second ethernet.

Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
2023-07-06 17:28:08 +08:00
Conor Dooley
4e99899bd5 riscv: dts: sync mpfs-icicle devicetree with linux
The "notable" disappearances are:
- the pac193x stanza - there's nothing in mainline linux w.r.t. bindings
  for this & what is going to appear in mainline linux is going to be
  incompatible with what is currently in U-Boot.
- operating points - these operating points should not be set at the
  soc.dtsi level as they may not be possible depending on the design
  programmed to the FPGA
- clock output names - there are defines for the clock indices, these
  should not be needed
- the dt maintainers in linux NAKed using defines for IRQ numbers
- the qspi nand, which is not part of the icicle's default configuration
  is removed.

Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2023-07-06 17:28:08 +08:00