Basically the same as on sam9x60-ek. Same as in Linux. NAND flash is
correctly detected when booting into U-Boot:
U-Boot 2023.07-rc6-00005-g12719f75dc-dirty (Jul 05 2023 - 13:06:35 +0000)
CPU: SAM9X60 128MiB DDR2 SiP
Crystal frequency: 24 MHz
CPU clock : 600 MHz
Master clock : 200 MHz
Model: Microchip SAM9X60 Curiosity
DRAM: 128 MiB
Core: 145 devices, 22 uclasses, devicetree: separate
NAND: 512 MiB
MMC: sdhci-host@80000000: 0, sdhci-host@90000000: 1
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@f802c000
Hit any key to stop autoboot: 0
Signed-off-by: Alexander Dahl <ada@thorsis.com>
- nodes moved
- using node references by label instead of dulicating the node tree
Makes it easier to compare with the dts file from Linux kernel.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The user guide says it's a Microchip 24AA025E48 serial EEPROM, which is
a 2-Kbit I2C Serial EEPROM with EUI-48™ Identity. This is the chip
actually populated on board EV40E67A rev 4.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
No functional changes, but this:
- reorder nodes (ordered by memory offset as in Linux)
- add label to pinctrl node name for easier reference in board files
- fix whitespace
Diff to sam9x60.dtsi in Linux is much better readable now.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
- Add a little more info to 'cbsysinfo' command
-----BEGIN PGP SIGNATURE-----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=s8Ab
-----END PGP SIGNATURE-----
Merge tag 'x86-pull-20230801' of https://source.denx.de/u-boot/custodians/u-boot-x86
- MTRR fixes for x86 boards
- Add a little more info to 'cbsysinfo' command
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZMj+xA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPovAJ9DU0H3Xm9LmrPZE4NzmmkfKJ/99QCfTlDfIkZI
dVilMWOHsRX1SgMS6YM=
=KYKc
-----END PGP SIGNATURE-----
Merge tag 'video-20230801' of https://source.denx.de/u-boot/custodians/u-boot-video
- dm video cosmetic style fix
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
Perform removal of DSS if kconfigs VIDEO_REMOVE or SPL_VIDEO_REMOVE is
set by user. Otherwise if above Kconfigs are not selected, it is assumed
that user wants splash screen to be displayed until linux kernel boots
up. In such scenario, leave the power domain of DSS as "on" so that
splash screen stays intact until kernel boots up.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Change remove method of DSS video driver to disable video port instead
of performing a soft reset, as soft reset takes longer duration. Video
port is disabled by setting enable bit of video port to 0.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
At present the uclass stored frame buffer size is set to a hard
coded value, but we can calculate the correct value based on what
is configured.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Set up a default frame buffer size of 8MiB for Bochs for non-x86
architecturs as PCI is normally not enumerated before relocation
on these architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI is always selected by X86 architecture hence "X86 && PCI" does
not make it better.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
There is an example in the VIDEO_PCI_DEFAULT_FB_SIZE help text to
tell people how to calculate its value but the resolution given
does not match the value. Fix it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the driver is legacy free, remove the x86 dependency so
that it can be used on non-x86 architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
At present the driver uses IO instructions to access the legacy
VGA IO ports, which unfortunately limits the driver to work only
on x86. It turns out the IO instruction is not necessary as Bochs
VGA card remaps the legacy VGA IO ports (0x3c0 -> 0x3df) to its
memory mapped register space from offset 0x400.
Update the driver to use MMIO access for VGA IO port.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
bochs_vga_write() takes 'index' as one argument, but never uses it.
While we are here, use macros instead of magic numbers for the
VGA IO port register name and value.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
The driver does not call any MTRR APIs.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Some coding convention fixes for video_post_bind().
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Show the number of records in the table and the total table size in
bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function used to be for adding a list of requests to be actioned on
relocation. Revert it back to this purpose, to avoid problems with boards
which need control of their MTRRs (i.e. those which don't use FSP).
The mtrr_set_next_var() function is available when the next free
variable-MTRR must be set, so this can be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: 3bcd6cf89e ("x86: mtrr: Skip MSRs that were already programmed..")
