Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
No more use static frequency HSI = 64MHz for STGEN clock
but HSE (with higher accurency) by default.
Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency
is provided at boot by BootRom and cp15 cntfrq and modified
during clock tree initialization if needed.
When HSI is no more used by any device, this internal
oscillator can be switched off to reduce consumption.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The STGEN is the clock source for the Cortex A7 arch timer.
So after modification of its frequency, CP15 cntfreq is updated
and a new timer init is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Manage dynamic value for armv7 arch clock timer,
when CONFIG_SYS_HZ_CLOCK is not defined.
Get frequency from CP15 cntfrq information, initialized for example
by first boot stage, clock driver or by BootRom.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Modifying the default environment via CONFIG_EXTRA_ENV_SETTINGS is
somewhat inflexible, partly because the cpp language does not allow
appending to an existing macro. This prevents reuse of "environment
fragments" for different boards, which in turn makes maintaining that
environment consistently tedious and error-prone.
This implements a Kconfig option for allowing one to define the entire
default environment in an external file, which can then, for example, be
generated programmatically as part of a Yocto recipe, or simply be kept
in version control separately from the U-boot repository.
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Bootrom loads SPL from SDCARD or eMMC
according BootPin selection.
Then SPL loads U-Boot on the same mmc device
with the following predefined GPT partitioning:
on SDCARD: gpt partitioning
1: SPL
2: SPL#2
3: U-Boot
4: bootable partition
on eMMC:
The 2 boot partitions are used for SPL (2 copy)
boot1: SPL
boot2: SPL#2
The user partition use gpt partitioning
1: U-Boot
2: bootable partition
This patch select the correct SPL partition
(3 for SDCARD on mmc0 and 1 for eMMC on mmc1)
according the BootRom information saved in TAMP register
and based on configuration flasg:
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
=> for BOOT_DEVICE_MMC1 or mmc 0 in U-Boot
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2 (new)
=> for BOOT_DEVICE_MMC2 or mmc 1 in U-Boot
And the correct boot_targets is selected according the environment
variables boot_device and boot_instance, with preboot command,
to search the bootable partition with kernel on this device
(generic distro support).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The spl_boot_partition function has been added in order to have
the possibility to boot on a same binary from different mmc devices
with different partitions.
By default keep the current behavior, SPL use the partition defined
by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Adds devicemodel support to the ISL1208 driver.
This patch drops the non-dm API as no board was using it anyway.
Also add it to Kconfig.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The mxsimage utility fails to compile against LibreSSL version < 2.7.0
because LibreSSL says it is OpenSSL 2.0, but it does not support the
complete OpenSSL 1.1 interface.
LibreSSL defines OPENSSL_VERSION_NUMBER with 0x20000000L and therefor
claims to have an API compatible with OpenSSL 2.0, but it implements
EVP_MD_CTX_new(), EVP_MD_CTX_free() and EVP_CIPHER_CTX_reset() only
starting with version 2.7.0, which is not yet released. OpenSSL
implements this function since version 1.1.0.
This commit will activate the compatibility code meant for
OpenSSL < 1.1.0 also for LibreSSL version < 2.7.0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonathan Gray <jsg@jsg.id.au>
We should not evaluate the value of reg before its value is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The boot scripts for booting from ramdisk are using
${fdtimage} when they really should be using ${fdtaddr}
This patch will fix it so the RAMdisk bootscripts operate
correctly.
Signed-off-by: Adam Ford <aford173@gmail.com>
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Prevent EMIF control of DDR_RESET line on DDR3 am43xx platforms for
am43xx_evm_rtconly_config. Without this DDR is unstable and can become
corrupted after multiple iterations of RTC+DDR mode.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[j-keerthy@ti.com Ported to latest master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable NETCONSOLE by default. Still requires changes to the boot
environment to enable on the platform.
Signed-of-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
NETCONSOLE isn't compiled in with SPL, so the include file needs to recognize that.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.
https://beagleboard.org/pocket
This was tested using the am335x_evm_usbspl_defconfig.
Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In preparation of migration to DM watchdog, clean up a bit.
