For some reasons shrouded in mystery, the code saving the FEL state was
saving the SCTLR register twice, with the second copy trying to justify
itself by using its ancient "control register" alias name.
Drop the redundant second copy, both from the fel_stash data structure,
and also the code saving and restoring it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Both the values and the MMIO addresses that we need during the 64-bit FEL
restore are smaller than 2^32, so we don't need to do any 64-bit loads.
Change the loads to only load 32 bits worth of data, that saves us some
bytes for storing the values.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When support for the Allwinner F1C100s SoC was originally introduced,
its DT lacked any MMC nodes, which upset our sunxi-u-boot.dtsi overlay,
when it tried to add an alias to the SD card. To quickly fix this back
then, we guarded that alias with a preprocessor macro.
Now the F1C100s family has gained MMC nodes, so we don't need the
special treatment anymore. Just remove this guard.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The SoC .dtsi originally submitted for the Allwinner F1C100s had the
wrong compatible string for the watchdog, which broke U-Boot's reset
functionality. To quickly fix this, we disable CONFIG_SYSRESET in
cfcf1952c1 ("sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), so that U-Boot's hardcoded reset driver could take over.
After this was properly fixed in the devicetree, we reverted that patch
in 92373de041 ("Revert "sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), however this line sneaked back in with d0ee7f295d
("Convert CONFIG_SYS_PBSIZE to Kconfig"), so during a Kconfig update.
Remove this line (again), to use the proper reset driver.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
- Merge in the final batch of CONFIG to Kconfig/CFG migration work. This
includes a fix for a number of ns16550 or similar UARTs due to a
migration bug. We also pull in a revert for enabling CONFIG_VIDEO on
tools-only_defconfig.
This reverts commit 1cfba53ca4.
Since commit 1cfba53ca4 ("config: tools only: add VIDEO to build
bmp_logo") the build of tools-only_defconfig fails:
| /bin/sh: line 1: tools/bmp_logo: No such file or directory
This has been noticed in OpenEmbedded and Debian [1].
Revert it for now.
[1] https://lists.denx.de/pipermail/u-boot/2023-January/504758.html
Signed-off-by: Fabio Estevam <festevam@denx.de>
Now that all remaining in-tree cases where we define or undef a CONFIG
symbol have been migrated to Kconfig or renamed to CFG we can make the
CI check more robust. We will exclude the doc, tools and arch/arm/dts
directories from this check as they are special cases. Further, we can
exclude the scripts/kconfig/lkc.h and include/linux/kconfig.h files as
the CONFIG values they define are special tooling cases and not real
symbols.
In the case of docs, the only places that currently fail this test are
old documentation that should be rewritten so that we can remove this
special case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In imx_watchdog, clean up the comment to just note the range now, as we
do not need to set the default here as Kconfig does this for us. For
ulp_wdog, set the default value via Kconfig instead.
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For this legacy driver, the only user sets these values in Kconfig, so
we can remove them from the header.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
listed in arch/Kconfig.nxp and match how they're currently used by
select'ing them under the required PowerPC ARCH_xxx options.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is used on both ARM and PowerPC platforms, this needs to be
asked in arch/Kconfig.nxp. Set the PowerPC defaults based on
arch/powerpc/include/asm/config_mpc85xx.h and remove the default set in
drivers/mtd/nand/raw/fsl_ifc_nand.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move
the comment from code to the help to explain what this does.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This variable has never been configured to another value at present, and
was not converted to Kconfig. Opt instead to rename this to
MUSB_TIMEOUT.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This is always defined to 5, so use that as the default.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
We can enforce the dependencies of this module via Kconfig now, so do so
rather than with #error statements. Further, we can ensure that all
required values are set to their defaults in Kconfig, and in fact
already do so, so remove the tests here. The exception is
CONFIG_UPDATE_LOAD_ADDR which needed to be migrated to Kconfig in the
first place.
