No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use pr_* log functions from Linux. They can be enabled/disabled
via CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixes a bug found on thuban boards, which were for 2 years in
a long-term test with varying temperatures. They showed
problems in u-boot when attaching the ubi partition:
U-Boot# run flash_self_test
Booting from nand
set A...
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
data abort
pc : [<87f97c3c>] lr : [<87f97c28>]
reloc pc : [<8012cc3c>] lr : [<8012cc28>]
sp : 85f686e8 ip : 00000020 fp : 000001f7
r10: 8605ce40 r9 : 85f68ef8 r8 : 0001f000
r7 : 00000001 r6 : 00000006 r5 : 0001f000 r4 : 85f6ecc0
r3 : 00000000 r2 : 44e35000 r1 : 87fcbcd4 r0 : 87fc755b
Flags: nZCv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
Reason is, that accidentially the U-Boot implementation
from __schedule_ubi_work() did not check the flag
ubi->thread_enabled and started with wearleveling work,
but ubi did not have setup all structures at this point
and crashes.
Solve this problem by splitting work scheduling and processing.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Heiko Schocher <hs@denx.de>
Previous patch for this driver breaks i2c initialization.
commit 8bcf12ccce ("i2c: mvtwsi.c: Avoid NULL dereference")
If actual_speed is passed as NULL in this function:
static void __twsi_i2c_init(struct mvtwsi_registers *twsi, int speed,
int slaveadd, uint *actual_speed)
than __twsi_i2c_set_bus_speed never get called. This causes i2c clock
to run on default speed - 2MHz (measured with oscilloscope). This is issue
on some boards, sunxi for example, since on I2C0 bus PMU is connected.
The bootlogs with and without the patch are as follows:
Wihtout the patch:
U-Boot SPL 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200)
DRAM: 1024 MiB
Failed to set core voltage! Can't set CPU frequency
Trying to boot from FEL
U-Boot 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
With the patch:
U-Boot SPL 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from FEL
U-Boot 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dtc produces these warnings when compiling sandbox:
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Could not get phandle node for /base-gpios:num-gpios(cell 0)
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Missing property '#gpio-cells' in node /reset-ctl or bad phandle
(referred from /extra-gpios:num-gpios[0])
Both are due to it assuming that the 'num-gpios' property holds a phandle
pointing to a GPIO node.
To avoid these warnings, rename the sandbox property so that it does not
include the string 'gpios'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the whole map/unmap_physmem stuff and just use the address
already obtained from DT in ofdata_to_platdata(), instead of
repeating that, wrongly, in probe.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix minor checkpatch warning about udelay(3000) being too long
and should be replaced by mdelay(3).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Drop the len variable, it's useless.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Inline this variable which is quite useless.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The IIC on Gen2 is compatible with this driver as well, allow it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This driver is no longer used on any supported platform in U-Boot and
there is no interest in maintaining it further from people that have
used it historically.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
c: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Fix build warning in drivers/video/ivybridge_igd.c with gcc 7.3.0:
warning: 'ivb_pm_gt2' defined but not used [-Wunused-const-variable=]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the following statements
if (a) return a; if (a) return c;
the second return can never be executed.
Identified by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To make this driver easier to be reused, dual-license DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Extend the instantiate_rng() function and the corresponding CAAM job
descriptor to instantiate all RNG state handles. This moves the RNG
instantiation code in line with the CAAM kernel driver.
Previously, only the first state handle was instantiated. The second
one was instantiated by the CAAM kernel driver. This works if the
kernel runs in secure mode, but fails in non-secure mode since the
kernel driver uses DEC0 directly instead of over the job ring
interface. Instantiating all RNG state handles in u-boot removes the
need for using DEC0 in the kernel driver, making it possible to use
the CAAM in non-secure mode.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: York Sun <york.sun@nxp.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no value to enable phylib without networking support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On detach UBI attempts to update fastmap after closing user interfaces
but at this point UBI volumes have already been free()'ed and fastmap
can no longer access these data structures.
Signed-off-by: Martin Townsend <mtownsend1973@gmail.com>
Cc: hs@denx.de
Cc: kmpark@infradead.org
Cc: richard@sigma-star.at
For '#ifndef CONFIG_DM_I2C' twsi_i2c_init() passes NULL as
4th parameter to __twsi_i2c_init().
