Commit graph

4210 commits

Author SHA1 Message Date
Siarhei Siamashka
19e99fb4ff sunxi: Support booting from SPI flash
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:

    https://linux-sunxi.org/Bootable_SPI_flash

This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.

While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.

Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)

Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:

   sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin

The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 08:34:34 +02:00
Simon Glass
7d23b9cf2b dm: spl: Bind in all devices in SPL with of-platdata
When CONFIG_OF_PLATDATA is enabled, we cannot use the u-boot,dm-pre-reloc
device tree property since the device tree is not available. However,
dt-platdata.c only includes devices which would have been present in the
device tree, and we can assume that all such devices are needed for SPL.
If they were not needed, they would have been omitted to save space.

So in this case, bind all devices regardless of the u-boot,dm-pre-reloc
setting. This avoids needing to add a DM_FLAG_PRE_RELOC to every driver,
thus affecting U-Boot proper also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Simon Glass
d223e0a822 dm: spl: Don't set up device tree with of-platdata
When this feature is enabled, we should not access the device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Simon Glass
12c550d4fb spl: Drop include of i2c.h
This file does not appear to use I2C, so drop this include.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Anatolij Gustschin
ba169d981f board_f: prevent misleading "Watchdog enabled" output
Output the "Watchdog enabled" message only if hw_watchdog_init()
call really happened.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2016-07-14 18:33:09 -04:00
Anatolij Gustschin
46d7a3b3d3 board_f: init designware watchdog if CONFIG_DESIGNWARE_WATCHDOG=y
The designware watchdog init is skipped even if CONFIG_DESIGNWARE_WATCHDOG
is enabled. Fix it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2016-07-14 18:33:08 -04:00
Hector Palacios
19e8649e59 bootm: fixup silent Linux out of BOOTM_STATE_LOADOS state
The function fixup_silent_linux() is called in status BOOTM_STATE_LOADOS
to silence Linux if variable 'silent' is set.
Currently only the 'bootm' command state machine contains
BOOTM_STATE_LOADOS, but others like 'booti' or 'bootz' commands do not.
This means silent Linux does not work with these commands.

This patch moves the fixup_silent_linux() call out of the
BOOTM_STATE_LOADOS state and into BOOTM_STATE_OS_PREP, to silence Linux
independently of the used command (booti, bootm or bootz).

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
2016-07-14 18:22:44 -04:00
Simon Glass
b9c771b04c sandbox: Don't exit when bootm completes
At present sandbox exits when the 'bootm' command completes, since it is not
actually able to run the OS that is loaded. Normally 'bootm' failure is
considered a fatal error in U-Boot.

However this is annoying for tests, which may want to examine the state
after a test is complete. In any case there is a 'reset' command which can
be used to exit, if required.

Change the behaviour to return normally from the 'bootm' command on sandbox.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Teddy Reed <teddy.reed@gmail.com>
2016-07-14 18:22:32 -04:00
Simon Glass
1426220b0e image: Add functions to obtain category information
Add generic functions which can look up information about a category:

- the number of items in the category
- the category description
- an item long time
- an item short time

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:30 -04:00
Simon Glass
30495bff35 image: Add a name for invalid types
At present the name is NULL, which prevents qsort() fromp being used. Use
the name "invalid" instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:29 -04:00
Simon Glass
56d7ab7476 image: Create a table of information for each category
Add a table that contains the category name, the number of items in each
category and a pointer to the table of items. This will allow us to use
generic code to deal with the categories.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:29 -04:00
Daniel Allred
da74d1f341 spl: fit: add support for post-processing of images
The next stage boot loader image and the selected FDT can be post-
processed by board/platform/device-specific code, which can include
modifying the size and altering the starting source address before
copying these binary blobs to their final destination. This might be
desired to do things like strip headers or footers attached to the
images before they were packaged into the FIT, or to perform operations
such as decryption or authentication. Introduce new configuration
option CONFIG_SPL_FIT_IMAGE_POST_PROCESS to allow controlling this
feature. If enabled, a platform-specific post-process function must
be provided.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-14 18:22:21 -04:00
Tom Rini
bff97dde8c Merge branch 'master' of git://git.denx.de/u-boot-spi 2016-07-11 18:50:29 -04:00
Xu Ziyuan
ec3cde1e83 common: block: fix compiler error with CONFIG_FASTBOOT_FLASH_MMC_DEV
This fixes the following compiler error:

common/fb_mmc.c: In function ‘fb_mmc_erase’:
common/fb_mmc.c:209:17: error: ‘struct blk_desc’ has no member named
‘block_erase’

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-11 14:06:44 -06:00
Simon Glass
87bce4e5c0 dm: spl: mmc: Support CONFIG_BLK in SPL MMC
Update the method of accessing the block device so that it works with
CONFIG_BLK enabled.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-11 14:06:44 -06:00
Vignesh R
96907c0fe5 dm: spi: Read default speed and mode values from DT
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:34 +05:30
Masahiro Yamada
4632739202 autoboot: move bootdelay >= 0 check to abortboot()
Move the bootdelay >= 0 check to the caller, which simplifies
the callees.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01 17:42:56 -04:00
Masahiro Yamada
09b9d9e55f autoboot: move CONFIG_SILENT_CONSOLE handling
Factor out the same code from the callees to the caller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01 17:42:56 -04:00
Masahiro Yamada
d8da8298ad autoboot: rename abortboot_{keyed, normal} to __abortboot
Because abortboot_keyed() and abortboot_normal() are not compiled
at the same time, we can rename both of them to __abortboot().
This allows to drop #ifdef from the caller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01 17:42:55 -04:00
Masahiro Yamada
2fbb8462b0 autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECK
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.

To sum up, the autoboot behaves as follows:

 [1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    autoboot with no delay, with no check for abort

 [3] CONFIG_BOOTDELAY=-1
    disable autoboot

 [4] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK.  We can control all the
cases only by CONFIG_BOOTDELAY, like this:

 [1] CONFIG_BOOTDELAY=0
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=-1
    disable autoboot

 [3] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

This commit converts the logic as follow:
  CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    --> CONFIG_BOOTDELAY=-2

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2016-07-01 17:42:55 -04:00
Masahiro Yamada
9060970f4d doc: bootdelay: drop explanation about CONFIG_BOOTDELAY from README
The same information now exists in common/Kconfig.  Do not duplicate
documentation from the point of view of maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01 17:42:54 -04:00
Peng Fan
faaef73f7e common: add new boot media kconfig entry
Add CONFIG_{SD|NAND|ONENAND|SPI|QSPI|SATA}_BOOT kconfig entries.

SoCs supports loading U-Boot from different medias to DRAM, such as
i.MX6/7 supports loading U-Boot to DRAM from sd/emmc/nand/qspi/spi/sata
and etc. For i.MX, imximage will generate different IVT headers according
to boot medias.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
2016-06-27 22:35:25 -04:00
Peng Fan
d14739ffe1 Kconfig: make NOR_BOOT a common option
Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-27 22:32:07 -04:00
Steve Rae
0abd63b26d fastboot: sparse: improve CHUNK_TYPE_FILL write performance
- increase the size of the fill buffer
- testing has shown a 10x improvement when the sparse image
  has large CHUNK_TYPE_FILL chunks

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27 16:37:39 -04:00
Steve Rae
2c72404687 fastboot: sparse: implement reserve()
In order to process the CHUNK_TYPE_DONT_CARE properly, there is
a requirement to be able to 'reserve' a specified number of blocks
in the storage media. Because of the special handling of "bad blocks"
in NAND devices, this is implemented in a storage abstraction function.

Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-06-27 16:37:39 -04:00
Steve Rae
9bc34799c8 fastboot: sparse: resync common/image-sparse.c (part 2)
- update fastboot_okay() and fastboot_fail()

This file originally came from upstream code.

