Commit graph

10 commits

Author SHA1 Message Date
Stefano Babic
81687212ee I2C: mxc_i2c: address failure with mx35 processor
There is sporadic failures when more as one I2C slave
is on the bus and the processor tries to communicate
with more as one slave.
The problem was seen on a mx35pdk (two I2C slaves,
PMIC controller and CAN/RTC chip).

The current driver uses the IIF bit in the status register
to check if the bus is busy or not. According to the manual,
this is not correct, because the IIB bit should be checked.
Not only, to check if a transfer is finished must be checked
the ICF bit, and this is not tested at all.

This patch comes from analyse with a corresponding driver
provided by Freescale as part of the LTIB tool. Comparing
the two drivers, it appears that the current u-boot driver checks
the wrong bits, and depending on race condition, the transfer
can be successful or not.

The patch gets rid also of own debug function (DPRINTF),
replaced with the general debug().

Tested on Freescale mx35pdk.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:43 +01:00
Stefano Babic
1d549ade61 I2C: mxc_i2c: get rid of __REG access
This driver accesses to processor's register
via __REG macros, that are removed (or are planned
to be removed) and replaced by C structures.
This patches replaces all occurrencies of __REG macros.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:42 +01:00
Stefano Babic
04220612f6 mxc_i2c: Add support for the i.MX35 processor
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:42 +01:00
Liu Hui-R64343
127cec1889 mxc_i2c: add support for MX53 processor
This patch add I2C support for Freescale MX53 processor

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:42 +01:00
Guennadi Liakhovetski
e7de18afe8 i.MX31: Start the I2C clock on driver initialisation
i.MX31 powers on with most clocks running, so, after a power on this explicit
clock start up is not required. However, as Linux boots it disables most clocks
to save power. This includes the I2C clock. If we then soft reboot from Linux
the I2C clock stays off. This breaks the phycore, which has its environment in
I2C EEPROM. Fix the problem by explicitly starting the clock in I2C driver
initialisation routine.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Ack-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-14 10:00:51 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Michal Simek
a4a549b4b5 i2c: Clean drivers/i2c/ Makefile
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-08-18 23:24:01 +02:00
Sascha Hauer
cdace06612 add an i2c driver for mx31
This patch adds an i2c driver for Freescale i.MX processors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-13 14:21:43 -07:00
Wolfgang Denk
950a392464 Revert merge of git://www.denx.de/git/u-boot-arm, commit 62479b18:
Reverting became necessary after it turned out that the patches in
the u-boot-arm repo were modified, and in some cases corrupted.

This reverts the following commits:

	066bebd635
	7a837b7310
	c88ae20580
	a147e56f03
	d6674e0e2a
	8c8463cce4
	c98b47ad24
	8bf69d8178
	8c16cb0d3b
	a574a73852
	1377b5583a
	1704dc2091

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-11 15:11:26 +02:00
Sascha Hauer
8c8463cce4 add an i2c driver for mx31
This patch adds an i2c driver for Freescale i.MX processors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30 11:32:16 +01:00