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make the ihs_i2c driver DM-compatible; for legacy boards, the old functions are
retained within #ifdefs.
No board uses the new DM driver yet; this patch only lays the foundation for
future support.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Prepare the function interface of the ihs_i2c driver for DM conversion
in a future patch.
While we're at it, fix some style violations, and make the code more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Some functions in the fsl_i2c driver are declared as inline, even though
they are quite large, which needlessly increases the size of the
resulting binary.
This patch removes the inline declarations.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Fix some style violations in the fsl_i2c I2C driver, and use shorter
type names for variables in some cases.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
'default' on a choice refers to the symbol selected by default, not to
the choice mode, so 'default n' is meaningless.
No functional changes. Optional choices implicitly default to n mode
(and there is no way to make them default to another mode).
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection n (undefined) of <choice> (defined at drivers/usb/ulpi/Kconfig:3) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int. For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long. For the long term
we should however change the declaration of dma_buf.
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
After enabling TrustZone various parts of the CAAM silicon become
inaccessible to non TrustZone contexts. The job-ring registers are designed
to allow non TrustZone contexts like Linux to still submit jobs to CAAM
even after TrustZone has been enabled.
The default job-ring permissions after the BootROM look like this for
job-ring zero.
ms=0x00008001 ls=0x00008001
The MS field is JRaMIDR_MS (job ring MID most significant).
Referring to "Security Reference Manual for i.MX 7Dual and 7Solo
Applications Processors, Rev. 0, 03/2017" section 8.10.4 we see that
JROWN_NS controls whether or not a job-ring is accessible from non
TrustZone.
Bit 15 (TrustZone) is the logical inverse of bit 3 hence the above value of
0x8001 shows that JROWN_NS=0 and TrustZone=1.
Clearly then as soon as TrustZone becomes active the job-ring registers are
no longer accessible from Linux, which is not what we want.
This patch explicitly sets all job-ring registers to JROWN_NS=1 (non
TrustZone) by default and to the Non-Secure MID 001. Both settings are
required to successfully assign a job-ring to non-secure mode. If a piece
of TrustZone firmware requires ownership of job-ring registers it can unset
the JROWN_NS bit itself.
This patch in conjunction with a modification of the Linux kernel to skip
HWRNG initialisation makes CAAM usable to Linux with TrustZone enabled.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@nxp.com>
Link: https://github.com/OP-TEE/optee_os/issues/1408
Link: https://tinyurl.com/yam5gv9a
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a new driver for RX8010SJ rtc chip. The driver implements both
formats of U-Boot driver model.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Implement programming MAC address to the hardware, i.e. external flash
seen as EEPROM.
MAC address is only written if it differs from what is already stored in
flash or if reading the current MAC address fails.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Split the implementation of e1000_read_mac_addr into eeprom and register
versions called by e1000_read_mac_addr.
This allows for calling e1000_read_mac_addr when MAC address is needed
with no constraints where it is read from, and for calling the register
and, especially, the eeprom version directly in order to specify where
to read the address from.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Port functions for writing to EEPROM, updating the checksum and
committing data to flash from the Linux kernel igb driver.
Functions were ported from Linux 4.8-rc2 (694d0d0bb20).
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When building for 64bits system, we get some warnings about type
cast between pointer and integer. This patch eliminates the warnings
by using ulong/long type which is 32bits on 32bits system or 64bits on
64bits system.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The MIB RAM and FIFO receive start register does not exist on
i.MX8M. Accessing these register will cause system hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX8M OCOTP follow same flow as i.MX6Q, but it has 64 banks
and each bank 4 words.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Each uclass has a driver name which we can use to look up the uclass. This
is useful for logging, where the uclass ID is used as the category.
Add a function to handle this, as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This converts the following to Kconfig:
CONFIG_SYS_OMAP24_I2C_SLAVE
CONFIG_SYS_OMAP24_I2C_SPEED
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
DDR controllers always use binding register to determine the memory
space to perform data initialization. In case of controller interleaving,
the space is doubled, resulting twice long wait. It wasn't too bad until
the memory capacity increases. To reduce the wait time, reduce the
binding space to half and restore it after data initialization.