While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
  cmd_flash_mmc_sparse_img()
in the file
  aboot.c
from
  https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27 16:37:38 -04:00
Steve Rae
cc0f08cd34 fastboot: sparse: resync common/image-sparse.c (part 1)
This file originally came from upstream code.

While retaining the storage abstraction feature, this is the first
set of the changes required to resync with the
  cmd_flash_mmc_sparse_img()
in the file
  aboot.c
from
  https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27 16:37:36 -04:00
Steve Rae
64ece84854 fastboot: sparse: remove session-id logic
This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27 16:36:33 -04:00
Marek Vasut
2b1cdafa9f common: Pass the boot device into spl_boot_mode()
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.

The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Andrej Rosano
bd62e2419b common: Fix support for environment file in EXT4
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
2016-06-24 17:24:35 -04:00
Masahiro Yamada
f1f9d4fac5 hush: complete renaming CONFIG_SYS_HUSH_PARSER to CONFIG_HUSH_PARSER
There is no more define of CONFIG_SYS_HUSH_PARSER.  Rename some
remaining references and drop the backward compatible Kconfig entry.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-24 17:24:34 -04:00
Michael Trimarchi
4f1318b29c common: image: minimal android image iminfo support
We already support iminfo for other images. The idea
of this patch is start to have a minimal support for
android image format. We still need to print id[] array

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-24 17:23:07 -04:00
Masahiro Yamada
41598c8251 autoboot: add CONFIG_AUTOBOOT to allow to not compile autoboot.c
Since commit bb597c0eeb ("common: bootdelay: move CONFIG_BOOTDELAY
into a Kconfig option"), CONFIG_BOOTDELAY is defined for all boards.

Prior to that commit, it was allowed to unset CONFIG_BOOTDELAY to
not compile common/autoboot.c, as described in common/Makefile:

  # This option is not just y/n - it can have a numeric value
  ifdef CONFIG_BOOTDELAY
  obj-y += autoboot.o
  endif

It was a bit odd to enable/disable code with an integer type option,
but it was how this option worked before that commit, and several
boards actually unset it to opt out of the autoboot feature.

This commit adds a new bool option, CONFIG_AUTOBOOT, and makes
CONFIG_BOOTDELAY depend on it.

I chose "default y" for this option because most boards use the
autoboot.  I added "# CONFIG_AUTOBOOT is not set" for the boards that
had not set CONFIG_BOOTDELAY prior to the bad commit.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-20 05:19:09 -04:00
Tom Rini
2313d48445 Merge git://git.denx.de/u-boot-nand-flash 2016-06-20 05:15:52 -04:00
Sergey Kubushyn
61717571f2 common: fb_nand: won't compile
Somehow this got overlooked when getting rid of nand_info.

Small patch, won't affect anything else, no reason to wait for the
next cycle.

Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
2016-06-19 19:15:31 -05:00
Boris Brezillon
80ef700f8d spl: nand: support redundant u-boot image
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.

Add an extra Kconfig option to specify the offset of the redundant u-boot
image.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-19 19:11:57 -05:00
Petr Kulhavy
9ab165d8b0 SPL ext: cosmetic: correct error message in spl_load_image_ext()
Correct the error message in spl_load_image_ext() when image parsing
fails. Instead of "ext4fs_read failed" print "failed to parse image
header".

Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
CC: Tom Rini <trini@konsulko.com>
2016-06-19 09:57:48 -04:00
Petr Kulhavy
58c95d5356 SPL: ext: remove redundant ifdef statement
Remove redundant #if defined(CONFIG_SPL_OS_BOOT) statement around
getenv() calls in spl_load_image_ext_os().

The whole function is surrounded by #ifdef CONFIG_SPL_OS_BOOT.

No functional change.

Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
Acked-by:  Guillaume GARDET <guillaume.gardet@free.fr>
2016-06-17 09:51:00 -04:00
Andreas Dannenberg
e17adbb350 common: image-fit: Cleanup spelling mistakes
The comments in the source file are riddled with spelling mistakes. Be
a good citizen and take a stab at cleaning up some of the more obvious
ones.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-17 09:50:59 -04:00
Tom Rini
5e4e87418e common/Kconfig: Change the default BOOTDELAY to 2
The value of 0 is fairly uncommon while 2 is one of the more common ones
so switch.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-17 09:33:45 -04:00
Tom Rini
232d77e723 Merge branch 'master' of git://git.denx.de/u-boot-ubi 2016-06-17 09:33:06 -04:00
Eran Matityahu
1cb075c6c6 splash_source: add support for ubifs formatted nand
Add support for loading splash image from NAND Flash formatted with a (UBI) filesystem.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2016-06-14 05:33:02 +02:00
Tom Rini
f4abfed1de Merge branch 'master' of git://git.denx.de/u-boot-ubi 2016-06-13 08:51:21 -04:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Marcin Niestroj
c1f51e0f3e common: env_ubi: Clear environment buffer before reading
In case we have restarted u-boot there is a chance that environment
buffer contains old environment (from the previous boot). If UBI volume
is zero size, ubi_volume_read() doesn't modify the buffer and exits
successfully.

We need to clear buffer manually before reading it from UBI, so the
invalid CRC will cause setting default environment in case that the UBI
volume is zero size.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-06-13 06:41:20 +02:00
Simon Glass
b4d956f6bc bootm: Align cache flush end address correctly
Flushing part of the cache should be done on cache boundaries. Trying to
flush part of a cache line is not supported and the request may be ignored
or print warnings.

Adjust the bootm code to align the end address to prevent this problem.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Teddy Reed
51c14cd128 verified-boot: Minimal support for booting U-Boot proper from SPL
This allows a board to configure verified boot within the SPL using
a FIT or FIT with external data. It also allows the SPL to perform
signature verification without needing relocation.

The board configuration will need to add the following feature defines:
CONFIG_SPL_CRYPTO_SUPPORT
CONFIG_SPL_HASH_SUPPORT
CONFIG_SPL_SHA256

In this example, SHA256 is the only selected hashing algorithm.

And the following booleans:
CONFIG_SPL=y
CONFIG_SPL_DM=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_SPL_OF_LIBFDT=y
CONFIG_SPL_FIT_SIGNATURE=y

Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Sumit Garg <sumit.garg@nxp.com>
2016-06-12 13:14:58 -04:00
Heiko Schocher
496c5483e9 bootstage: call show_boot_progress also in SPL
show_boot_progress() is now called from SPL also.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:08 -04:00
Heiko Schocher
bb597c0eeb common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-06-09 13:53:05 -04:00
Ed Swarthout
69c125fe7b dm: scsi: if_typename should be scsi
Fixes:

=> ext2ls scsi 0:1
** Bad device scsi 0:1 **

for boards which use the scsi legacy driver (such as ls1043ardb).

Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-06 13:39:12 -04:00
Tom Rini
ffd859979e Merge branch 'master' of git://git.denx.de/u-boot-usb
Modified:
	configs/ls1012afrdm_qspi_defconfig
	configs/ls1012aqds_qspi_defconfig
	configs/ls1012ardb_qspi_defconfig
	include/configs/ls1012afrdm.h
	include/configs/ls1012aqds.h
	include/configs/ls1012ardb.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-06 13:37:56 -04:00
Tom Rini
1cb9cb3ec0 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-06-06 07:16:39 -04:00
Michal Simek
340b0e3bb6 env: Setup GD_FLG_ENV_DEFAULT flag when default environment are used
Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
2016-06-06 11:23:27 +02:00
Andreas Dannenberg
8aa57a95a2 spl: fit: Fix non-matching DT names console output
When no DTB can be matched successfully to the board that's being used
a list of available FIT-embedded DTBs will be output to the console for
diagnostic purposes. But rather than the contents of the "description"
FDT property a non-existent property was accessed and as a result "NULL"
was output instead of the actual name(s) of the DTB(s). Fix this issue
by using the correct property which is also the exact same property
that's used earlier during the actual board matching process.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2016-06-04 08:50:17 -04:00
Scott Wood
b616d9b0a7 nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Scott Wood
151c06ec61 mtd: nand: Remove nand_info_t typedef
This typedef serves no purpose other than causing confusion with
struct nand_chip.