Signed-off-by: Tom Rini <trini@konsulko.com>
In this case, using IS_ENABLED(...) to attempt to load the image results
in harder to read and less useful code, along with having to define a
CONFIG value that would be unused. To maintain the current albeit
slightly odd behavior, maintain that if we have both SPL_FS_FAT and
SPL_SATA_RAW_U_BOOT_USE_SECTOR enabled, we use SPL_FS_FAT for the load.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to not define a CONFIG value when the
CONFIG_AUTOBOOT_STOP_STR_* functionality is not enabled, rework the
assignment of empty and unused (as the code will be discarded under if
0, in the end) values to be AUTOBOOT_STOP_STR_* instead of
CONFIG_AUTOBOOT_STOP_STR_*.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the Linux code for "lib1funcs" has changed rather
dramatically. While a resync would be beneficial, it's outside the scope
of what we need here. Simply remove the define for CONFIG_AEABI and
tests for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Prior to commit 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to
Kconfig") we had defined CONFIG_SYS_NS16550_REG_SIZE to -1 with
DM_SERIAL such that we would then have a size 0 character array. This
resulted in functionally no padding. The confusion on my part came from
dealing with the constraints around platforms that do not use DM_SERIAL
in SPL/TPL. After Andre Przywara reported that sunxi was broken, I've
re-read the code and comments again and thought on this harder. What we
want I believe is what this patch does now.
If DM_SERIAL is defined for this stage, regardless of
CONFIG_SYS_NS16550_REG_SIZE then we will dynamically handle reg shifts
and 'struct ns16550' needs no padding (which is functionally what
unsigned char foo[0] provides). This is the same case as NS16550_DYNAMIC
and DEBUG_UART. Expand the existing comment here slightly.
Otherwise, we will have CONFIG_SYS_NS16550_REG_SIZE set to a non-zero
value, and handle padding within the struct.
Cc: Simon Glass <sjg@chromium.org>
Cc: Sergei Antonov <saproj@gmail.com>
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Fixes: 9591b63531 ("Convert CONFIG_SYS_NS16550_MEM32 et al to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
In order to avoid defining CONFIG_ARMV[78_]SECURE_BASE as empty in the
linker scripts, if not already defined, add and use
__ARMV[78_]SECURE_BASE for when the base is not defined and we want the
linker scripts to continue.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is used on both m68k, where CONFIG_SYS_IMMR is not used, and
PowerPC an ARM where it is. Abstract this to a new value rather than
re-defining a CONFIG symbol on m68k.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the code that adds the CapsuleMax variable is under a
Kconfig named 'EFI_HAVE_CAPSULE_UPDATE. Git history only shows a
single occurrence of that. The IS_ENABLED should be checking for
EFI_HAVE_CAPSULE_SUPPORT
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
"Unable to find TPMv2 device" doesn't explain much with regards to the
error origin. Update it to match what we have in the RNG protocol
installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently file ubootefi.var is only created if the user sets a non-volatile
EFI variable. If the file is missing, a warning is written.
With the change PlatformLang is always persisted. So the file will exist on
second boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Before clearing the screen, ensure that no previous output of firmware
or UEFI programs will be overwritten on serial devices or other
streaming consoles. This helps generating complete boot logs.
Tested regarding multi-output against qemu-x86_defconfig. Still, there
were remaining concerns about side effects, so this is provided as an
opt-in feature.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ensures a consistent background color of the whole screen for succeeding
outputs as both demanded by the spec and implemented in EDK2 as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a man-page for the bdinfo command
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the blkcache command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the source command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
UEFI applications call file system functions to determine if a file exists.
The return codes are evaluated to show appropriate messages.
U-Boot's file system layer should not interfere with the output.
Rename file_fat_read_at() to fat_read_file() adjusting the parameter
sequence and names and eliminate the old wrapper function.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When comparing UUIDs for discovered services we only compare up to the
ptr size instead of the entire UUID
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
commit fe8a4ed011 ("tee: optee: discover services dependent on tee-supplicant")
is trying to automatically scan and add TAs that are presented on pseudo
bus from the secure world.
In order to be able to list and compare the scanned devices the available drivers
have to register themselves on the op-tee service list.
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since I do have a look on TEE patches regardless and Jens doesn't have
his own tree, add myself as a co-maintainer. I'll be carrying over the
TEE related patches from now on. While at it add the maintenance tree
for TPM
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If we fail to probe the optee-rng device, we print a wrong message
referring to the firmware tpm.
