Commit graph

86 commits

Author SHA1 Message Date
Andrew F. Davis
c1c564af52 arm: mach-keystone: Use appended original image size in image processing
When an image is signed/encrypted on K2 devices the image may get padded
to meet alignment requirements for the signature/encryption type. The
original size is appended as 4 bytes little-endian to the end of the
final image.

Normally the trailing extra bytes are ignored and so restoring the
exact original size is not important. In the case of initrd the
original size is important as the kernel uses it to look for
additional filesystem data and can do the wrong thing when the
size is not correct.

Read off the original size and report it back from the image post
processing stage.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-29 17:58:52 -04:00
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00
Murali Karicheri
f748ec9d32 ARM: k2g: add a workaround to reset the phy
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12 08:05:46 -04:00
Murali Karicheri
c7206e9789 ARM: k2g-ice: Add pinmux support for rgmii interface
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default

As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12 08:05:45 -04:00
Vignesh R
91dba55ca6 soc: keystone: Merge into ti specific directory
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-11 20:07:12 -04:00
Jean-Jacques Hiblot
1514244cc1 ti: remove usage of DM_I2C_COMPAT and don't disable DM_I2C in SPL
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone

boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 07:15:21 +01:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Lokesh Vutla
8a8af8a2fd cmd: ti: Generalize cmd_ddr3 command
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7  platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
5cd9661dc6 arm: keystone: Move cmd_ddr3 to a common place
Move cmd_ddr3 to cmd/ti in order to make
it build for non-keystone TI platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rename to ddr3.c not cmd_ddr3.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:26 -05:00
Rex Chang
4849d95407 board: ti: K2G FC SoC 1GHz and DDR3 1066 MT/s support
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.

The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.

Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.

Modified findfdt script in u-boot environment variable to include new k2g board type.

Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:24 -05:00
Jean-Jacques Hiblot
f844d5f4e6 omap: Update the base address of the MMC controllers
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.

Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Srinivas, Madan
94f536fc4f arm: mach-keystone: Fixes issue with return values in inline assembly
The inline assembly functions in mon.c assume that the caller will
check for the return value in r0 according to regular ARM calling
conventions.

However, this assumption breaks down if the compiler inlines the
functions. The caller is then under no obligation to use r0 for the
result.

To fix this disconnect, we must explicitly move the return value
from the smc/bl call to the variable that the function returns.

Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-26 11:26:52 -04:00
Madan Srinivas
1d73ce6f68 arm: mach-keystone: Updates mon_install for K2G HS
On early K2 devices (eg. K2HK) the secure ROM code does not support
loading secure code to firewall protected memory, before decrypting,
authenticating and executing it.

To load the boot monitor on these devices, it is necessary to first
authenticate and run a copy loop from non-secure memory that copies
the boot monitor behind firewall protected memory, before decrypting
and executing it.

On K2G, the secure ROM does not allow secure code executing from
unprotected memory. Further, ROM first copies the signed and encrypted
image into firewall protected memory, then decrypts, authenticates
and executes it.

As a result of this, we cannot use the copy loop for K2G. The
mon_install has to be modified to pass the address the signed and
encrypted secure boot monitor image to the authentication API.

For backward compatibility with other K2 devices and K2G GP,
the mon_install API still supports a single argument. In this case
the second argument is set to 0 by u-boot and is ignored by ROM

Signed-off-by: Thanh Tran <thanh-tran@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-26 11:26:51 -04:00
Andrew F. Davis
9e58d4dbe3 arm: mach-keystone: Modify secure image size before copy
The size of the secure image does not include the size of the
header, subtract this out before we move the image or we grab
extra data after the image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-07-10 14:26:05 -04:00
Cooper Jr., Franklin
e5e546aad1 ARM: k2g: Program DDRPHY_DATX8 registers via mask and value variables
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:57 -04:00
Cooper Jr., Franklin
a76a6f3e04 ARM: k2g: Program DDR PHY MR2 register with the default value
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:57 -04:00
Cooper Jr., Franklin
f8b4a2d7e2 ARM: keystone2: Add additional fields used for DDR3 configuration
Future boards will need to configure DDR3 registers in a slightly
different manner. Support this by defining additional variables and
defines that will be utilized later.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:56 -04:00
Cooper Jr., Franklin
85bfe48b0a ARM: keystone2: Allow to build with all image formats
u-boot.bin is a copy of:
u-boot-fit-dtb.bin if CONFIG_FIT_EMBED is enabled,
u-boot-dtb.bin if CONFIG_OF_SEPARATE is enabled,
u-boot-nodtb.bin if DT is not enabled.
So, use u-boot.bin to to generate keystone images instead of
u-boot-dtb.bin

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:55 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Cooper Jr., Franklin
1743d040b1 ARM: keystone: Enable DM_I2C by default
Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:05:13 +02:00
Lokesh Vutla
ee3c6532be ARM: keystone2: Add support for getting external clock dynamically
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Lokesh Vutla
c5f177debc ARM: k2g: Add support for dynamic programming of PLL based on SYSCLK
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Madan Srinivas
2ff5183fba ARM: Keystone2: Build secure images for K2
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:05 -04:00
Vitaly Andrianov
e8d740f536 arm: mach-keystone: Implements FIT post-processing call for keystone SoCs
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.