Three-way interleaving is no longer used and is removed.
Signed-off-by: York Sun <york.sun@nxp.com>
DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.
Signed-off-by: York Sun <york.sun@nxp.com>
On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.
Signed-off-by: York Sun <york.sun@nxp.com>
For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.
Signed-off-by: York Sun <york.sun@nxp.com>
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
U-Boot on QEMU does not build ACPI table by ourself, instead it uses
the prebuilt ACPI table via the qfw interface. This implements the
qfw version of acpi_get_rsdp_addr() for setup_zimage().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Arasan NFC driver requires the self-init mode,
so it should select it.
Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the ecc address calculation before updating
to ecc register. The ecc address has to be calculated based on
page, oob and ecc sizes of the device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for ondie ecc. As of now
this adds support for micron parts which supports
ondie ecc.
Didn't found any better way to detect ondie ecc
support by a device except sorting out with
manufacture and device id's.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move common part of ecc structure initialization to
arasan_nand_init() routine.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When we have a driver that is used on both 32bit and 64bit targets and
we are talking about address space we cannot use u64 nor u32 and instead
need to use phys_addr_t.
Fixes: 377883f16d ("net: mvpp2x: fix phy connected to wrong mdio issue")
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Since 'commit f4fcba5c5b ("clk: implement clk_set_defaults()")'
STM32F4 family board can't boot.
Above patch calls clk_set_rate() for all nodes with assigned-clock-rates
property. Clock driver for STM32F family doesn't implement .set_rate
callback which make clk_set_defaults() exit on error and prevent board
to boot.
Fixes: f4fcba5c5b ("clk: implement clk_set_defaults()")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit 608b0c4ad4 ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4 ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The variable cfi_flash_num_flash_banks is defined iff
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, but it is used
unconditionally in the function cfi_flash_init_dm. This leads to a
undefined variable compile error when CONFIG_SYS_MAX_FLASH_BANKS_DETECT
is not defined, but DM is enabled.
Fix this by always defining the cfi_flash_num_flash_banks variable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When long expressions surrounded by parentheses are split into multiple
lines, each consecutive line should be aligned with the corresponding
parenthesis. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Long lines (>80 characters) should be avoided where possible. Break up
some long lines where it's not detrimental to readability.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In a while loop in cfi_flash.c the array "start" is accessed at the index
"sector" before the index variable "sector" is bounds-checked, which
might lead to accesses beyond the bounds of the array.
Swap the order of the checks in the "&&" expression, so that the
short-circuit evaluation prevents out-of-bounds array accesses.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
checkpatch.pl complains about the spelling of ERR_TIMOUT. Since the
error is only used in a handful of files, we rename the error to
ERR_TIMEOUT.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Camel-case naming should be avoided. Rename two camel-case variables,
and fix their usage accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Strings should not be split accross multiple lines. Where possible and
not detrimental to readability, fix the instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
According to the C standard, pointer arithmetic for pointers of type
void is undefined behavior (the assumption that they're 8-bit wide is a
GCC-specific assumption). In the interest of keeping the code
standards-compliant, and also better communicate intent, switch all
void* variables where pointer arithmetic is used to u8* variables.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The condition in if statements should not be used for variable
assignment. Instead, the assignment should be done in a separate step
beforehand. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The opening brace of block statements should be attached to the
statement itself, and not be on a separate line.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
If in a loop, the if block in a if/else statement ends in a break, the
statements in the else blockcan be extracted, since the break stops the
execution.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In if/else statements, either both blocks (if and else) should have
braces or both blocks should not have braces, but mixed configurations
are discouraged. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
"==" and "!=" bind tighter than the boolean operators, so parentheses
around them in compound logical statements are unnecessary. Fix all
instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Comment blocks should end with a "*/" on a separate line, not with the
"*/" attached to the end of the last line of text. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
printf/debug statements should not include the file name as a hardcoded
string, but instead use the __func__ macro. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When splitting long logical statements across multiple lines, the
logical operators should be at the end of the lines. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Blocks with a single statement should not be enclosed in braces. Fix all
instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should be no consecutive blank lines, and no blank lines at the
end of blocks. But there should be blank lines between variable
declarations and code. Fix all instances where either occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should be spaces around operators, and no spaces between a cast
and the variable its being applied to. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
case statements should be at the same level of indent as the switch
keyword. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When casting to a pointer type, the asterisk should be attached to the
type name, not separated by a space. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should not be additional spaces when nesting parentheses
("( (...) )"). Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In a pointer declaration there should not be a space between the
asterisk and the pointer name. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should not be a space between a function name and a parenthesis
("func (...)"). Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Signed-off-by: Alexander Graf <agraf@suse.de>
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x mini-uart is only really usable as U-Boot serial output
when it is muxed to the UART pins of the RPi pin header.
