A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When Trimslice is booted from serial flash, the boot ROM does this, so
U-Boot doesn't need to. However, booting from the SD slot for recovery
purposes, the boot ROM does not set up the pinmux for serial flash. Add
code to U-Boot to set this up, so that an SD-based recovery U-Boot image
can upgrade the U-Boot in serial flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards can override this to set up the pinmux correctly to access serial
flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Instead of initializing USB as soon as bootcmd is executed, defer it
until the first boot device that (potentially in the case of network)
uses USB is scanned. This avoids initializing USB when booting from MMC,
so speeds that up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Place the list of searched boot devices, file-system types, boot file
locations/prefixes, and boot script names into variables. This allows
the user to override them directly (e.g. to change boot order, or select
the specific values they use) without having to edit the main bootcmd
and script_boot variables.
The default boot order is changed from USB, MMC, DHCP to MMC, USB, DHCP.
This speeds up the typical MMC boot case. People who want USB boot can
now edit variable boot_targets appropriately.
Also, reformat BOOTCMDS_COMMON to fit within 80 columns.
Potential future enhancements might be:
* Allow boards to specify which of bootcmd_mmc0/... should be defined,
based on the HW they contain.
* Allow boards to influence the order that the boot targets are added
into the boot_targets variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's boot ROM supports a mode whereby code may be downloaded and flash
programmed over a USB connection. On dev boards, this is typically entered
by holding down a "force recovery" button and resetting the CPU. However,
not all boards have such a button (one example is the Compulab Trimslice),
so a method to enter RCM from software is useful.
This change implements the command "enterrcm" to do this, and enables it
for all Tegra boards by default. Even on boards other than Trimslice,
controlling this over a UART may be useful, e.g. to allow simple remote
control without the need for mechanical button actuators, or hooking up
relays/... to the button.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
So that all Tegra boards define environment variables that describe
themselves.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This can be useful for generic scripts. For example, rather than hard-
coding a script to ext2load tegra-harmony.dtb, it could load
${soc}-${board}.dtb and hence not need adjustments to run on multiple
boards.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
loop_count runs down from 10000, so the correct condition to error out
is ==0.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren.nvidia@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
GPIO PI6 can be used to obtain the write-protect status of an SD card
inserted into the SD slot.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commit fa042186b9.
It causes build warnings like this:
cpu.c:48:1: warning: -fstack-usage not supported for this target
[enabled by default]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 896bbb5 "fdt: avoid bad MAKEALL status" added logic to capture
the result code from dtc by echoing $? to stdout and capturing it using
$(). However, dtc emits some diagnostics to stderr and some to stdout.
The diagnostics send to stdout ended up getting captured via $() rather
than being echo'd to the user. This caused those diagnostics to be passed
to the exit command, which would then fail with the following cryptic
error message:
/bin/sh: line 1: exit: too many arguments
Solve this by redirecting all dtc output to stderr so that $() does not
capture it. This allows the user to see the actual error message from dtc.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: albert.u.boot@aribaud.net
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This warning was introduced in 436da3c "ext2load: increase read
speed":
ext2fs.c: In function 'ext2fs_read_file':
ext2fs.c:458:19: warning: 'blocknxt' may be used uninitialized in this function [-Wuninitialized]
this change makes it go away.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mkenvimage does not build due to missed os_support.o and unsupported
file modes S_IRGRP S_IWGRP.
Tested with mingw 4.2.1 on ubuntu 12.04.
Signed-off-by: Vladimir Yakovlev <nagos@inbox.ru>
commit "net: use common rand()/srand() functions" introduced the following
build warning on the current u-boot-arm tree:
$ ./MAKEALL MPC8313ERDB_66
Configuring for MPC8313ERDB_66 - Board: MPC8313ERDB, Options: SYS_66MHZ
text data bss dec hex filename
271988 13976 41768 327732 50034 ./u-boot
In file included from bootp.c:15:0:
net_rand.h: In function 'srand_mac':
net_rand.h:40:2: warning: implicit declaration of function 'srand' [-Wimplicit-function-declaration]
adding this dependency fixes it.
Cc: Michael Walle <michael@walle.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Michael Walle <michael@walle.cc>
Drop mdelay() macros since we already have a common mdelay() func.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
The following is the cleanup sequence in arch/arm/cpu/armv7/cpu.c
int cleanup_before_linux(void)
{
...
...
dcache_disable();
v7_outer_cache_disable();
invalidate_dcache_all();
}
1) invalidate_dcache_all call expects that all the caches has been
flushed, invalidated and there are no dirty entries prior to its
execution. In the above sequence dcache_disable() flushes, invalidates
the caches and turns off the mmu. But after it cleanups the cache
and before the mmu is disabled there is a cp_delay() function which
has STR instruction. On certain cores like the cortex-a15, cache hit
and a write can happen to a cache line even when the dcache is
disabled. So the above mentioned STR instruction creates a dirty entry
after cleaning. The mmu gets disabled after this.
2) invalidate_dcache_all invalidates the cache lines. Again on
cores like cortex-a15, invalidate instruction flushes the dirty
line as well. So some times the dirty line from sequence 1
can corrupt the memory resulting in a crash.
Fixing this by moving the get_cr() and cp_delay() calls before
cleaning up the cache, thus avoiding the dirty entry.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Introduce arch_early_init_r() function, which can be useful for doing
early initialization after relocation has happened.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
No need to define CONFIG_ARCH_CPU_INIT.
All mx28 based boards should use arch_cpu_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Needed for redundant environment for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
i2c_probe() is changed to reinit the i2c bus upon read failure.
This is naturally the case upon i2c bus probing.
Also, some printf messages upon read failure are removed. As they
would interfere with the "i2c probe" command.
Additionally, i2c_set_bus_speed() now returns 0, so that the
"i2c speed" command can be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Add support for the M41T82 RTC to the m41t62 driver. The only
difference that needs to be handled by this driver, is to
clear the HT (Halt Update) bit upon reset. This bit is not
used on the M41T62, so its save to clear this bit always.
The M41T82 support will be used by the X600 (SPEAr600)
board support.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
On x600 (SPEAr600) U-Boot is appended to U-Boot SPL. Both images are
created using mkimage (crc etc), so that the ROM bootloader can check
its integrity. Padding needs to be done to the SPL image (with
mkimage header) and not the binary. Otherwise the resulting image
which is loaded/copied by the ROM bootloader to SRAM doesn't fit.
The resulting image containing both U-Boot images is called u-boot.spr.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).
Signed-off-by: Stefan Roese <sr@denx.de>
This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).
Signed-off-by: Stefan Roese <sr@denx.de>
raise() likes to call printf() if it is available, but in SPL builds it
either is not available, or adds a large chunk to the resulting image
size.
So don't call it even if it is available.
This change reduces SPL size from 10KB to 6.3KB on hawkboard, for
example, using generic relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
In SPEAr, some of the configuration flags eg. CONFIG_SPEAR_EMI, were given value
"1", which isn't required. Define the flags without assigning any value
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When CONFIG_MTD_NAND_VERIFY_WRITE is defined, nand driver read back the data
everytime it writes. This process unnecessarily slows down the nand access.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
