This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
This patch adds "zu39dr" to the list of zynqmp devices
The zu39DR is the new RFSoC silicon with id value of 0x66.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch checks for zynq aes & rsa commands max parameters count. Also
checks minimum number of parameters count for aes command.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed the return type of reset_reason() to int from u32, because
zynqmp_mmio_read/write() returns signed value on error.
Replaced readl and writel functions with zynqmp_mmio_read &
zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
For example:
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For testing purpose use zcu102 which has SD at controller 1 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00279-gdc482e7ee092 (Nov 30 2018 - 10:22:56 +0100)
Model: ZynqMP MINI EMMC1
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff170000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100)
Model: ZynqMP MINI EMMC0
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff160000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If only usb ethernet gadget is enabled it can start automatically.
If more gagdets are enabled usb ethernet gadget can be bind by
"bind /amba/usb1@ff9e0000/dwc3@fe300000 usb_ether" (on zcu100)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Wire up mini_qspi SPL with zcu102 for testing purpose.
Normally mini u-boot runs with FSBL/SPL for certain board.
Enabling SPL and configuration from zcu102 helps with testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If SYS_LONGHELP is disabled the following warning is generated:
board/xilinx/zynq/cmds.c:496:13: warning: ‘zynq_help_text’ defined but
not used [-Wunused-variable]
Normal way for fixing this is to guard the whole variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The VCU disable bit(8) in IP disable register of efuse
is valid only if PL powered up and hence PL powerup status
has to be considered while determining the CG part also.
This patch considers the PL powerup status and ignores the VCU
disable bit if PL not powered up.
This fixes the issue of "unknown" id for CG parts if PL not powered up
and VCU bit(8) is not set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This issue is reported by kconfiglib:
warning: style: quotes recommended around default value for string
symbol XILINX_MICROBLAZE0_HW_VER (defined at
board/xilinx/microblaze-generic/Kconfig:37)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch added support of mmio read and write commands. These commands
can be used to read and write registers from the u-boot command line.
It can be useful in debugging.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should support watchdog reset so that WATCHDOG_RESET will function
properly.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed zynqmp command to handle subcommands with
U_BOOT_CMD_MKENT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change as was done for zynqmp with this description:
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0= &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
<zynqmp example removed>
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0 = &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
dm tree fragment for above configuration with patch applied:
ZynqMP> dm tree
Class index Probed Driver Name
-----------------------------------------
...
watchdog 0 [ ] cdns_wdt | |-- watchdog@ff150000
watchdog 1 [ + ] cdns_wdt | `-- watchdog@fd4d0000
...
dm uclass fragment:
ZynqMP> dm uclass
...
uclass 75: watchdog
0 watchdog@ff150000 @ 7df02f40, seq -1, (req 1)
1 * watchdog@fd4d0000 @ 7df02ff0, seq 0, (req 0)
...
It is visible that index 1 is IP with seq 0 which means that FPD
watchdog (@fd4d0000) is in DT below LPD watchdog (@ff150000).
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sysreset uclass have own do_reset function which should be used instead
of board/platform specific.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
calloc() can fail and return NULL. The patch is checking return value
and return in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Detect mmc alias at run time for setting up proper boot_targets sequence.
The first target has to correspond with boot mode.
The purpose of this patch is to get rid of CONFIG_ZYNQ_SDHCI0/1
parameters in full U-Boot.
Unfortunately this patch can't remove it because there is missing
mmc implementation for SPL_DM_SEQ_ALIAS.
Also xilinx_zynqmp.h only setup boot commands for mmc0 and mmc1.
It means using aliases with higher number won't work. But switching
between mmc0 and mmc1 should work properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Read reset reason reg and show it in log and also save it as variable.
Clearing reset reason when it is read to show only one status
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
