The CAAM output ring size register offset is currently defined in fsl_sec.h
as FSL_CAAM_ORSR_JRa_OFFSET, use this definition to avoid hardcoded value in
i.MX common code.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ B2 is using same value in OCOTP_READ_FUSE_DATA like B1, so
we have to check the ROM verision to distinguish the revision.
As we have checked the B1 rev for sticky bits work around in
secure boot. So it won't apply on B2.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The value of Unique ID in uboot and kernel is different for iMX8MP:
serial#=02e1444a0002aaff
root@imx8mpevk:/sys/devices/soc0# cat soc_uid
D699300002E1444A
The reason is that Fuse Addresses of Unique ID of iMX8MP are 0x420 and
0x430.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual core and single core iMX8M parts, the thermal node and PMU node
in kernel DTB also needs update to remove the refers to deleted core nodes.
Otherwise both driver will fail to work.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are 3 part numbers for 11x11 i.MX8MNano with different core number
configuration: UltraLite Quad/Dual/Solo
Comparing with i.MX8MN Lite parts, they have MIPI DSI disabled. So
checking the MIPI DSI disable fuse to recognize these parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device
HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.
This will make HS400 mode work reliably on the LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.
Signed-off-by: Michael Walle <michael@walle.cc>
The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The ethernet memory power domain is handled by the meson-ee-pwrc driver,
delete the static code.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Trusted Firmware now adds the /reserved-memory subnode to the DT at
runtime[1], putting in the right values.
Drop our hard-coded version, as this might clash with the actual values
(which have also changed), and rely on TF-A to add the node.
[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.
The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).
Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the following device tree properties for nand flash
- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.
With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.
Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prevent running out of memory, increase SYS_MALLOC_F_LEN to 0x4000
similar to what rk3399 uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On RISC-V the symbols __dyn_sym_start, dyn_sym_end are referenced in
efi_runtime_relocate().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:
- two pins provided in a ternary arrangement, for 9 combinations.
- reading from the EC
Add a binding doc and drop the unused #defines as well.
Example:
U-Boot 2021.01-rc5
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
DRAM: 3.9 GiB
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
Video: 1024x768x32 @ b0000000
Model: Google Coral (memconfig 5, SKU 3)
This depends on the GPIO series:
http://patchwork.ozlabs.org/project/uboot/list/?series=228126
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
It is not possible to remove the state before driver model is uninited,
since the devices are allocated in the memory buffer. Also it is not
possible to uninit driver model afterwards, since the RAM has been
freed.
Drop the uninit altogether, since it is not actually necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.
Tidy up the TODO that prompted this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox removes its executable after failing to run it,
since there is no other way that it would get cleaned up.
However, this is actually only wanted if the image was created within
sandbox. For the case where the image was generated by the build system,
such as u-boot-spl, we don't want to delete it.
Handle the two code paths accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting from coreboot there is no need to notify the FSP of anything,
since coreboot has already done it. Nor it is possible, since the FSP
details are not provided by coreboot.
Skip it in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting from coreboot the FSP video information is no-longer
available. Enable the coreboot driver so that we can get some sort of
display in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the debug UART is only set up in SPL, on the assumption that
the boot flow will always pass through there. When booting from coreboot,
SPL is not used, so the debug UART is not available.
Move the code into a common place so that it can be used in U-Boot proper
also. Add the required init to start_from_spl.S as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver cannot work when booted from coreboot, since the FSP
information is not available. Disable it in that case, so that the
coreboot video driver can be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code into a generic location so that it can be used by other x86
boards which want to boot from coreboot. Also ensure that this is called
if booting from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
