ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
esbc_validate command will not be executed if “load” command for its
header fails and will further execute the source command for bootscript,
without its validation and boot process continues.
To halt the boot process in case secure boot header is not loaded
successfully, esbc_validate command is invoked separately after “load”
command. The secure boot validation of the bootscript header will fail
(if header is not loaded) and halts the boot process, which prevent source
command from execution.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Distinguish the ecc val by chassis version and move the ecc addr to dts.
Add ls1028a soc support.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the infrastructure for Layerscape SoCs PCIe Gen4 controller
to update device tree nodes to convey SMMU stream IDs in the
device tree.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add PCIe Gen4 driver for the NXP Layerscape SoCs. This PCIe
controller is based on the Mobiveil IP, which is compatible
with the PCI Express™ Base Specification, Revision 4.0.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bao Xiaowei <Xiaowei.Bao@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LS2080A has 8GB region for each PCIe controller, while the
other platforms have 32GB.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Update mtd-id for QSPI nor due to change introduced in mtd/spi in
linux 5.0. commit 84d043185dbe
("spi: Add a driver for the Freescale/NXP QuadSPI controller")
This modification is only for linux kernel version >= 5.0. To use
bootargs for kernel < 5.0, use the following bootargs
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0
earlycon=uart8250,mmio,0x21c0500
mtdparts=1550000.quadspi:2m(uboot),14m(free)"
CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.quadspi:2m(uboot),14m(free)"
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
It was returning an int, which doesn't work if the u32 it is reading,
or the default value, will overflow a signed int.
While it could be made to work, when using a C standard/compiler where
casting negative signed values to unsigned has a defined behavior,
combined with careful casting, it seems obvious one is meant to use
ofnode_read_s32_default() with signed values.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
The 'done' files created by buildman may end up being empty if buildman
runs out of disk space while writing them. At present buildman dies with
an exception when using -s to check the build status. Fix this.
Seriesl-cc: trini
Signed-off-by: Simon Glass <sjg@chromium.org>
Add ofnode_get_addr_size_index function to fetch the address
and size of the reg space based on index.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using fdt_fixup_mtdparts() offset and length cell sizes
are limited to 4 bytes (1 cell). However if the mtd device is
bigger then 4GiB, then #address-cells and #size-cells are
8 bytes (2 cells) [1].
This patch read #size-cells and uses either fdt32_t or
fdt64_t cell size. The default is fdt32_t.
[1] Documentation/devicetree/bindings/mtd/partition.txt
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot already defines the {upper,lower}_32_bits() macros that have the
same purpose. Use the existing macros instead of defining new APIs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some libraries build by U-Boot may include stdint.h. This is not used by
U-Boot itself and causes conflicts with the types defined in
linux/types.h. To work around this, add an empty file with this name so
that it will be used in preference to the compiler version.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is necessary to read the keyboard in early phases of
U-Boot. The cros_ec keyboard is kept in the misc directory. Update the
config to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.
To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.
The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Clean up the whitespaces in macros, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Pull DRAM layout configuration code into rcar-common.c instead of
having it in multiple copies across board files. This poses no
change for Salvator-X/XS, ULCB and Ebisu boards, however it adds
a bit of extra code for Draak and Eagle boards, which now gain
the capability of being passed in the DRAM layout by the ATF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add driver for the Renesas RCar PCIe controller present on Gen3 SoCs.
The PCIe on Gen3 is used both to connect external PCIe peripherals.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Add a U-Boot specific dts file, which encapsulates the needed
modifications to the Gazerbeam Linux device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The single channel detection in the gazerbeam board driver was not
implemented correctly.
Fix the detection.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Replace the boolean parameter of io_check_status that controls whether
the status is printed or not with a documenting enum.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
More recent versions of IHS FPGAs feature a different memory layout.
Add a Kconfig option to differentiate between the legacy layout, and the
new layout (which is used on the upcoming "Gazerbeam" and later boards).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Future gdsys boards will switch from the legacy drivers in board/gdsys/common
to DM-based drivers.
Define a Kconfig option that disables the legacy drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The "manual" RAM configuration should not be used if the DM RAM driver
is active, hence, disable the code if the CONFIG_MPC83XX_SDRAM config
variable is defined.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Move CONFIG_SYS_FPGA0_BASE, CONFIG_SYS_FPGA0_SIZE, CONFIG_SYS_FPGA1_BASE, and
CONFIG_SYS_FPGA1_SIZE to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since the gpio output status on MPC8xxx cannot be read back, it has to
be buffered locally.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