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Masahiro Yamada
0a8cc1a3a4 usb: move CONFIG_USB_XHCI to Kconfig with renaming
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.

As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.

Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-04 00:43:53 +02:00
Tom Rini
edb697cfcc Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2016-06-02 21:42:23 -04:00
Marek Vasut
94b9e22e50 spl: Allow settings malloc_f base address
Allow configuring the begining of the malloc_f area in SPL.
This patch uses the same CONFIG_MALLOC_F_ADDR established by
the sandbox.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
2016-06-02 21:21:42 -04:00
Marek Vasut
1254667689 spl: Remove bogus GD_FLG_SPL_INIT check
Remove the check for GD_FLG_SPL_INIT in spl_relocate_stack_gd().
The check will always fail. This is because spl_relocate_stack_gd()
is called from ARM's crt0.S and it is called before board_init_r().
The board_init_r() calls spl_init(), which sets the GD_FLG_SPL_INIT
flag.

Note that reserving the malloc area in RAM is not a problem even
if the GD_FLG_SPL_INIT flag is not set.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
2016-06-01 22:44:14 +02:00
Lokesh Vutla
8b528709c5 spl: fit: Fix load address of fit header
When loading fit header, it should be loaded to a previous address
aligned to ARCH_DMA_MINALIGN and not 8. Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-01 07:12:38 -04:00
Tom Rini
e4a94ce4ac Merge git://git.denx.de/u-boot-dm
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	lib/efi_loader/efi_disk.c

Modified:
	configs/odroid-c2_defconfig
2016-05-27 20:34:12 -04:00
Lokesh Vutla
fa715193c0 spl: Add an option to load a FIT containing U-Boot from UART
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from UART.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:42 -04:00
Lokesh Vutla
cfe32a4be2 spl: fit: Do not print selected dtb during fit load
No prints should be allowed during UART load.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:42 -04:00
Lokesh Vutla
8bd8877279 spl: Support loading a FIT from NAND
Detect a FIT when loading from NAND and handle it using the
new FIT SPL support.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make sure we continue to use (void *)(unsigned long) for
load_addr].
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:14 -04:00
Lokesh Vutla
97ca364faf spl: Support loading a FIT from FAT FS
Detect a FIT when loading from a FAT File system and handle it using the
new FIT SPL support.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:41:40 -04:00
Lokesh Vutla
eafd5410af spl: Allow to load a FIT containing U-Boot from FS
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from a File system. Making sure that all the reads and writes
are aligned to their respective needs.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make this still apply with Michal's alignment change for 'fit']
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:39 -04:00
Lokesh Vutla
4d9d34a7f2 spl: fit: Fix the number of bytes read when reading fdt from fit
sectors field is not being updated when reading fdt from fit image. Because of
this size_of(u-boot.bin) is being read when reading fdt. Fixing it by updating
the sectors field properly.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:41:39 -04:00
Simon Glass
9be2e790eb Drop use of CONFIG_SYS_GENERIC_BOARD in U-Boot
This option is always enabled and is about to be removed. Drop references
to it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-05-27 15:39:54 -04:00
Simon Glass
b0b359536e board_f: Don't require CONFIG_SYS_MONITOR_BASE
Allow this to be unset, such that gd->mon_len is invalid. This seems to be
what the sh architecture does.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 15:39:51 -04:00
Lukasz Majewski
851bda8148 cosmetic: debug: Replace #ifdef DEBUG with debug() macro
Replace #ifdef DEBUG with dedicated debug() macro.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
2016-05-27 15:39:48 -04:00
Simon Glass
ef5609c33f dm: mmc: spl: Add support for CONFIG_BLK
Allow driver model to be used for block devices in SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:09 -06:00
Simon Glass
5461acba44 dm: env: mmc: Convert env_mmc to support CONFIG_BLK
Update the MMC environment code so that it works with driver-model enabled
for block devices.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 10:23:08 -06:00
Michal Simek
90a7417602 SPL: FIT: Align loading address for header
If bl_len is not aligned it can caused a problem because another code
expects that start is aligned.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 09:56:20 -04:00
Paul Burton
49717b18be fdt: Document the rest of struct of_bus
Provide some documentation for the fields of struct of_bus, for
consistency with that provided for the new match field.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-25 23:13:38 +02:00
Paul Burton
0a222d53d8 fdt: Support for ISA busses
Support ISA busses in much the same way as Linux does. This allows for
ISA bus addresses to be translated, and only if CONFIG_OF_ISA_BUS is
selected in order to avoid including the code in builds which won't need
it.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-25 23:13:09 +02:00
Michal Simek
62afc60188 image: Add boot_get_fpga() to load fpga with bootm
Add function boot_get_fpga() which find and load bitstream to
programmable logic if fpga entry is present.
Function is supported on Xilinx devices for full and partial bitstreams
in BIN and BIT format.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove additional blankline in image.h
2016-05-24 13:17:59 +02:00
Michal Simek
ed0cea7c52 mkimage: Report information about fpga
Add FIT_FPGA_PROP that user can identify an optional
entry for fpga.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24 11:15:02 +02:00
Michal Simek
d9b58b3031 tools: zynqmpimage: Add Xilinx ZynqMP boot header generation
Add support for the zynqmpimage to mkimage.
Only basic functionality is supported without encryption and register
initialization with one partition which is filled by U-Boot SPL.
For more detail information look at Xilinx ZynqMP TRM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24 11:15:01 +02:00
Michal Simek
8d16e1d593 SPL: FIT: Enable SPL_FIT_LOAD in RAM based boot mode
Support loading FIT in SPL for RAM bootmode.
CONFIG_SPL_LOAD_FIT_ADRESS points to address where FIT image is stored
in memory.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-24 11:15:01 +02:00
Michal Simek
3a3b914789 spl: Introduce new function spl_board_prepare_for_boot
Call this function before passing control from SPL.
For fpga case it is necessary to enable for example level shifters
when bitstream is programmed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24 11:15:01 +02:00
Tom Rini
d550e82e4e SPL: fat: Fix spl_parse_image_header() return value handling
The spl_parse_image_header() can return 0 and it is not an error.
Only treat non-zero return value as an error.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-23 11:51:13 -04:00
Michal Simek
5adfa26579 spl: fit: Print error message when FDT is not present
When FDT is not present in the image user doesn't get any error what's
wrong. Print error message if LIBCOMMON_SUPPORT is enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Seris-cc: uboot
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 11:50:20 -04:00
Simon Glass
8df81e17f8 image-fit: Don't display an error in fit_set_timestamp()
This function returns an error code and its caller may be able to fix the
error. For example fit_handle_file() expands the device tree to fit if there
is a lack of space.

In this case the caller does not want an error displayed. It is confusing,
since it suggests that something is wrong, when it fact everything is fine.
Drop the error.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-23 11:50:18 -04:00
Stephen Warren
034eda867f malloc: improve memalign fragmentation fix
Commit 4f144a4164 "malloc: work around some memalign fragmentation
issues" enhanced memalign() so that it can succeed in more cases where
heap fragmentation is present. However, it did not solve as many cases
as it could. This patch enhances the code to cover more cases.