The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:04 -04:00
Tom Rini
01abae4d04 Remove various unused interrupt related code
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused.  Rather than migrate
some of these options to Kconfig we just remove the code in question.

The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context.  In these cases we rename
and move the value local to the code in question.

Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:42:18 -04:00
Roger Quadros
752a8311e9 ARM: k2g: setup PRU ethernet MAC addresses
PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:57:15 -04:00
Nishanth Menon
4361220dae ARM: K2G: DDR3: Fix up priv ID for MPU
For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.

Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:10 -05:00
Andrew F. Davis
ac34286647 keystone2: Move target selection to Kconfig
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-11-28 15:10:34 -05:00
Lokesh Vutla
8b01ebd812 ARM: keystone2: PLL: Enable glitch free initialization sequence
Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].

[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:36 -05:00
Masahiro Yamada
43ebbfc39f ARM: keystone: rename clk_get_rate() to ks_clk_get_rate()
The KeyStone platform has its own clk_get_rate() but its prototype
is different from that of the common-clk (clk-uclass) framework.

Prefix the KeyStone specific implementation with ks_ in order to
avoid name-space conflict.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:13 -04:00
Masahiro Yamada
2846bd03ea ARM: keystone: remove declaration of unused functions
These two functions are neither defined nor referenced.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-07 14:26:35 +00:00
Lokesh Vutla
5d21406516 ARM: keystone2: Add support for parsing monitor header
Given that boot monitor image is being generated to a specific target location
depending on the SoC and U-boot relies on addr_mon env variable to be aligned
with boot monitor target location. When ever the target address gets updated in
boot monitor, it is difficult to sync between u-boot and boot monitor and also
there is no way to update user that boot monitor image is updated.

To avoid this problem, boot monitor image is being generated with mkimage
header. Adding support in mon_install command for parsing this header.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:10 -04:00
Lokesh Vutla
e1ae357d4b board: k2g: Enable ECC byte lane
Enable ECC byte lane for k2g-evm

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:07 -04:00
Masahiro Yamada
5d97dff042 treewide: replace #include <asm-generic/errno.h> with <linux/errno.h>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.

<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 22:25:27 -04:00
Karicheri, Muralidharan
bcdc1c8376 keystone: k2h/e/l: Fix DMA coherency for QM PDSP
commit 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.

Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.

Fixes: 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:05 -04:00
Lokesh Vutla
e2924e5904 ARM: k2g: Configure reset mux to device reset
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.

Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.

Right now to give a default watchdog behaviour "Device reset" is
being selected.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2016-06-02 21:42:19 -04:00
Nishanth Menon
2283284b05 ARM: keystone2: Add missing privilege ID settings
Add missing Privilege ID settings for KS2 SoCs.

Based on:
K2H/K: Table 6-7. Privilege ID Settings from SPRS866E (Nov 2013)
  http://www.ti.com/lit/ds/symlink/66ak2h14.pdf (page 99)
K2L: Table 7-7. Privilege ID Settings from SPRS930 (April 2015)
  http://www.ti.com/lit/ds/symlink/66ak2l06.pdf (page 71)
K2E: Table 7-7. Privilege ID Settings from SPRS865D (Mar 2015)
  http://www.ti.com/lit/ds/symlink/66ak2e05.pdf (page 75)
K2G: Table 3-16. PrivIDs from SPRUHY8 (Jan 2016)
  http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf (page 238)

Overall mapping:
-------+-----------+-----------+-----------+---------
PrivID | KS2H/K    | K2L       | K2E       | K2G
-------+-----------+-----------+-----------+---------
0      | C66x 0    | C66x 0    | C66x 0    | C66x 0
1      | C66x 1    | C66x 1    | Reserved  | ARM
2      | C66x 2    | C66x 2    | Reserved  | ICSS0
3      | C66x 3    | C66x 3    | Reserved  | ICSS1
4      | C66x 4    | Reserved  | Reserved  | NETCP
5      | C66x 5    | Reserved  | Reserved  | CPIE
6      | C66x 6    | Reserved  | Reserved  | USB
7      | C66x 7    | Reserved  | Reserved  | Reserved
8      | ARM       | ARM       | ARM       | MLB
9      | NetCP     | NetCP     | NetCP     | PMMC
10     | QM_PDSP   | QM_PDSP   | QM_PDSP   | DSS
11     | PCIe_0    | PCIe_0    | PCIe_0    | MMC
12     | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP
13     | Reserved  | Reserved  | PCIe_1    | Reserved
14     | HyperLink | PCIe_1    | HyperLink | Reserved
15     | Reserved  | Reserved  | TSIP      | Reserved
-------+-----------+-----------+-----------+---------

NOTE: Few of these might have default configurations, however,
since most are software configurable, it is better to explicitly
configure the system to have a known default state.