So fail probing in case it is not muxed correctly, as in that case
firmware did not initialize it properly either.
Signed-off-by: Alexander Graf <agraf@suse.de>
The serial initialization doesn't always quite work for me, so let's
always skip it for now. We know that firmware on the RPi initializes
us properly already.
Signed-off-by: Alexander Graf <agraf@suse.de>
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently our serial device search chokes on the fact that the serial
probe function could fail. If it does, instead of searching for the next
usable serial device, it just quits.
This patch changes the fallback logic so that even when a serial device
was not probed correctly, we just try the next ones until we find one that
works.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Assuming mac_clk is fed by an external clock, set clk_rmii_src
clock select control register from IO for rgmii interface.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Set gmac pins iomux and rgmii tx pins to 12ma drive-strength,
clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The rk3328 soc has two gmac controllers, one is gmac2io,
the other is gmac2phy. We use the gmac2io rgmii interface
for 1000M phy here.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3399 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
simply ignore the set_rate() operation and return 0 to signal success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Linux uses the properties 'assigned-clocks', 'assigned-clock-parents'
and 'assigned-clock-rates' to configure the clock subsystem for use
with various peripheral nodes.
This implements clk_set_defaults() and hooks it up with the general
device probibin in drivers/core/device.c: when a new device is probed,
clk_set_defaults() will be called for it and will process the
properties mentioned above.
Note that this functionality is designed to fail gracefully (i.e. if a
clock-driver does not implement set_parent(), we simply accept this
and ignore the error) as not to break existing board-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Series-version: 2
Cover-letter:
clk: support assigned-clock, assigned-clock-parents, assigned-clock-rates
For various peripherals on Rockchip SoCs (e.g. for the Ethernet GMAC),
the parent-clock needs to be set via the DTS. This adds the required
plumbing and implements the GMAC case for the RK3399.
END
This implements the (newly added) set_parent() operation for the
RK3399 with a focus on allowing the RGMII clock parent to be
configured via the assigned-clock-parents property of the GMAC node.
This implementation supports only the GMAC (in fact only the RGMII
clock parent) and allows to set this clock's parent either to the
internal SCLK_GMAC or to an external clock input (identifiable by it
providing a 'clock-output-name' of "gmac_clkin").
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
The logic in clk_get_by_index() may be useful for other properties
than 'clocks': e.g. 'assigned-clocks' and 'assigned-clock-parents'
follows the same model.
This commit refactors clk_get_by_index() by introducing an internal
function clk_get_by_indexed_prop() that allows to specify the name
of the property to process. The original clk_get_by_index() call
is simply directed through this helper function with the property
name fixed to "clocks".
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Clocks may support multiple parents: this change introduces an
optional operation on the clk-uclass to set a clock's parent.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
PLLSAIP divider uses 2 bits (bits 16 and 17) into RCC_PLLSAICFGR
register, available combination are :
00: PLLSAIP = 2
01: PLLSAIP = 4
10: PLLSAIP = 6
11: PLLSAIP = 8
Previously, the divider value was incorrectly set to 6.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
All current STM32F4 supported boards uses a 8MHz external oscillator.
All current STM32F7 supported boards uses a 25MHz external oscillator.
In order to introduce the new stm32f429-evaluation board which uses a
25MHz external oscillator without creating a dedicated struct
stm32_clk_info for this board, retrieve the external oscillator
frequency from DT and set pll_m accordingly to obtain 1MHz for the VCO.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Clarify the computation precedence in two ternary operator
constructions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Finally, make the mpc8xxx driver capable of handling more GPIO devices;
this entails adding a special case for the MPC5121 SoC, and adding a set
of new compatible strings.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Rename the Kconfig option, structures (and their members), as well as
functions of the mpc85xx driver to include mpc8xxx to reflect the more
generic usage.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
In preparation to making the MPC85xx GPIO driver useable for a broader
range of SoCs, rename the driver file.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Make the pca953x_gpio driver compatible with a live device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The variable hcd_name is unsued, drop.