The alignment code works by allocating more space than the user requests,
then adjusting the returned pointer to achieve alignment. In general, one
must allocate "alignment" bytes more than the user requested in order to
guarantee that alignment is possible. This is what the original code does.
The previous enhancement attempted a second allocation if the padded
allocation failed, and succeeded if that allocation just happened to be
aligned; a fluke that happened often in practice. There are still cases
where this could fail, yet where it is still possible to honor the user's
allocation request. In particular, if the heap contains a free region that
is large enough for the user's request, and for leading padding to ensure
alignment, but has no or little space for any trailing padding. In this
case, we can make a third(!) allocation attempt after calculating exactly
the size of the leading padding required to achieve alignment, which is
the minimal over-allocation needed for the overall memalign() operation to
succeed if the third and second allocations end up at the same location.

This patch isn't checkpatch-clean, since it conforms to the existing
coding style in dlmalloc.c, which is different to the rest of U-Boot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-23 11:50:17 -04:00
Nikita Kiryanov
aa9e604410 cmd: eeprom: add support for layout aware commands
Introduce the (optional) eeprom print and eeprom update commands.

These commands are eeprom layout aware:
* The eeprom print command prints the contents of the eeprom in a human
  readable way (eeprom layout fields, and data formatted to be fit for human
  consumption).
* The eeprom update command allows user to update eeprom fields by specifying
  the field name, and providing the new data in a human readable format (same
  format as displayed by the eeprom print command).
* Both commands can either auto detect the layout, or be told which layout to
  use.

New CONFIG options:
CONFIG_CMD_EEPROM_LAYOUT - enables commands.
CONFIG_EEPROM_LAYOUT_HELP_STRING - tells user what layout names are supported

Feature API:
__weak int parse_layout_version(char *str)
	- override to provide your own layout name parsing
__weak void __eeprom_layout_assign(struct eeprom_layout *layout, int layout_version);
	- override to setup the layout metadata based on the version
__weak int eeprom_layout_detect(unsigned char *data)
	- override to provide your own algorithm for detecting layout version
eeprom_field.c
	- contains various printing and updating functions for common types of
	  eeprom fields. Can be used for defining custom layouts.

Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2016-05-20 17:02:07 -04:00
Tom Rini
4b6e1fda10 Merge git://git.denx.de/u-boot-dm 2016-05-17 13:58:27 -04:00
Simon Glass
69f45cd53b dm: mmc: Use the new select_hwpart() API
Avoid calling directly into the MMC code - use the new API call instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
9107c973d3 dm: blk: Add a easier way to create a named block device
Add a function that automatically builds the device name given the parent
and a supplied string. Most callers will want to do this, so putting this
functionality in one place makes more sense.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
f5a14af9c4 dm: sata: Add support for driver-model block devices
Add driver-model block-device support to the SATA implementation. This is
just a dummy implementation for now, since the SATA low-level API uses
numbered devices and that doesn't fit with driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
535556b2aa dm: scsi: Add support for driver-model block devices
Add driver-model block-device support to the SCSI implementation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
145df842b4 dm: ide: Add support for driver-model block devices
Add driver-model block-device support to the IDE implementation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
edd82ab354 dm: scsi: Drop the get_dev() function
This function is implemented by the legacy block functions now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
74001a2570 dm: ide: Drop the get_dev() function
This function is implemented by the legacy block functions now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
57ebf67bad dm: usb: Drop the get_dev() function
This function is implemented by the legacy block functions now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
d97dc8a0e6 dm: sata: Separate the non-command code into its own file
At present the SATA command code includes both the command-processing code
and the core SATA functions and data structures.

Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.

With this commit:
- All CONFIG option are referenced from the non-command code
- The concept of a 'current SATA device' is confined to the command code

This will make it easier to convert this code to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
e9be1ee75e dm: ide: Separate the non-command code into its own file
At present the IDE command code includes both the command-processing code
and the core IDE functions and data structures.

Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.

With this commit:
- Most CONFIG option are referenced from the non-command code
- The concept of a 'current IDE device' is confined to the command code

This will make it easier to convert this code to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
11f610edf0 dm: scsi: Separate the non-command code into its own file
At present the SCSI command code includes both the command-processing code
and the core SCSI functions and data structures.

Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly. This functions use the
new legacy block functions.

With this commit:
- There is no CONFIG option referenced from the command code
- The concept of a 'current SCSI device' is confined to the command code

This will make it easier to convert this code to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
c0543bf6be dm: usb: Add a legacy block interface for USB storage
Add a legacy block interface for USB storage.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
c649e3c91c dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSI
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Marek Vasut
e072751515 SPL: Add CONFIG_SPL_ABORT_ON_RAW_IMAGE
When defined, SPL will proceed to another boot method
if the image it has loaded does not have a signature.
This is useful if the subsequent boot methods are much
more complex.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2016-05-17 17:52:20 +02:00
Marek Vasut
7e0f22674a SPL: Let spl_parse_image_header() return value
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
2016-05-17 17:52:20 +02:00
Marek Vasut
d81db48d41 usb: hub: Don't continue on get_port_status failure
The code shouldn't continue probing the port if get_port_status() failed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
2016-05-06 20:06:56 +02:00
Marek Vasut
ef71290be9 usb: Assure Get Descriptor request is in separate microframe
The Kingston DT Ultimate USB 3.0 stick is sensitive to this first
Get Descriptor request and if the request is not in a separate
microframe, the stick refuses to operate. Add slight delay, which
is enough for one microframe to pass on any USB spec revision.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
2016-05-06 20:06:56 +02:00
Marek Vasut
f647bf0ba3 usb: Wait after sending Set Configuration request
Some devices, like the SanDisk Cruzer Pop need some time to process
the Set Configuration request, so wait a little until they are ready.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
2016-05-06 20:06:56 +02:00
Marek Vasut
2f1b4302e3 usb: Don't init pointer to zero, but NULL
The pointer should always be inited to NULL, not zero (0). These are
two different things and not necessarily equal.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
2016-05-06 18:35:06 +02:00
Lev Iserovich
a434fd1d28 fdt: fix setting MAC addresses for multiple interfaces
For multiple ethernet interfaces the FDT offset of '/aliases' will change as we
are adding MAC addresses to the FDT.
Therefore only the first interface ('ethernet0') will get properly updated in
the FDT, with the rest getting FDT errors when we try to set their MAC address.

Signed-off-by: Lev Iserovich <iserovil@deshawresearch.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-03 17:52:10 -05:00
Vagrant Cascadian
eae4b2b67b Fix spelling of "occurred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-02 18:37:09 -04:00
Robert P. J. Day
4eece2602b common/dlmalloc.c: Delete content that was moved to malloc.h
Remove several hundred lines of content surrounded by:

#if 0  /* Moved to malloc.h */
... moved stuff ...
#endif /* 0 */                 /* Moved to malloc.h */

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:10:36 -04:00
Fabio Estevam
5bbf409909 spl: spl_mmc: Disambiguate error message
The error message "spl: mmc block read error" may come from two
different functions, so we should better annotate the function name
where the error comes from to help debugging.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:10:36 -04:00
Peng Fan
125d193c4f common: env: support sata device
Introduce env support for sata device.
1. Implement write_env/read_env/env_relocate_spec/saveenv/sata_get_env_dev
2. If want to enable this feature, define CONFIG_ENV_IS_IN_SATA, and
   define CONFIG_SYS_SATA_ENV_DEV or implement your own sata_get_ev_dev.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stuart Longland <stuartl@vrt.com.au>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 12:29:14 -04:00
Steve Rae
e3793541b1 fastboot: sparse: remove unnecessary logging
remove logging of the 'skipped' blocks

Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-04-11 20:48:29 -04:00
Steve Rae
c7529dbad1 fastboot: sparse: fix block addressing for don't care chunk type
When 7bfc3b1 (sparse: Refactor chunk parsing function) was implemented,
it dropped 9981945 (aboot: fix block addressing for don't care chunk type).

This re-implements the required fix for the "don't care chunk type"...

Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-04-11 20:48:29 -04:00
Lokesh Vutla
811906aebc spl: mmc: raw: Try to load u-boot if Linux image is not found
If CONFIG_SPL_OS_BOOT is enabled and Linux image is not flashed at
RAW_MODE_KERNEL_SECTOR in MMC, spl still assumes that Linux is
available and tries to boot it and hangs. In order to avoid this,
adding a check to verify if parsed image header is of type IH_OS_LINUX.
If it fails then fall back to load u-boot image.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-04-11 20:48:27 -04:00
Guy Thouret
c00c29d8f7 env_eeprom invalidates gd->env_addr by setting it to an offset value
Patch to fix boot hang when using env on i2c eeprom caused by invalid gd->env_addr

Signed-off-by: Guy Thouret <guy.thouret@wems.co.uk>
Cc: Heiko Schocher <hs@denx.de>
2016-04-11 12:44:37 -04:00
Jeffy Chen
d3bafe32ca fastboot: sparse: fix sparse blocks calculation
It may overflow in sparse_block_size_to_storage, use uint64_t instead in
the calculation.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
2016-04-11 12:44:37 -04:00
Hans de Goede
9a80e71435 usb: kbd: Do not deregister usbkbd twice when using dm
The dm usb_kbd_remove function() will deregister the usb keyboard for
us on a "usb reset" / "usb stop" so there is no need to manually call
usb_kbd_deregister() in the dm case.

This commit removes usb_kbd_deregister() in the dm case fixing the
following "usb reset" errors:

usb_kbd_remove: warning, ret=-6
device_remove: Device 'usb_kbd' failed to remove, but children are gone

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-10 17:18:42 +02:00
Stefan Roese
30eae26b56 common: cli: Fix typo CONFIG_CMDINE -> CONFIG_CMDLINE
Patch f8bb6964 (Drop command-processing code when CONFIG_CMDLINE is
disabled) introduced a small typo. This patch fixes it and unbreaks
all boards again that don't have the Hush parser enabled.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2016-04-04 13:13:07 -04:00
Peng Fan
9a5d993e65 common: env_sf: Add exclamation mark
Add exclamation mark to the errmsg, when error and set_default_env.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Ravi Babu <ravibabu@ti.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:43 -04:00
Ahmed Samir Khalil
8122d2161e Common: SPL: spl_nand: Fixed debug correct NAND ECC type.
In case of #define DEBUG 1 (fordebugging SPL). A bug in
spl_nand_load_image() will be triggered, because it prints
using hw ecc regardless of soft ecc configurations and
initializations.

Signed-off-by: Ahmed Samir <engkhalil86@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:42 -04:00
Simon Glass
f8bb696435 Drop command-processing code when CONFIG_CMDLINE is disabled
Command parsing and processing code is not needed when the command line is
disabled. Remove this code in that case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:40 -04:00
Bin Meng
ce1a7d1564 debug_uart: Remove duplicated carriage return handling
Since commit b391d74 "debug_uart: output CR along with LF", the
handling in puts() is duplicated, not to mention that it should
output carriage return before line feed.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:26 -04:00
Alexander Merkle
dd8d8da3d7 Fix typo choosen in comments and printf logs
Minor change: chosen is written with one "o".
No code change here, only comment & printf.

Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-27 09:12:23 -04:00
Alexander Graf
f8f58fbb09 lcd: Fix compile warning in 64bit mode
When compiling the code for 64bit, the lcd code emits warnings because it
tries to cast pointers to 32bit values. Fix it by casting them to longs
instead, actually properly aligning with the function prototype.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-27 09:12:17 -04:00
Tom Rini
b5b84be8a7 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-03-23 18:35:11 -04:00
Hans de Goede
8f10b5c656 spl: Print from which mmc slot spl is trying to boot
On some sunxi boards (and presumably also non sunxi boards) u-boot can
be either loaded from a sdcard in a micro-sd slot, or from eMMC.

Print which MMC spl tries to boot from, to help debugging.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-23 22:04:13 +01:00
Masahiro Yamada
4976f48275 spl_mmc: allow to load raw image
The function spl_parse_image_header() falls back to a raw image
if the U-Boot header is missing and CONFIG_SPL_PANIC_ON_RAW_IMAGE
is undefined.  While, mmc_load_image_raw_sector() only accepts a
U-Boot legacy image or an FIT image, preventing us from loading a
raw image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-24 01:36:55 +09:00
Simon Glass
b94fc8518e usb: Correct return value in usb_stor_info()
This should return 0 on success, not 1. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:28 -04:00
Vagrant Cascadian
a6f70a3d14 Fix spelling of "transferred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:16 -04:00
Simon Glass
1872c67359 Allow command-line files to be dropped
These files do not need to be compiled when CONFIG_CMDLINE is disabled.
Update the Makefile to reflect this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:11 -04:00
Simon Glass
045e6f0d4f Panic when no command line processing can be performed
Normally board_run_command() will handle command processed. But if for some
reason it returns then we should panic to avoid further processing.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:10 -04:00
Stefan Roese
c998da0d67 usb: Change power-on / scanning timeout handling
This patch changes the USB port scanning procedure and timeout
handling in the following ways:

a)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total timeout for this
hub, which is 1 second + "hub->desc.bPwrOn2PwrGood * 2" is calculated
and will be used in the following per-port scanning loop as the timeout
to detect active USB devices on this hub.

b)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scannig
loop until the delay time is reached.

c)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list. This list is scanned until all ports are ready
by either a) reaching the connection timeout (calculated earlier), or
by b) detecting a USB device. This results in a faster USB scan time as
the recursive scanning of USB hubs connected to the hub that's currently
being scanned will start earlier.

One small functional change to the original code is, that ports with
overcurrent detection will now get rescanned multiple times
(PORT_OVERCURRENT_MAX_SCAN_COUNT).

Without this patch:
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 20.163 seconds

With this patch:
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 1.822 seconds

So ~18.3 seconds of USB scanning time reduction.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-20 18:00:45 +01:00
Stefan Roese
3ed9eb93c2 usb: Don't reset the USB hub a 2nd time
Debugging has shown, that all USB hubs are being reset twice while
USB scanning. This introduces additional delays and makes USB scanning
even more slow. Testing has shown that this 2nd USB hub reset doesn't
seem to be necessary.

This patch now removes this 2nd USB hub reset. Resulting in faster USB
scan time. Here the current numbers:

Without this patch:
=> time usb start
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 24.003 seconds

With this patch:
=> time usb start
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 20.392 seconds

So ~3.6 seconds of USB scanning time reduction.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
2016-03-20 18:00:45 +01:00
Stefan Roese
2ef117fe4f usb: Remove 200 ms delay in usb_hub_port_connect_change()
This patch removes 2 mdelay(200) calls from usb_hub_port_connect_change().
These delays don't seem to be necessary. At least not in my tests. Here
the number for a custom x86 Bay Trail board (not in mainline yet) with
a quite large and complex USB hub infrastructure.

Without this patch:
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 28.415 seconds

With this patch:
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found

time: 24.003 seconds

So ~4.5 seconds of USB scanning time reduction.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
2016-03-20 18:00:44 +01:00
Stefan Roese
f7f601002d usb: legacy_hub_port_reset(): Speedup hub reset handling
Start with a short USB hub reset delay of 20ms. This can be enough for
some configurations.

The 2nd delay at the end of the loop is completely removed. Since the
delay hasn't been long enough, a longer delay time of 200ms is assigned
and will be used in the next loop round.

This hub reset handling is also used in the v4.4 Linux USB driver,
hub_port_reset().

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
2016-03-20 18:00:44 +01:00
Przemyslaw Marczak
4428f3c87a Revert "fdt: fix address cell count checking in fdt_translate_address()"
This reverts commit 71105f50fe.

