The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move baseaddr to hardware.h to be shared between
configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
XPSS prefix was used in past and it is obsolete for quite
some time. Let's use correct SoC name which is Zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
T114 needs the SYSCTR0 counter initialized so the TSC can be
read by the kernel. Do it in the bootloader since it's a write-once
deal (secure/non-secure mode dependent).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Without this change, kernel fails at calling function cache_clean_flush
during kernel early boot.
Aprocryphally, intended for T114 only, so I check for a T114 SoC.
Works (i.e. dalmore 3.8 kernel now starts printing to console).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically
to any other Tegra30.
An alternative would be to simply remove the SKU checking from
tegra_get_chip_type(); most use of the value most likely simply wants
to know the current chip, not the specific SKU. Or, the function could
be split into separate tegra_get_chip() and tegra_get_sku() for the
cases where differentiation really is required.
I wonder whether tegra_get_chip_type() should printf() whenever any
unkown chip/SKU is found, although perhaps the function is called so
early that the printf() wouldn't actually make it to the UART anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The glitch in the SPI clock line, which commit 3cea335c34 (spi: mxc_spi: Fix spi
clock glitch durant reset) solved, is back now and itwas re-introduced by
commit d36b39bf0d (spi: mxc_spi: Fix ECSPI reset handling).
Actually the glitch is happening due to always toggling between slave mode
and master mode by configuring the CHANNEL_MODE bits in this reset function.
Since the spi driver only supports master mode, set the mode for all channels
always to master mode in order to have a stable, "glitch-free" SPI clock line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs. The timings need a slight
adjustment to be correct in all cases with later revs.
Signed-off-by: Tom Rini <trini@ti.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
After further testing we can run DDR at 400MHz so update the timings
again.
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Given that on TI814x we have MMC1/2 swapped, we also need to swap them
in MMC_BOOT_DEVICES_START/END
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang. This is why we have
a test currently for the boot mode being within range. The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.
Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).
Signed-off-by: Tom Rini <trini@ti.com>
Commit "8602114 omap: emif: configure emif only when required"
breaks SDRAM_AUTO_DETECTION.
The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection)
done in do_sdram_init(). The above commit moves dmm_init() above
do_sdram_init() because of which dmm_init() uses uninitialized
emif_sizes[].
So instead of using global emif_sizes[], get sdram details locally
and calculate emif sizes.
Reported-by: Michael Cashwell <mboards@prograde.net>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.
Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
This patch adds BCH8 ooblayout for NAND as provided by
0e618ef0a6a33cf7ef96c2c824402088dd8ef48c in linux kernel. This Layout is
currently only provided for 64 byte OOB.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.
Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the BCH result registers to register mapping for OMAP3 gpmc.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add generic api to get the frequency of the required peripherial. This
API gets the source clock frequency and returns the required frequency
by dividing with first and second dividers based on the requirement.
Test with command "sf probe 1:0; time sf read 40008000 0 1000".
Try with different numbers of bytes and see that sane values are obtained
Build and boot U-boot with this patch, backlight works properly.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add peripherial id for pwm inorder to support
generic api to get the clk frequency
Test with command "sf probe 1:0; time sf read 40008000 0 1000".
Try with different numbers of bytes and see that sane values are obtained
Build and boot U-boot with this patch, backlight works properly.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The 'XN' execute never bit is set in the pagetables. This will
prevent speculative prefetches to non executable regions. But the
domain permissions are set as master in the DACR register.
So the pagetable attribute for 'XN' is not effective. Change the
permissions to client.
This fixes lot of speculative prefetch aborts seen on OMAP5
secure devices.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Vincent Stehle <v-stehle@ti.com>
Cc: Vincent Stehle <v-stehle@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Introduce a weak version of dram_bank_setup function
to allow a platform specific function.
This is used in the subsequent patch to setup dram region
without 'XN' attribute in order to enable the region
under client permissions.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Vincent Stehle <v-stehle@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
We declare the set_section_dcache function globally in the cache header, for
later use by e.g. machine specific code.
Signed-off-by: Vincent Stehlé <v-stehle <at> ti.com>
Cc: Tom Rini <trini <at> ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SDIO1 (the SD-card slot on Dalmore) needs to have its pads setup
before the MMC driver is added.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add driver for tegra114 SPI controller. This controller is not
compatible with either the tegra20 or tegra30 controllers, so it
requires a new driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add a common interface to fdt based SPI drivers. Each driver is
represented by a table entry in fdt_spi_drivers[]. If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Move register structs from headers into .c files and use common name.
This is in preparation of making common fdt front end for SPI
drivers.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Rename tegra SPI drivers to tegra20_flash and tegra20_slink in
preparation for commonization and addition of tegra114_spi.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins. These boards were never manufactured, so
remove this support to clean up SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
AM33XX and TI814X have a similar mux though the pinmux register
layout and address space differ. Add a separate ti814x mux include
to support the TI814X-specific differences.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