Cc: Marek Vasut <marex@denx.de>
Cc: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DM capable code into the SH ethernet driver and support probing
both from DT and pdata. The legacy non-DM, non-DT support is retained
as there are still systems in the tree which are not DM or DT capable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the legacy functions around, so that they can be wrapped in a
massive ifdef CONFIG_DM_ETH once DM support is added. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split sh_eth_init() function into smaller chunks, which can
be called from both DM and non-DM code while handling the
specifics of both configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull out the code for writing MAC address into the NIC into a
separate function, so it can be reused by both DM and non-DM
code. This is done in preparation for DM support, which handles
MAC address programming separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split sh_eth_recv into two functions, one which checks whether
a packet was received and one which handles the received packet.
This is done in preparation for DM support, which handles these
two parts separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pass sh_eth_dev structure around instead of eth_device, since the
later is specific to the legacy networking support. This change is
done in preparation for the DM addition.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add driver for the Renesas RCar PCIe controller present on Gen2 SoCs.
The PCIe on Gen2 is used both to connect external PCIe peripherals as
well as access the on-SoC USB EHCI controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add allwinner,sun50i-h5-pinctrl compatible for H5 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: remove external link and format commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The DFU code relies on the HASH config option. Make sure it is always there
by selecting it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add option to set spi controller clock frequency via device tree
using standard clock bindings.
Define dw_spi_get_clk function as 'weak' as some targets
(like SOCFPGA_GEN5 and SOCFPGA_ARRIA10) don't use standard clock API
and implement dw_spi_get_clk their own way in their clock manager.
Get rid of clock_manager.h include as we don't use
cm_get_spi_controller_clk_hz function anymore. (we use redefined
dw_spi_get_clk in SOCFPGA clock managers instead)
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
ehci_writel() swaps the arguments for address and value. One call
in ehci-mxs ignores that.
This fixes the warning:
drivers/usb/host/ehci-mxs.c: In function ?ehci_hcd_stop?:
drivers/usb/host/ehci-mxs.c:159:19: error: initialization makes integer from pointer without a cast [-Werror=int-conversion]
ehci_writel(tmp, &hcor->or_usbcmd);
^
arch/arm/include/asm/io.h:117:34: note: in definition of macro ?writel?
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/usb/host/ehci-mxs.c:159:2: note: in expansion of macro ?ehci_writel?
^~~~~~~~~~~
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Bool initializations should use true and false.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
This driver has been using printf() including filename since it was
added. Convert to using debug() instead.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Add macros for the DIV6P1 clock type, which is used on Gen2
and optionally also on Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Gen2 requires setting RMSTPCR before booting, while on Gen3 this
is thus far always zero. Split the tables so the RMSTPCR can be set
too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Extract the macros specific to Gen3 clock into a separate header.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all SoCs have the same PLL configuration options,
so make those PLL configuraion tables per-SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all drivers use the same IDs, so make those IDs per-driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace fdtdec_get_addr() with devfdt_get_addr() as the later one is
the current recommended practice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Fixes: 9546eb92cb ("mmc: fix the wrong disabling clock")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add the probe function to support the s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Make flash writes 32 bit aligned by using bounce buffers to deal with
non 32 bit aligned buffers.
This is required because as per TI K2G TRM[1], the external master is
only permitted to issue 32-bit data interface writes until the last word
of an indirect transfer. Otherwise indirect writes is known to fail
sometimes.
[1] http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This reverts commit 57897c13de.
Using bounce_buf.c to handle non-DMA alignment problems is bad as
bounce_buf.c does cache manipulations which is not required. Therefore
revert this patch in favour of local bounce buffer solution in the next
patch.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This reverts commit b63b46313e.