The reverted commit was applied for a temporary to unbreak
few Exynos boards on the release.

After the discussion about the change, this commit should be avoided.
Fixed device-tree for Exynos, allows reverting it without any issues.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2016-03-17 21:27:39 -06:00
Simon Glass
e4d6ab0c2c x86: Allow use of serial soon after relocation
At present on x86 machines with use cache-as-RAM, the memory goes away just
before board_init_r() is called. This means that serial drivers are
no-longer unavailable, until initr_dm() it called, etc.

Any attempt to use printf() within this period will cause a hang.

To fix this, mark the serial devices as 'unavailable' when it is no-longer
available. Bring it back when serial_initialize() is called. This means that
the debug UART will be used instead for this period.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:24 +08:00
Simon Glass
d74d6b444c dm: timer: Correct timer init ordering after relocation
Commit 1057e6c broke use of the timer with driver model. If the timer is used
before relocation, then it becomes broken after relocation. This prevents
some x86 boards from booting. Fix it.

Fixes: 1057e6c (timer: Set up the real timer after driver model is available)

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:24 +08:00
Simon Glass
9a01cca750 malloc_simple: Add a little more debugging
Output the pointer returned by each call to malloc(). This can be useful
when debugging memory problems.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:23 +08:00
Masahiro Yamada
70e6428d8c spl_nor: fix warning when compiled for 64bit target
Fix "warning: cast to pointer from integer of different size".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-15 21:30:20 -04:00
Alexander Graf
dea2174d9d efi_loader: Call fdt preparation functions
We have a nice framework around image fils to prepare a device tree
for OS execution. That one patches in missing device tree nodes and
fixes up the memory range bits.

We need to call that one from the EFI boot path too to get all those
nice fixups. This patch adds the call.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-15 21:30:14 -04:00
Alexander Graf
5d00995c36 efi_loader: Implement memory allocation and map
The EFI loader needs to maintain views of memory - general system memory
windows as well as used locations inside those and potential runtime service
MMIO windows.

To manage all of these, add a few helpers that maintain an internal
representation of the map the similar to how the EFI API later on reports
it to the application.

For allocations, the scheme is very simple. We basically allow allocations
to replace chunks of previously done maps, so that a new LOADER_DATA
allocation for example can remove a piece of the RAM map. When no specific
address is given, we just take the highest possible address in the lowest
RAM map that fits the allocation size.

Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15 21:30:10 -04:00
Alexander Graf
50149ea37a efi_loader: Add runtime services
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.

This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.

We could maybe in the future map U-boot environment variables to EFI variables
here.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15 18:03:10 -04:00
Tom Rini
88033d737d Merge git://git.denx.de/u-boot-dm 2016-03-14 19:21:44 -04:00
Stefan Roese
ecb57f69b2 lib/crc16.c: Rename cyg_crc16() to crc16_ccitt() and add crc start value
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.

To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:42 -04:00
York Sun
c1913cb789 common: image-fit: Fix load and entry addresses in FIT image
FIT image supports more than 32 bits in addresses by using #address-cell
field. Fixing 64-bit support by using this field.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:41 -04:00
York Sun
6004765d14 common: image-fit: Use a common function to get address
FIT image supports load address and entry address. Getting these
addresses can use a common function.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:40 -04:00
Simon Glass
96debd1f0b spl: Support loading a FIT from MMC
Detect a FIT when loading from MMC and handle it using the new FIT SPL
support.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:31 -04:00
Simon Glass
f1dcee59a2 spl: Add an option to load a FIT containing U-Boot
This provides a way to load a FIT containing U-Boot and a selection of device
tree files. The board can select the correct device tree by probing the
hardware. Then U-Boot is started with the selected device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:30 -04:00
Simon Glass
cef2e51489 image: Add functions to obtain short names
Sometimes it is useful to obtain the short name for an Operating System,
architecture or compression mechanism. Provide functions for this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:28 -04:00
Simon Glass
aa34fbc087 fdt: Allow libfdt to be used in SPL
Add an option to enable libfdt in SPL. This can be useful when decoding
FIT files in SPL.

We need to make sure this option is not enabled in SPL by this change.
Also this option needs to be enabled in host builds. Si add a new
IMAGE_USE_LIBFDT #define which can be used in files that are built on the
host but must also build for U-Boot and SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:26 -04:00
Simon Glass
73223f0e1b Kconfig: Move CONFIG_FIT and related options to Kconfig
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

   CONFIG_FIT
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_FIT_SIGNATURE
   CONFIG_FIT_BEST_MATCH
   CONFIG_FIT_VERBOSE
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:07 -04:00
Simon Glass
07b2b78ce4 dm: usb: Convert USB storage to use driver-model for block devs
Update this code to support CONFIG_BLK. Each USB storage device can have
one or more block devices as children, each one representing a LUN
(logical unit) of the USB device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
9807c3b78a dm: usb: Tidy up storage code ready for driver model conversion
Adjust a few things so that the addition of driver-models support involved
adding code rather than also changing it. This makes the patches easier to
review.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
c89e79d419 dm: usb: Avoid exceeding available array size for storage devices
The limit on storage devices is USB_MAX_STOR_DEV but we use one extra
element while probing to see if a device is a storage device. Avoid this,
since it causes memory corruption.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
2a981dc2c6 dm: block: Adjust device calls to go through helpers function
To ease conversion to driver model, add helper functions which deal with
calling each block device method. With driver model we can reimplement these
functions with the same arguments.

Use inline functions to avoid increasing code size on some boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
bcce53d048 dm: block: Rename device number member dev to devnum
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
3e8bd46950 dm: part: Rename some partition functions
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
e35929e4a1 dm: blk: Rename get_device_and_partition()
Rename this function to blk_get_device_part_str(). This is a better name
because it makes it clear that the function returns a block device and
parses a string.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
db1d9e78e6 dm: blk: Rename get_dev() to blk_get_dev()
The current name is too generic. Add a 'blk_' prefix to aid searching and
make its purpose clearer.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Simon Glass
4101f68792 dm: Drop the block_dev_desc_t typedef
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14 15:34:50 -06:00
Stuart Longland
fd1000b9c1 common: Add support for environment file in EXT4.
This is an enhancement that permits storing the environment file on an
EXT4 partition such as the root filesystem.  It is based on the existing
FAT environment file code.
2016-03-14 14:18:39 -04:00
Stephen Warren
deff6fb3a7 malloc: remove !gd handling
Following the previous patch, malloc() is never called before gd is set,
so we can remove the special-case check for this condition.

This reverts commit 854d2b9753 "dlmalloc: ensure gd is set for early
alloc".

Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-08 15:01:47 -05:00
Simon Glass
1057e6cfe1 timer: Set up the real timer after driver model is available
When using the early timer, we need to manually trigger setting up the
real timer. This will not happen automatically. Do this immediately after
starting driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-26 08:53:10 -07:00
Simon Glass
2e33e76165 Revert "image-fit: Fix signature checking"
This reverts commit 84ca65aa4b.

On signature verification failures fit_image_verify() should NOT exit with
error. Only keys marked 'required' can cause image verification failure.
This logic is already there and works correctly.

Add a comment to make this clear.

Fixes: 84ca65aa (image-fit: Fix signature checking)
Signed-off-by: Simon Glass <sjg@chromium.org>
2016-02-26 08:53:10 -07:00
Simon Glass
7a80de4641 image: Correct the OS location code to work on sandbox
A recent change broke the 'bootm' command on sandbox. The root cause is
using a pointer as an address. Conversion from pointer to address needs to
use map_to_sysmem() so that sandbox can do the right thing. The problem was
pre-existing but uncovered by a recent commit.

Fix this. Also move fit_get_end() to the C file to avoid needing to include
mapmem.h (and thus asm/io.h) everywhere.