Fixes: 596bd0589a ("x86: mtrr: Do not clear the unused ones..")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On Coral U-Boot SPL programs some MTRRs and FSPv2 in U-Boot proper
needs to program MTRRs too. With current testing logic of mtrr
commit in init_cache_f_r(), the mtrr commit is skipped which won't
work as the queued mtrr requests include setup for DRAM regions.
Change the logic to allow such configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tweak to put back CONFIG_FSP_VERSION2 at top:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Update dwc3 generic driver and update support for rk3568/rk3328;
- Add boards:
rk3566: Pine64 Quartz64-A/B, SOQuartz on Model A/Blade/CM4-IO
rk3568: Radxa E25 Carrier Board
rk3588: Radxa ROCK5A
- Fixes and updates for chromebook veryon/jerry/speedy;
- SPI support fixes for rk3399/rk3568/rk3588;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Handle USB480M clock ID in set_rate() and set_parent()
to allow the dt assigned-clocks and assigned-clock-parents
work on rk3328.dtsi
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB2.0 Host and OTG controllers in RK3328 are using USB2PHY.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB 3.0 in all RK3328 boards.
=> usb start
starting USB...
Bus usb@ff5c0000: ehci_generic usb@ff5c0000: Failed to get clocks (ret=-19)
Port not available.
Bus usb@ff5d0000: USB OHCI 1.0
Bus usb@ff600000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@ff580000: 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
1 Hub (480 Mb/s, 0mA)
U-Boot Root Hub
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like Rockchip RK3568, the RK3328 also have single node to
represent the glue and ctrl for USB 3.0.
So, use the driver data to use single ctrl for RK3328 DWC3.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Driver support for rk3328 is not supported so drop this
unused XHCI_DWC3.
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3328-xhci has been added due to the fact that the upstream
dwc3 is unsupported. Moreover, the driver for rk3328-xhci is
not added to the code tree.
By considering these facts and unsupported rk3328-xhci this
patch is dropping all related code from DT. However, the DWC3
is fixed now in dwc3-generic and RK3328 USB 3.0 is functional
in upcoming patches.
Let's drop it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A quick power cycle of a LDO regulator during dw-mmc signal voltage
change has shown that SD-card does not always get recognized.
Linux driver use an enable_time of 400us for LDO regulators. Apply a
500us delay when a LDO regulator is enabled to fix possible issues.
Fixes: 94afc1cb46 ("power: regulator: rk8xx: update the driver for rk808 and rk818")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: elaine.zhang<elaine.zhang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).
Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
gpio_request_list_by_name() returns the number of gpios requested.
Notably it swallows the underlying -ENOENT when the "gpios" property
does not exist.
Update the i2c-gpio driver to check for ret == 0 before trying the new
sda-gpios/scl-gpios properties.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move bootph-all prop to common SoC dt file, because they are typically used
by multiple boards.
Unreferenced nodes are removed from the SPL device tree during a
normal build.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pcie pinctrl override added in the commit a76aa6ffa6 ("rockchip:
rk3568-rock-3a: Enable PCIe and NVMe support") is causing a pinmux issue
on linux when using a EFI boot flow.
The pcie reset-gpios must however be configured with gpio function, or
the device will freeze running pci enum and nothing is connected.
Adjust the pinctrl override in u-boot.dtsi to fix this issue. PCIe/NVMe
continues to work in both U-Boot and linux after this change.
Also revert disable of sdmmc2 and uart1 to fix use of wifi in linux when
using a EFI boot flow.
Fixes: a76aa6ffa6 ("rockchip: rk3568-rock-3a: Enable PCIe and NVMe support")
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.
Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.
Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update documentation on how to write a bootable u-boot-rockchip-spi.bin
image into SPI flash. This removes the reference to a hardcoded and now
obsolete 0x60000 payload offset.
Also remove an obsolete reference to pad_cat.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootRom will try to load TPL+SPL from media in the following order:
- SPI NOR Flash
- SPI NAND Flash
- NAND Flash
- eMMC
- SDMMC
SPL will try to load FIT from media in the order defined in the device
tree u-boot,spl-boot-order property.
Change the default order to load FIT from to:
- same media as TPL+SPL
- SDMMC
- eMMC
Boards with strict load order requirements should override the
u-boot,spl-boot-order property in the board specific u-boot.dtsi.
Fixes: 42f67fb51c ("rockchip: rk3568: Fix boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