This commit changed cadence_qspi_apb to use bouncebuf.c, which invalidates
the data cache after reading. This is meant for dma transfers only and
breaks the cadence_qspi driver which copies via cpu only: data that is
copied by the cpu is in cache only and the cache invalidation at the end
throws away this data.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Adopt the Linux DT bindings. This also fixes an issue
with the indaddrtrig register on the Cadence QSPI
device being programmed with the wrong value for the
socfpga arch.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz. However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.
Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_probe_tail is now only called from spi_flash_probe, hence we
can merge its body into spi_flash_probe.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Remove a superfluous newline, and reduce the scope of a variable.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
A previous patch removed the spi_flash_probe_fdt function, which
contained the last call of the spi_setup_slave_fdt function, which is
now equally obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Commit ba45756 ("dm: x86: spi: Convert ICH SPI driver to driver model")
removed the last usage of the spi_flash_probe_fdt function, rendering it
obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
0efc024 ("spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT
node") added a helper function spi_base_setup_slave_fdt to to set up a
SPI slave from a given FDT blob. The only user was the exynos SPI
driver.
But commit 73186c9 ("dm: exynos: Convert SPI to driver model") removed
the use of this function, hence rendering it obsolete.
Remove this function, as well as the CONFIG_OF_SPI option, which guarded
only this function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
This patch fixes a printf specifier style violation, reduces the scope
of a variable, and turns a void pointer that is used with pointer
arithmetic into a u8 pointer.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The hash command function were not flushing the dcache before passing data
to CAAM/DMA and not invalidating the dcache when getting data back.
Due the data cache incoherency, HW accelerated hash commands used to fail
with CAAM errors like "Invalid KEY Command".
Check if pbuf and pout buffers are properly aligned to the cache line size
and flush/invalidate the memory regions to address this issue.
This solution is based in a previous work from Clemens Gruber in
commit 598e9dccc7 ("crypto/fsl: fix BLOB encapsulation and
decapsulation")
Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sets DDR configuration parameter cdr1 before all other settings
to support case 0.9v VDD is enabled for some SoCs
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This time around we have a lot of EFI patches from Heinrich.
Highlights are:
- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XZ4q
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-01-23
This time around we have a lot of EFI patches from Heinrich.
Highlights are:
- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements
This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices
For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol
The uclass provides the bind, start, and stop entry points for the driver
binding protocol.
In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.
The EFI block driver binds to controllers implementing the block io
protocol.
When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.
The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.
A usage example is as following:
U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.
Now the EFI block driver installs the partitions with the simple file
protocol.
iPXE uses the simple file protocol to load Grub or the Linux Kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len]
Signed-off-by: Alexander Graf <agraf@suse.de>
This converts the following to Kconfig:
CONFIG_USB_MUSB_HCD
CONFIG_USB_MUSB_UDC
CONFIG_USB_DAVINCI
CONFIG_USB_OMAP3
CONFIG_USB_DA8XX
CONFIG_USB_AM35X
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY
Signed-off-by: Adam Ford <aford173@gmail.com>
flags member of struct timing was not initialized,
this took to unpredictable behaviour of display flags,
such DISPLAY_FLAGS_HSYNC_HIGH instead of _LOW etc.
Init timing->flags = 0
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76a ("mmc: disable the mmc clock during power off")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
During the tuning, drivers repeat data transfer, changing timing
parameters in the controller hardware. So, the tuning commands
(CMD19 for SD, CMD21 for eMMC) fail, and this is not a problem
at all.
Showing "Error detected..." in normal operation just make users
upset. This should not be shown.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This line overwrites host_cap that has been set by drivers and/or
helpers like mmc_of_parse(). Accumulate capabilities flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You must fix your DT if it specifies insane bus-width, for example,
bus-width = <3>;
debug() is not displayed in usual configuration, so people will not
even notice weirdness. Use dev_err() instead, then let it fail.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc_of_parse() in U-Boot is a pussy helper; it sets cfg->f_max to
52MHz even if DT does not provide "max-frequency" at all. This can
overwrite cfg->f_max that may have been set to a reasonable default.
As the DT binding says, "max-frequency" is an optional property.
Do nothing if DT does not specify it. This is the behavior of
mmc_of_parse() in Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
dev_read_u32_default() always returns something even when the property
is missing. So, it is impossible to do nothing in the case. One
solution is to use ofnode_read_u32() instead, but adding dev_read_u32()
will be helpful.