Fixes: 1fec3c5d (common/image.c: Make boot_get_ramdisk() perform a check for Android images)

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-02-26 08:53:10 -07:00
Guillaume GARDET
86a0df7328 spl: if MMCSD_MODE_RAW fails, try MMCSD_MODE_FS
Since commit fd61d39970:
        spl: mmc: add break statements in spl_mmc_load_image()
RAW and FS boot modes are now exclusive again. So, if MMCSD_MODE_RAW fails, the
board hangs. This patch allows to try MMCSD_MODE_FS then.

It has been tested on a beaglebone black to boot on an EXT partition.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2016-02-19 09:31:37 -05:00
Lubomir Rintel
ed0f40a673 tools: fix env_flags build
$ make tools-all
  ...
  In file included from tools/env/env_flags.c:1:0:
  tools/env/../../common/env_flags.c: In function
    ‘env_flags_parse_varaccess_from_binflags’:
    tools/env/../../common/env_flags.c:156:18: warning: implicit declaration
    of function ‘ARRAY_SIZE’ [-Wimplicit-function-declaration]
      for (i = 0; i < ARRAY_SIZE(env_flags_varaccess_mask); i++)
                      ^
Seems like the other utilities just add a copy of ARRAY_SIZE since
there's nowhere to include it from (tools/imagetool.h,
tools/mxsimage.h). Let's do the same here.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2016-02-15 20:58:25 +00:00
Tom Rini
9ef2835f26 Merge branch 'master' of git://git.denx.de/u-boot-video 2016-02-11 18:18:15 -05:00
Simon Glass
a2931b30d2 dm: video: Add a temporary work-around for old stdout var
Boards with a saved environment may use 'lcd' in their stdout environment
variable, expecting that this will enable output to the LCD. When the board
moves to use driver model for video, this will no-longer work. Add a
work-around to fix this. A warning messages is printed, and we will remove
the work-around at the end of 2016.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
2016-02-11 21:37:17 +01:00
Hans de Goede
cc8d698fab Revert "common/memsize.c: Simplify RAM size detection"
This commit breaks bootup on sunxi boards, the get stuck
when running the main u-boot binary at:

CPU:   Allwinner H3 (SUN8I)
I2C:   ready
DRAM:

This reverts commit 8e7cba048b.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-02-10 08:34:42 -05:00
David Müller (ELSOFT AG)
928f605455 Remove unused CONFIG_MODEM_SUPPORT option and associated dead code.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
2016-02-08 10:22:44 -05:00
Masahiro Yamada
776babd784 board_r: fix a typo in comment block
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08 10:22:41 -05:00
Masahiro Yamada
0cb389dd1a image: fix getenv_bootm_size() function again
Commit 9c11135ce0 ("image: fix getenv_bootm_size() function") fixed
the case where "bootm_low" is defined, but "bootm_size" is not.
Instead, it broke the case where neither "bootm_low" nor "bootm_size"
is defined.  Fix this function again.

Fixes: 9c11135ce0 ("image: fix getenv_bootm_size() function")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Matthias Weisser <m.weisser.m@gmail.com>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2016-02-08 10:22:40 -05:00
Stephen Warren
ee05fedc6c malloc: solve dead code issue in memalign()
The recent change to memalign() caused the allocation failure detection
code to be dead code; the "retry" logic is always activated under the same
condition that the original failure detection code is, and also fully
handles any possible failures. This patch solves the presence of dead
code.

Two alternatives are possible:

a) Delete the now-dead test, and rely on the "retry" path to handle any
allocation problems, as it does.

b) Make the "retry" path fall through to the existing (currently dead)
failure detection code, thus making it not-dead.

(b) was chosen since it reduces the diff between U-Boot's and the upstream
dlmalloc. This should make it marginally easier to import a new version of
dlmalloc in the future.

Reported by: Coverity Scan
Fixes: 4f144a4164 ("malloc: work around some memalign fragmentation issues")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08 10:22:38 -05:00
Eddy Petrișor
8e7cba048b common/memsize.c: Simplify RAM size detection
The case of memory of size 0 is not that different from a memory of any other
size, so we remove the duplicate code and treat the small differences when it
is the case.

Signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
2016-02-08 10:10:49 -05:00
Marek Vasut
f3b267b3a2 hush: Add rudimentary support for PS1 and PS2
Add trivial support for changing the U-Boot command prompt string
by setting PS1 and PS2 environment variables. Only static variables
are supported.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08 10:10:37 -05:00
Marek Vasut
13d3046fa3 hush: Pull out U-Boot prompt display and read functionality
Pull the code which displays U-Boot prompt and reads the command line
into a separate function. No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08 10:10:36 -05:00
Andreas Fenkart
167f525871 tools: env validate: pass values as 0-based array
passing argv/argc can produce off-by-one errors

Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
2016-02-08 10:10:29 -05:00
Tom Rini
57dc53a724 Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging 2016-02-08 09:48:04 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Stefan Roese
9f73690ceb autoboot.c: Fill env vars in process_fdt_options() only if TEXT_BASE is set
The x86 build target "efi-x86" has no TEXT_BASE configured. And with the
introduction of CONFIG_BOOTDELAY for x86, this function is now called
for this board as well. Resulting in compile errors for this target.

Without TEXT_BASE it makes no sense to fill these values. So lets only
configure the env variable if TEXT_BASE is defined.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-05 12:47:20 +08:00
Stephen Warren
4f144a4164 malloc: work around some memalign fragmentation issues
Use of memalign can trigger fragmentation issues such as:

// Internally, this needs to find a free block quite bit larger than s.
// Once the free region is found, any unaligned "padding" immediately
// before and after the block is marked free, so that the allocation
// takes only s bytes (plus malloc header overhead).
p = memalign(a, s);
// If there's little fragmentation so far, this allocation is likely
// located immediately after p.
p2 = malloc(x);
free(p);
// In theory, this should return the same value for p. However, the hole
// left by the free() call is only s in size (plus malloc header overhead)
// whereas memalign searches for a larger block in order to guarantee it
// can adjust the returned pointer to the alignment requirements. Hence,
// the pointer returned, if any, won't be p. If there's little or no space
// left after p2, this allocation will fail.
p = memalign(a, s);

In practice, this issue occurs when running the "dfu" command repeatedly
on NVIDIA Tegra boards, since DFU allocates a large 32M data buffer, and
then initializes the USB controller. If this is the first time USB has
been used in the U-Boot session, this causes a probe of the USB driver,
which causes various allocations, including a strdup() of a GPIO name
when requesting the VBUS GPIO. When DFU is torn down, the USB driver
is left probed, and hence its memory is left allocated. If "dfu" is
executed again, allocation of the 32M data buffer fails as described
above.

In practice, there is a memory hole exactly large enough to hold the 32M
data buffer than DFU needs. However, memalign() can't know that in a
general way. Given that, it's particularly annoying that the allocation
fails!

The issue is that memalign() tries to allocate something larger to
guarantee the ability to align the returned pointer. This patch modifies
memalign() so that if the "general case" over-sized allocation fails,
another allocation is attempted, of the exact size the user desired. If
that allocation just happens to be aligned in the way the user wants,
(and in the case described above, it will be, since the free memory
region is located where a previous identical allocation was located),
the pointer can be returned.

This patch is somewhat related to 806bd245b1 "dfu: don't keep
freeing/reallocating". That patch worked around the issue by removing
repeated free/memalign within a single execution of "dfu". However,
the same technique can't be applied across multiple invocations, since
there's no reason to keep the DFU buffer allocated while DFU isn't
running. This patch addresses the root-cause a bit more directly.

This problem highlights some of the disadvantages of dynamic allocation
and deferred probing of devices.

