After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.
This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.
We could maybe in the future map U-boot environment variables to EFI variables
here.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Boards using the TWL6030 regulator may not all use the LDOs the same way.
Some might also not use MMC1 at all, so VMMC would't have to be enabled.
This delegates TWL6030 MMC power initializations to board-specific functions,
that may still call twl6030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.
Also update the mux for SD card detect on DRA74-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating the memory banks properly so that DT is populated accordingly.
And updating this only after DDR is properly detected by eeprom, so that
git bisect is still maintained.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The REVH and later versions of DRA7-evm uses MICRON MT41K512M16HA-125 memory
chips which is of size 4GB(2GB on EMIF1 and 2GB on EMIF2). Add support for the
same.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA7 EVM revH and later EVMs have EEPROM populated that can contain board
description information such as name, revision, DDR definition, etc. Adding
support for this EEPROM format.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are certain EMIF timing failures seen on the some x15 boards. Updating
the EMIF settings to get rid of these timing failures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.
Tested on the Logic PD Torpedo + Wireless.
I only changed a handful of devices that used the same syntax as the Logic
board. Appologies if I missed one or stepped on toes. Thanks to Derald Woods
and Alexander Graf.
Signed-off-by: Adam Ford <aford173@gmail.com>
V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c
V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c
V4: Fix subject heading
V3: Remove reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.
V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Because KS2 u-boot works in 32 bit address space the existing ram_size
global data field cannot be used. The maximum, which the get_ram_size()
can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size
to fix up dtb.
This commit introduces the ddr3_get_size() which uses SPD data to
calculate the ddr3 size. This function replaces the "ddr3_size"
environment variable, which was used to get the SODIMM size.
For platforms, which don't have SODIMM with SPD and ddr3 is populated to
a board a simple ddr3_get_size function that returns ddr3 size has to be
implemented. See hardware-k2l.h
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.
The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The maximum device and arm speeds can be determined by reading
EFUSE_BOOTROM register. As there is already a framework for reading this
register, adding support for all possible speeds on k2g devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Its not compulsory that speed definition should be same on EFUSE_BOOTROM
register for all keystone 2 devices. So, allow for board specific
speed definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).
The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.
Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.
NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.
This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a generic TI eeprom logic which can be reused across
platforms, reuse the same.
This revision also includes fixes identified by Dave Gerlach
<d-gerlach@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the generic EEPROM detection logic instead of duplicating the AM
eeprom logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Several TI EVMs have EEPROM that can contain board description information
such as revision, DDR definition, serial number, etc. In just about all
cases, these EEPROM are on the I2C bus and provides us the opportunity
to centralize the generic operations involved.
The on-board EEPROM on the BeagleBone Black, BeagleBone, AM335x EVM,
AM43x GP EVM, AM57xx-evm, BeagleBoard-X15 share the same format.
However, DRA-7* EVMs, OMAP4SDP use a modified format.
We hence introduce logic which is generic between these platforms
without enforcing any specific format. This allows the boards to use the
relevant format for operations that they might choose.
This module will compile for all TI SoC based boards when
CONFIG_TI_I2C_BOARD_DETECT is enabled to have optimal build times for
platforms that require this support.
It is important to note that this logic is fundamental to the board
configuration process such as DDR configuration which is needed in
SPL, hence cannot be part of the standard u-boot driver model (which
is available later in the process). Hence, to aid efficiency, the
eeprom contents are copied over to SRAM scratchpad memory area at the
first invocation to retrieve data.
To prevent churn with cases such as DRA7, where eeprom format maybe
incompatible, we introduce a generic common format in eeprom which
is made available over accessor functions for usage.
Special handling for BBG1 EEPROM had to be introduced thanks to the
weird eeprom rev contents used.
The follow on patches introduce the use of this library for AM335x,
AM437x, and AM57xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
remove board_eth_init when CONFIG_DM_ETH is defined
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
In Mainline Kernel as of:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6
Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1
Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
A few config files have been added without updating MAINTAINERS.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently omap_hsmmc driver doesn't use sdcd pin to detect
whether the card is present or not. Instead the same pin is used
as GPIO to detect card presence. So change the pin mux mode from
mmc0_sdcd to gpio0_6.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC support for k2g
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Add Ethernet support for tftp support
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add clock information for Galileo
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Prepare board file so that ethernet registration are
commented for DM conversion
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_name environment variable was not getting set correctly for Pandaboard A4 and ES
Signed-off-by: David Batzle <dbatzle@dcbcyber.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>; Tom Rini <trini@ti.com>; Peter Robinson <pbrobinson@gmail.com>
On keystone2 Lamarr and Edison platforms, the PA clocksource
mux in PLL REG1, can be changed only after enabling its clock
domain.
So selecting the output of PASS PLL as input to PA only after
enabling the clockdomain.
This is as per the debug done by "Vitaly Andrianov <vitalya@ti.com>"
and based on the previous work done by "Hao Zhang <hzhang@ti.com>"
Fixes: d634a0775bcf ("ARM: keystone2: Cleanup PLL init code")
Reported-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested on my TI186x rev E. (PG2.0) and take over maintainership.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Take over maintainership as well. Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).
Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