The 8xx watchdog really is a HW watchdog, so declare it as is
then it goes through Kconfig
And the watchdog reset doesn't mind getting interrupted, so
no need to disable interrupts
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
reginfo is redundant with some of the commands in immap.c, so
move reginfo into that file and remove duplicated info.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Latest versions of u-boot have increased in size and require more
than the 256kb allocated to it.
The MCR3000 board is equipped with an AM29LV160DB boot flash which
is organised as follows:
- One 16kb block
- Two 8kb block
- One 32kb block
- Thirty one 64kb blocks
At the time being, u-boot is a single piece occupying the 256 first
kbytes, then the environment is stored in the following 64kb block
The environment being quite tiny, we save one 64kb block by embedding
the environment in the first 8kb block, hence allowing to increase
the monitor size to 320kb.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Commit 7653942b10 ("common/env_embedded.c: drop support for
CONFIG_SYS_USE_PPCENV") dropped the .ppcenv section which was
used in linking scripts to allow fine placement of embedded
environment sections.
This implies that GCC randomly places objects from env/embedded.o
and environment is not guaranteed to be located at the correct address:
04003df8 g F .text 00000038 mii_init
04004000 g O .text 00000004 env_size
04004004 g O .text 00002000 environment
04006004 g F .text 00000040 .hidden __lshrdi3
This patch restores this capability by allocating each object marked
with __UBOOT_ENV_SECTION__ into a different section. Hence
'environment' will be alone in .text.environment, allowing a
fine placement in u-boot.lds with:
. = DEFINED(env_offset) ? env_offset : .;
env/embedded.o (.text.environment)
Fixes: 7653942b10 ("common/env_embedded.c: drop support for CONFIG_SYS_USE_PPCENV")
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Some config is redundant with Kconfig. Fix it.
Also remove unused configs
Move SDRAM_MAX_SIZE in the only place it is used
include/environment.h already defines CONFIG_ENV_SIZE
from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as
(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
remove BOOTARGS as bootargs is set by the different boot commands
Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in
line with CPM DPRAM organisation
Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and
CONFIG_SYS_INIT_SP_OFFSET which are unused
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Since commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data"), mtd_to_nand() has to be used instead
of mtd->priv
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
u-boot requires some RAM at startup, to store global data structure.
RAM is also needed when we migrate to DM for some initial malloc
This patch implements the proper init of that RAM by calling
board_init_f_alloc_reserve() and board_init_f_init_reserve()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Some malloc memory is needed at startup for DM model.
Lets reorganise the use of the CPM dpram.
The MPC866/885 dpram, we have 8kbytes dual port RAM, which is usable as:
IMMR + 0x2000..0x2800: BD/Data/Microcode
IMMR + 0x2800..0x2e00: BD/Data
IMMR + 0x2e00..0x3800: BD/Data/Microcode
IMMR + 0x3800..0x3a00: BD/Data
IMMR + 0x3a00..0x3c00: BD/Data/Microcode
IMMR + 0x3c00..0x4000: Parameters for the Peripheral Controllers
Lets reallocate all BDs in the 3800..3a00 area and give the full
2800..2e00 for dynamic RAM allocation including global data
That way, the microcode areas remain available if needed one day.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
SPRN_IMMR is defined regardless of the CPU. Therefore, there
is no point in enclosing get_immr() inside a #ifdef CONFIG_8xx
As it a static inline function, it will in any case only be
compiled in functons using it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Avoid hardcoding the PVR values in C since they are defined
in processor.h
At the same time, remove those multiple PVR values for 8xx and
keep only one that we call PVR_8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
In most places, immap local pointer is defined as
immap_t __iomem *immap = (immap_t __iomem *)CONFIG_SYS_IMMR;
In a few places, it is defined as
immap_t __iomem *immap = (immap_t __iomem *)(immr & 0xFFFF0000);
This patch replaces the few of the latest form by the other one.
The two are fully equivalent since SPRN_IMMR is set with CONFIG_SYS_IMMR
very early in start.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
commit 907208c452 ("powerpc: Partialy restore core of mpc8xx")
didn't bring back support for I2C on the mpc8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
All board configs are now enabled DM_SPI for SPL and
U-Boot proper, so now its time to drop non-dm code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
AT91 ma5d4evk board uses atmel spi driver, enable DM_SPI to
use dm functionality.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board.
usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