Without programming these, we end up seeing lack of coherency on certain
peripherals resulting in inexplicable failures (such as USB peripheral's
DMA data not appearing on ARM etc and weird workarounds being done by
drivers including cache flushes which tend to have system wide
performance impact).

By marking these segments as shared, we also ensure SoC wide coherency
is enabled.

Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:40 -04:00
Nishanth Menon
1f807a9f32 ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery
MSMC segment Privilege ID is not consistent accross the keystone2 SoCs.
As the first step to ensure complete SoC wide coherency setup, lets
refactor the macros to remove the #if-deffery around the code which
obfuscates which IDs are actually enabled for which SoC.

As a result of this change the PCIe configuration is moved after the
msmc configuration is complete, but that should ideally have no
functional impact.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:40 -04:00
Nishanth Menon
705c506e4f ARM: keystone2: Convert BOOT_SET_BITFIELD into static inline function
Fix up BOOT_SET_BITFIELD to be a static inline function to be readable
with the same functionality.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:11 -04:00
Nishanth Menon
f84e8e5b29 ARM: keystone2: Convert BOOT_READ_BITFIELD into static inline function
BOOT_READ_BITFIELD can easily be a static inline function and be a
little more readable with the same functionality.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:11 -04:00
Nishanth Menon
bc69b505f0 ARM: keystone2: Convert BOOTBITMASK to static inline function
BOOTBITMASK is almost impossible to decode, so convert it into a simpler
static line functions of equivalent solution.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:10 -04:00
Tom Rini
80485af243 ARM: keystone2: Only link cmd_ddr3.o on non-SPL builds
When we switch to including all linker lists in SPL it is important
to not include commands as that may lead to link errors due to other
things we have already discarded.  In this case simply move cmd_ddr3.o
over to the list with the rest.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:34 -04:00
Tom Rini
534bc70e35 ARM: keystone2: Switch to using the poweroff command
Now that we have a standard way to power off the hardware, switch to
using that rather than our own command.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:32 -04:00
Tom Rini
aadd3360e6 ARM: keystone2: Split monitor code / command code
When we switch to including all linker lists in SPL it is important
to not include commands as that may lead to link errors due to other
things we have already discarded.  In this case, we split the code for
supporting the monitor out from the code for loading it.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:15 -04:00
Vitaly Andrianov
8efc243741 ARM: keystone2: use detected ddr3a size
Because KS2 u-boot works in 32 bit address space the existing ram_size
global data field cannot be used. The maximum, which the get_ram_size()
can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size
to fix up dtb.

This commit introduces the ddr3_get_size() which uses SPD data to
calculate the ddr3 size. This function replaces the "ddr3_size"
environment variable, which was used to get the SODIMM size.

For platforms, which don't have SODIMM with SPD and ddr3 is populated to
a board a simple ddr3_get_size function that returns ddr3 size has to be
implemented. See hardware-k2l.h

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:45 -04:00
Vitaly Andrianov
d9a76e77c8 ARM: keystone2: use SPD info to configure K2HK and K2E DDR3
This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.

The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
ef76ebb1ef ARM: keystone2: K2G: Add support for different arm/device speeds
The maximum device and arm speeds can be determined by reading
EFUSE_BOOTROM register. As there is already a framework for reading this
register, adding support for all possible speeds on k2g devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
5cd1f6bd7a ARM: keystone2: Allow for board specific speed definitions
Its not compulsory that speed definition should be same on EFUSE_BOOTROM
register for all keystone 2 devices. So, allow for board specific
speed definitions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:43 -04:00
Suman Anna
f2a8279e76 ARM: keystone2: K2G: power-off DSP during boot
The DSPs are powered on by default upon a Power ON reset, and
they are powered off on current Keystone 2 SoCs - K2HK, K2L, K2E
during the boot in u-boot. This is not functional on K2G though.
Extend the existing DSP power-off support to the only DSP present
on K2G. Do note that the PSC clock domain module id for DSP on K2G
differs from that of previous Keystone2 SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:43 -04:00