Commit graph

30 commits

Author SHA1 Message Date
Jeroen Hofstee
878cae6b02 ARM: emif4: wait for CM_DLL_READYST to be set
The code intends for the CM_DLL_READYST to be set, but
actually polls till any bit is set since the logical
AND is used instead of the bitwise one is used. Fix it.

cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-07 19:42:33 -04:00
Tom Rini
87acf194a2 arm:am33xx: Make dram_init call sdram_init() in some contexts
We have two contexts for booting these platforms.  One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads.  The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL.  In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.

In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus).  In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Tom Rini
d0e6d34d7c am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOT
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build.  Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2014-04-17 17:24:40 -04:00
Dave Gerlach
b56b9a0884 ARM: AM43xx: Change DDR3 Reset Value
The bit DDR3_RST_DEF_VAL inside CTRL_DDR_IO represents the default value
of the ddr reset value for DDR3 before the EMIF takes over. We must have
this bit set high so that on exit from DeepSleep0 within the kernel the
reset line has the proper value.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2014-03-04 09:42:07 -05:00
Lokesh Vutla
d3daba10f1 ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:44 -05:00
Lokesh Vutla
965de8b91b ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18 21:14:18 -05:00
TENART Antoine
dcf846d5da Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Steve Kipisz
c5c7a7c32d am335x_evm: Add support to boot from NOR.
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on.  When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB.  We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.

We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Matt Porter
4fab8d7bbd am33xx: add dmm support to emif4 library
Adds a config_dmm() routine to support TI814X DMM configuration.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter
3ba65f97cb am33xx: refactor emif4/ddr to support multiple EMIF instances
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Peter Korsgaard
c00f69dbcd am33xx: support board specific ddr settings
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:38 -07:00
Tom Rini
d4898ea896 am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and support
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
318f27c98f am33xx: Rework config_ddr to make DDR3 support easier.
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values.  So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
942d3f0174 am33xx: Move some variables in emif4.c, mark them static.
We need vtpreg and ddrctrl but no longer need a second ddrregs.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
a74f0c7cb5 am33xx: Correct and clean up ddr_regs struct
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported).  Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove.  Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there.  Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
82afcc9efd am33xx: Do not touch 'ratio1' fields
The various ratio1 fields are not documented in any of the documentation
I can find.  Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
5ac3b7ada1 am33xx: Rework config_io_ctrl slightly
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation).  Rather than defining a struct and setting the
value repeatedly, just pass in the value.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
ff7ec0f945 am33xx: Use emif_regs struct for storing initialization values
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
87a1acbb69 am33xx: Turn a number of 'int' functions to 'void'
A number of memory initalization functions were int and always returned
0.  Further it's not feasible to be doing error checking here, so simply
turn them into void functions.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c48c895433 am33xx: Document what we're doing with ddrctrl->ddrckectrl
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
  we're operating in the normal mode where EMIF/PHY clock is controlled
  by the PHY.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c8da4a587c am33xx: Clean up unused DDR defines, prefix more with 'DDR2'
- Remove a handful of unused defines.
- Prefix more values with 'DDR2' as DDR3 will require different values.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
b971dfad6a am33xx: Move the call to ddr_pll_config, make it take the frequency
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value.  This call can be delayed
slightly to the point where we know which type of memory we have.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
fda35eb982 am33xx: Pass to config_ddr the type of memory that is connected
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()).  For now, pass in
the value of DDR2.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
bce58fece5 am33xx: Make config_cmd_ctrl / config_ddr_data take const structs
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const.  This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
10e7e36daf am33xx: Rework DDR2 EMIF initalization slightly
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Chandan Nath
62d7fe7c91 ARM:AM33XX: Add emif/ddr support
This patch adds AM33xx emif/ddr support along with board specific
defines.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00