Fixes: 476a3d58df ("tee: optee: don't fail probe because of optee-rng")
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
- A few TI platform fixes, compression test cleanup and zstd update,
npcm7xx update, add "part type" subcommand, VBE bugfix on some
platforms, cleanup EVENT related Kconfig option logic (and fix some
platforms), other minor cleanups.
In commit 4963f63fe6 ("image: Use gd->ram_base/_size in
env_get_bootm_size()") the size of the available memory for U-Boot to
use when relocating images, and not otherwise constrained, was changed
to include all known memory banks. In the case of this platform however,
all of the memory known to U-Boot is not also part of the Linux kernel
"lowmem" and so we must use CFG_SYS_BOOTMAPSZ to limit where we relocate
images to. We set a conservative limit of 256MB here to mirror the
previous behavior.
Signed-off-by: Joost van Zwieten <joost@diskos.nl>
[trini: Reword the commit messsage]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the sysreset based poweroff command. It invokes PSCI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This device is created when there are no bootmeths defined in the device
tree. But it cannot be probed without a device tree node.
For now, ignore a probe failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Karsten Merker <merker@debian.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: a56f663f07 ("vbe: Add info about the VBE device to the fwupd node")
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Karsten Merker <merker@debian.org>
Update the zstd implementation to match Linux zstd 1.5.2 from commit
2aa14b1ab2.
This was motivated by running into decompression corruption issues when
trying to uncompress files compressed with newer versions of zstd. zstd
users also claim significantly improved decompression times with newer
zstd versions which is a side benefit.
Original zstd code was copied from Linux commit 2aa14b1ab2 which is a
custom-built implementation based on zstd 1.3.1. Linux switched to an
implementation that is a copy of the upstream zstd code in Linux commit
e0c1b49f5b, this results in a large code diff. However this should make
future updates easier along with other benefits[1].
This commit is a straight mirror of the Linux zstd code, except to:
- update a few #include that do not translate cleanly
- linux/swab.h -> asm/byteorder.h
- linux/limits.h -> linux/kernel.h
- linux/module.h -> linux/compat.h
- remove assert() from debug.h so it doesn't conflict with u-boot's
assert()
- strip out the compressor code as was done in the previous u-boot zstd
- update existing zstd users to the new Linux zstd API
- change the #define for MEM_STATIC to use INLINE_KEYWORD for codesize
- add a new KConfig option that sets zstd build options to minify code
based on zstd's ZSTD_LIB_MINIFY[2].
These changes were tested by booting a zstd 1.5.2 compressed kernel inside a
FIT. And the squashfs changes by loading a file from zstd compressed squashfs
with sqfsload. buildman was used to compile test other boards and check for
binary bloat, as follows:
> $ buildman -b zstd2 --boards dh_imx6,m53menlo,mvebu_espressobin-88f3720,sandbox,sandbox64,stm32mp15_dhcom_basic,stm32mp15_dhcor_basic,turris_mox,turris_omnia -sS
> Summary of 6 commits for 9 boards (8 threads, 1 job per thread)
> 01: Merge branch '2023-01-10-platform-updates'
> arm: w+ m53menlo dh_imx6
> 02: lib: zstd: update to latest Linux zstd 1.5.2
> aarch64: (for 2/2 boards) all -3186.0 rodata +920.0 text -4106.0
> arm: (for 5/5 boards) all +1254.4 rodata +940.0 text +314.4
> sandbox: (for 2/2 boards) all -4452.0 data -16.0 rodata +640.0 text -5076.0
[1] e0c1b49f5b
[2] f302ad8811/lib/libzstd.mk (L31)
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
[trini: Set ret to -EINVAL for the error of "failed to detect
compressed" to fix warning, drop ZSTD_SRCSIZEHINT_MAX for non-Linux host
tool builds]
Signed-off-by: Tom Rini <trini@konsulko.com>
This makes it possible to run the patman test suite simply by invoking
'pytest' from the patman sub-directory:
$ cd tools/patman
$ pytest
Otherwise, the top level .checkpatch.conf would be ignored and
multiple test_checkpatch.py tests would fail.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
