Make the indent of these macro elements consistent with the
rest of this table. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for debug output very early during boot using the DEBUG_UART
mechanism. This uses a static fixed UART port configuration selected via
Kconfig options and dedicated print functions from debug_uart.h. This is
useful e.g. when debugging problems so early during boot, that not even
the DM is initialized at that point, and thus DM_SERIAL is not available
either.
This functionality is disabled by default. To activate it, define the
following Kconfig options and select SCIF type using CFG_SCI/CFG_SCIF_A/
CFG_HSCIF/<nothing for regular SCIF>:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_SCIF=y
CONFIG_DEBUG_UART_BASE=0xe6540000
CONFIG_DEBUG_UART_CLOCK=24000000
The later two options define the SCIF physical base address and SCIF
input clock in Hz. Optionally, to validate DEBUG_UART works, enable
the following as well to get early serial output message by default:
CONFIG_DEBUG_UART_ANNOUNCE=y
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Both CONFIG_SCI and CONFIG_SCIF_USE_EXT_CLK options do not have a
matching Kconfig entry because they are internal to the SCIF driver.
Change their prefix to CFG_, i.e. CFG_SCIF_USE_EXT_CLK and CFG_SCI,
to reflect that and avoid interferring with Kconfig symbols. Since
neither of those options are defined elsewhere, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Switch ifdef in sh_gpio_get_value() to IS_ENABLED() macro.
The CONFIG_RCAR_GEN3 will never have SPL counterpart, so
the IS_ENABLED() macro is the right one here. No functional
change, except for improved build test coverage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Calling old U-Boot API doesn't allow to use fixed PHY.
Searching by mask is the part of new function, after
scanning FDT for a fixed PHY definition
Fixes: e821a7bdb1 ("net: ravb: Detect PHY correctly")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Mikhail Lappo <mikhail.lappo@esrlabs.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Hai Pham: Drop phy_connect_dev since it's called in phy_connect]
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use mask -1 instead of 0 to reinstate the search behavior
over all PHY addresses. Add Fixes tag, sort the tag list.]
Sort the list of "depends" symbols in ascending order.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Sort the list of "depends" symbols in ascending order.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Do not cache the single CPG MODE register bit 12, instead cache the
entire register value, and only pick the matching bit from the cached
value when core clock of type MDSEL or PE are used. Both MDSEL and PE
clock type currently define .offset field as 12 on Gen3, which means
this code will use bit 12 on Gen3 again, however there are additional
clock on Gen4 which use different bits, and having this flexibility
in place now will be useful when adding Gen4.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This reverts commit 9f62a472df.
The changes here aren't quite right, and on platforms such as Raspberry
Pi where we can have both serial and video output, the change above
causes output to change. This can be seen as the hush tests we have now
fail.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is better to clear the console device rather than the video device,
since the console has the text display. We also need to reset the cursor
position with the console, but not with the video device.
Add a new function to handle this and update the 'cls' command to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible for the video driver to use a pre-allocated
frame buffer (such as is done with EFI) with the copy framebuffer. This
can be useful to speed up the display.
Adjust the implementation so that copy_size can be set to the required
size, with this being allocated if the normal framebuffer size is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for this to EFI in case it becomes useful. At present it just
slows things down. You can enable CONFIG_VIDEO_COPY to turn it on.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is not yet clear how to read the timer via EFI. The current value seems
much too high on a Framework laptop I tried. Adjust it to a lower
hard-coded value for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current vesa structure only provides a 32-bit value for the frame
buffer. Many modern machines use an address outside the range.
It is still useful to have this common struct, but add a separate
frame-buffer address as well.
Add a comment for vesa_setup_video_priv() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put this into a function, as we have done for the app implementation.
Comment both functions. FOr now the app still does not access it
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Correct the board code ID based on the hardware documentation
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove PFC info table entries which are never instantiated,
since there are no drivers for those. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.
This failure occurs specifically in case SDnCKCR reads back 0x209 .
Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.
Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes: 5454dea313 ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Ofnode value is not set, so all the DT properties are not being read
and due to this default values are being used.
Find nand node and set chip->flash_node value.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Bad block table option is hardcoded to read from flash with
NAND_BBT_USE_FLASH option. This decision should be done based on DT
property. Remove this hardcoding, to be able to use DT property.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It was incorrectly using an old priv->regs pointer, which was
initialized to zero. SPI resets won't happen on first call.
Signed-off-by: Jiajie Chen <c@jia.je>
Link: https://lore.kernel.org/r/20230227150938.211820-1-c@jia.je
Signed-off-by: Michal Simek <michal.simek@amd.com>
When using the fpga loads command, the driver is passing the AES encryption
key address is all cases. However, for the authenticated, but not encrypted
use case, there is no AES encryption key, and this value is 0.
When AES encryption is not used on the fpga bitstream, the pmufw assumes that
the AES key address is a bitstream size value like what is used by the
unsecure fpga load command.
To fix the problem, this patch checks to see if the AES key address is zero.
If the AES key address is zero, it means that AES is not being used on the
bitstream and the bitstream size should be passed instead. Thus, matching
the fpga load functionality.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230214131959.40298-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5f ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZAdiLw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDtGAJ9ZjsnfneJpUjwYJWOw2ibnm9Dh2QCfVCAy+Bxa
YfqV8y7TbOuCQKTEY1s=
=FJhw
-----END PGP SIGNATURE-----
Merge tag 'next-20230307' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- video console refactoring and optimization
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow font size configuration at runtime for console_simple.c
driver. This needed for unit testing different fonts.
Configuring is done by `font` command, also used for font
selection in true type console.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since multiple vidconsole drivers exists, vidconsole_get_font_size()
implementation cannot longer live in vidconsole_uclass.c file.
Move current vidconsole_get_font_size logic to truetype driver ops.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This needed for unit testing different fonts.
Configured fonts are placed in an array of fonts.
First font is selected by default upon console probe.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agust: fixed build error when bmp logo disabled]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Devices with high ppi may benefit from wider fonts.
Current width implementation is limited by 1 byte, i.e. 8 bits.
New version iterates VIDEO_FONT_BYTE_WIDTH times, to process all
width bytes, thus allowing fonts wider than 1 byte.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- move common code to vidconsole_internal.h and console_core.c
- unite probe functions
- get rid of code duplications in switch across bpp values
- extract common pixel fill logic in two functions one per
horizontal and vertical filling
- rearrange statements in put_xy* methods in unified way
- replace types - uint*_t to u*
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the file spear_sdhci.c file is already removed, delete the associated
configuration CONFIG_MMC_SDHCI_SPEAR.
Fixes: c942fc925e ("mmc: spear: remove the entire spear_sdhci.c file")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
The fttmr010 timer driver was deleted by
commit 29fc6f2492 ("ARM: remove a320evb board support")
The original source file was: arch/arm/cpu/arm920t/a320/timer.c
Return the driver to the codebase in a DM compatible form.
A platform using fttmr010 will be submitted later.
This hardware is described in the datasheet [1], starting from page 348.
According to the datasheet, there is a Revision Register at offset 0x3C,
which is not present in 'struct fttmr010'. Add it and debug() print
revision in probe function.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
- Partial merge of a series of mine to select some framework options
that shouldn't be prompted for (and remove some unused code related to
that), and a partial merge of a series from Simon to remove some dead
code and address various CONFIG_IS_ENABLED/IS_ENABLED issues in code.
Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At present we enable the sandbox I2C driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present we enable the sandbox RTC driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
