This adds basic files for the sandbox board. The lds file is very simple
since we can rely mostly on the linker defaults.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:
http://en.qi-hardware.com/wiki/Ben_NanoNotehttp://en.qi-hardware.com/wiki/Main_Pagehttp://en.wikipedia.org/wiki/Qi_hardware
This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.
About USB boot tool
-------------------
Jz4740 is one of the XBurst processors with USB boot functionality
supported. The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.
USB boot tool is available to the public at Ingenic website. Also
there is an alternative Debian package named xburst-tools.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
An entry in the main Makefile for the mx31pdk board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
And various defines to enable NAND support and NAND spl code for the
P1010RDB platform.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds basic board support with DRAM and UART functionality
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.
Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Alessandro Rubini <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>
The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit
GmbH.
See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html
for detailed information about this device.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Fix board part of AT91SAM9261-EK according to the new scheme
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When booting from NAND we get the environment and FMan ucode from NAND.
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch add support for the Network Space v2 board and parents, based
on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2
and Internet Space v2.
Additional information is available at:
http://lacie-nas.org/doku.php?id=network_space_v2
Signed-off-by: Simon Guinot <sguinot@lacie.com>
This adds support for the keymile Kirkwood BEC portl2 board. This board
relies on the km_arm (km_kirkwood) BEC.
The egiga driver is configured for a 100M full-duplex, A/N off connnection
to the backplane. This board has always ethernet present, because it is
connected to the marvell switch similar to mgcoge3un. The reset_phy
functionality is also the same to mgcoge3un.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
suen3 and suen8 were in first HW version quite different, but
now they are from a u-boot point of view similar. So these
two boards can use the same header file. Other keymile boards
differ only in the usage of the PCI interface. Therefore
a target km_kirkwood_pci was introduced. All targets use
the same header file.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
I can't build test this, but just looking at the config files written
and it seems OK ...
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Minimal platform support to boot linux from SD.
Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.
We add the BootROM init file for the mgcoge3un memphis RAM.
We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.
After this change vision2 board can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: Jason Liu <jason.hui@linaro.org>
The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
The meesc board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The directory and file mgcoge was renamed to km82xx.
Because other keymile 82xx will follow and will use the
same platform code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: Eric Bénard <eric@eukrea.com>
- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
9260 (64MB RAM & nor boot)
9260_nand (64MB RAM & nand boot)
9G20_128M (128MB RAM & nor boot)
9G20_nand_128M (128MB RAM & nand boot)
(nor boot is using lowlevel init)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.
The board support is based on the BeagleBoard implementation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Jason Liu <r64343@freescale.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Au1x00 is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
IncaIP is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
All current CPUs and SoCs are based on MIPS32 arch. The complete
code resides in the global arch/mips/cpu directory. This is not
suitable if other MIPS architectures like MIPS64 or Octeon should
be supported in the future.
To achieve this the current CPU code is moved to its own mips32
subdirectory. All MIPS32 boards have to use mips32 as config switch
in board.cfg.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Position independant functionality is due for removal from the x86
architecture, so create two distinct configurations - One for Flash and
one for SRAM
We should have been defining the actual board name in the options, not
the processor. Fix this for P1011RDB, P1020RDB, P2010RDB, and P2020RDB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_QEMU_MIPS is already provided by <configs/qemu-mips.h>, so we
don't generate it using the options fields in boards.cfg.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
CONFIG_GTH2 is already provided by <configs/gth2.h>, so we don't
generate it using the options fields in boards.cfg.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.
This patch supports the following functions:
- 256MB DDR3-SDRAM
- SPI ROM
- Ethernet
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for Samsung s5pc210 universal board
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
Supported:
MMC
IDE
PMIC
SPI flash
LEDs
I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.
Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx
Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