BTW, Linux has an equvalent function, device_property_read_u32();
it is clearer that it reads a property. I cannot understand the
behavior of dev_read_u32() from its name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Judging from its name and parameters, device_is_compatible looks like it
is compatible with a live device tree, but it actually isn't.
Make it compatible with a live device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There are some whitespace-related style violations in read.c; fix those.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The Makefile entries in the clk driver directory were not alphabetically
sorted. Correct this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The clk uclass was converted to support a live device tree recently,
hence the global data pointer declarations are no longer needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
checkpatch.pl complains that the clk_ops structures used in clk-uclass.c
ought to be const, so we mark them as const.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The function dev_read_addr calls ofnode_get_addr_index in the live tree
case, which does not apply bus translations to the address read from the
device tree. This results in illegal addresses on boards that rely on
bus translations being applied.
Fix this situation by applying bus translations in the live tree case as
well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Stephen Warren <swarren@nvidia.com>
Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for simple memory fill operation. With large data sizes
it is much faster to use EDMA for memory fill rather than CPU.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the calculation for tWR and tPD. This improves the DDR refresh
interval and brings the initialization into line with the binary blobs
currently being supplied by Marvell.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The RD_SAMPLE_DELAY field is 5 bits so it needs to be masked with 0x1f
instead of 0xf. Rather than checking the read sample delay for all DDR
chip selects use the values for the chip selects that are actually
configured. Finally continue searching for the max_phase value even if the
current read_sample is the same as the max_read_sample.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The ternary operation had the HIGH/LOW values the
wrong way round. Update it to use the correct value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When using only a single DDR chip select only assert M_ODT[0] on write.
Do not assert it on read and do not assert M_ODT[1] at all. Also set
tODT_OFF_WR to 0x9 which contradicts the recommendation from the
functional spec but is what Marvell's binary training blob does and
seems to give better results when ODT is active during writes.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Update default AXI, TUN, ARC clock set options:
instead of changing only IDIV divider settings adjust also domain PLL
settings.
Add support of TUN_ROM and TUN_PWM clocks (subclocks of TUNN_PLL)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8,
4 is not valid. The seq number could be configured by alias node.
The following patch will use i2c4 as the begin for i.MX7ULP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Identify and distinguish between platform device type of MX7ULP
and LS1021A.
This is a fix to commit 7edf5c45("serial: lpuart: add i.MX7ULP
support").
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When we using network on board using sh-eth, it prints a lot of
"CACHE: Misaligned operation at range" messages.
This commit fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This changes Change structure used in sh_eth_read and sh_eth_write function
from struct sh_eth_dev to struct sh_eth_info. This is necessary to convert
to Driver Model.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
bd_t is not used in sh_eth_config(). This deletes bd_t from sh_eth_config()
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the chord style checked by checkpatch.pl.
Details of change details are as follows:
- Fix typo
Change from alligned to aligned.
- Remove whitespace before ','
- Add spaces preferred around that '|'
- Fix missing a blank line after declarations
- Remove space after a cast declaration
- Fix format of block comments
- Add a blank line after function/struct/union/enum declarations
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a b53_reg read/write command which allows inspecting the switch
registers. Because the Broadcom BCM53xx registers have different sizes,
we need to split the accesses in 8, 16, 32, 48 or 64 bits to obtain
expected results.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure that we pad small packets to a minimum length of 60 bytes
(without FCS). This is necessary to interface with Ethernet switches
that will reject RUNT frames unless padded correctly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.
This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This implementation manages several clocks, disable and
free all of them in case of error during probe and in remove
callback.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes a problem in the mvneta driver where if more than
one packet arrives between calls to mvneta_recv(), the additional
descriptors will be marked as free even though only one descriptor
has been read and processed from the receive queue. This causes
the additional packet(s) to be delayed until the next packet arrives.
>From this point on all packets will be delayed because the receive
queue will contain unprocessed packets but the hardware shows no
busy descriptors.
Signed-off-by: Jason Brown <jason.brown@apcon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the return value is a signed int, if the leading MSB of rdreg is a 1,
it will get signed extended and will return a negative value which is an
error even though we read the correct value.
Fixes: dfcc496ed7 ("net: mii: Changes not made by spatch")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