This patch isn't checkpatch-clean, since it conforms to the existing
coding style in dlmalloc.c, which is different to the rest of U-Boot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2016-02-01 17:08:43 -05:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Gong Qianyu
19c31285a3 dm: env_sf: fix saveenv() to use driver model
It might be missed when converting spi_flash_probe() in cmd_sf.c.

This patch refers to commit fbb099183e ("dm: Convert
spi_flash_probe() and 'sf probe' to use driver model").

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:40 -08:00
Tom Rini
b72ae192e3 Merge branch 'master' of git://git.denx.de/u-boot-video 2016-01-26 09:48:07 -05:00
Tom Rini
9c3193f8d0 Merge branch 'master' of git://git.denx.de/u-boot-usb 2016-01-25 17:23:19 -05:00
Marek Vasut
bdbcbe752e usb: kbd: Prevent out of bound access
Scan code 0x39 is CapsLock, which is not a printable character and thus
is not covered by either usb_kbd_numkey_shifted[] or usb_kbd_numkey[].
Fix the scan code check to avoid looking it up in either of the arrays.

Signed-off-by: Marek Vasut <marex@denx.de>
2016-01-25 22:00:46 +01:00
Tom Rini
3da5240925 common/console.c: Remove unused inline functions
clang-3.8 reports that these functions are unused, remove them.  As this
is the last part of CONFIG_MODEM_SUPPORT_DEBUG, drop that from README.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-25 10:39:47 -05:00
Clemens Gruber
e92029c0f4 env_mmc: support overriding mmc dev from board code
This enables boards to choose where to/from the environment should be
saved/loaded. They can then for example support using the same device
(dynamically) from which the bootloader was launched to load and save
env data and do not have to define CONFIG_SYS_MMC_ENV_DEV statically.

In my use case, the environment needs to be on the same device I
booted from. It can be the eMMC or an optional SD card.
I therefore would override mmc_get_env_dev in the board code, read the
CPU registers to determine where we booted from and return the
corresponding device index.

Cc: Tom Rini <trini@konsulko.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-25 10:39:46 -05:00
Purna Chandra Mandal
8d4f11c203 bootm: fix size arg of flush_cache() in bootm_load_os().
Variable _load_end_ points to end address of uncompressed buffer
(*not* uncomress_buffer_end / sizeof(ulong)), so multipling uncompressed
size with sizeof(ulong) is grossly incorrect in flush_cache().
It might lead to access of address beyond valid memory range and hang the CPU.

Tested on MIPS architecture by using compressed(gzip, lzma)
and uncompressed uImage.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-25 10:39:45 -05:00
Simon Glass
72a8cf8dcc Move all command code into its own directory
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.

Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.

Unfortunately, with m68k I get this error:

m68k:  +   M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o

I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
2016-01-25 10:39:43 -05:00
Andreas Neubacher
e32951b525 lcd: fix the color testpattern in 16bit mode
The testpattern of the lcd was only working in 8bit mode(2x3 tiles in
different colors). With this patch now 8bit and 16bit is supported.
In 16bit mode there are 2x4 tiles in different colors.
The number of LCD-colors is defined in the include/configs/<boardfile>.h

Signed-off-by: Andreas Neubacher <neubacher.andreas@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2016-01-24 00:38:40 +01:00
Simon Glass
66280e82f7 gpio: Warn about invalid GPIOs used with the 'gpio' command
At present there is no indication that an invalid GPIO is used except that
the GPIO status is not displayed. Make the error more explicit to avoid
confusion.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
35a1f0dfa1 stdio: Correct a build error with driver model
When driver model is used for video but not for the keyboard, a compiler
warnings is produced. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
0ffe6ab521 gpio: Allow 's' as an abbreviation for 'status'
The 'gpio' command allows abbreviations for most subcommands. Allow them
for 'status' also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
931b24c5a0 dm: pmic: Add 'reg status' to show all regulators
It is convenient to be able to see the status of all regulators in a list.
Add this feature to the 'reg status' command.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Simon Glass
3ade5bc4dc dm: video: sandbox: Convert sandbox to use driver model for video
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:16 -07:00
Simon Glass
e3b81c1c0d dm: stdio: video: Plumb the video uclass into stdio
Register video drivers with stdio so that they can be used for text output.
This needs to be done explicitly for now. At some point we should be able to
convert stdio itself to driver model and avoid this step.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
Simon Glass
b01c7923e3 dm: video: Implement the bmp command for driver model
This command can use the bitmap display code in the uclass. This is similar
to the code in lcd.c and cfb_console.c. These other copies will go away when
all boards are converted to use driver model for video.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
Simon Glass
5a54194515 dm: common: Add memory reservation for the video uclass
Before relocation we need to reserve memory for the video driver frame
buffers so that they can use this memory when they start up (after
relocation). Add a call to the uclass to permit this.

The current top and bottom of the region is stored in global_data so that
it can be checked post-relocation to ensure enough memory is available. No
video device should be probed before relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
Simon Glass
8703ef3fdb common: Move LCD and video memory reservation together
These two functions are conceptually the same. Move them together in the
pre-relocation init.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
Simon Glass
6cbf5de708 dm: lcd: Avoid using the lcd.h header file with driver model
The LCD functions and definitions are not used with the driver model video
uclass. When all boards are converted over we can remove the file. For now,
use #ifdef to omit the contents.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
Bin Meng
9f29aeb89d Revert "fdt_support: Add multi-serial support for stdout fixup"
This reverts commit 3e303f748c.

The fix up in the /aliases node does not work under the following
scenarios:
- Not every non-DM serial driver was written to have a driver name
  that conforms the format of "serial%d" or "eserial%d".
- With driver model serial, the stdio_devices[] stores the serial
  device node name in the device tree.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-01-20 19:10:12 -07:00
Simon Glass
4ef7909970 usb: Define USB_MAX_STOR_DEV in only one place
We can define this in the header file and use it in usb_storage.c. There is
no need to define it twice. Remove the #define from usb_storage.c.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-01-20 19:06:23 -07:00
Simon Glass
72b335e91d sandbox: Support the bmp command
Adjust this command to use map_sysmem() correctly so that it works on
sandbox.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:22 -07:00
Simon Glass
4fbd258e69 i2c: Correct command return values
We should not return a -ve error code from command functions. Instead,
return CMD_RET_FAILURE. This avoids the "exit not allowed from main input
shell" error messages from the hush shell.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
2016-01-20 19:06:22 -07:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Masahiro Yamada
9c11135ce0 image: fix getenv_bootm_size() function
Currently, this function returns wrong size if "bootm_low" is defined,
but "bootm_size" is not.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-19 08:31:11 -05:00
Peng Fan
447b9cdf2c common: usb: fix checking condition
We support max USB_MAXENDPOINTS, so need to use
"epno >= USB_MAXENDPOINTS", but not "epno > USB_MAXENDPOINTS".
If use ">", we may exceeds the array of if_desc->ep_desc.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
2016-01-16 07:06:55 +01:00
Simon Glass
af7a55514a x86: Fix board init breakage
Commit ecc30663 ("Fix board init code to respect the C runtime environment")
breaks x86. This was mentioned on https://patchwork.ozlabs.org/patch/548644
but not addressed. Correct it so that x86 boards boot again.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-15 08:09:46 -05:00
Ben Whitten
192bc6948b Fix GCC format-security errors and convert sprintfs.
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 22:11:34 -05:00
Peng Fan
db18f548cb common: env_flags: fix loop condition when using env_flags_varaccess_mask
We should use ARRAY_SIZE, but not sizeof. The size of
env_flags_varaccess_mask is 16bytes, but we only need 4 loops.
If using 16 as the end condition, we may access memory that
not belong to array env_flags_varaccess_mask.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-13 21:05:26 -05:00
Peng Fan
bb08a6e7d5 common: cli_simple: use strlcpy instead of strcpy
Report Coverity log:
Destination buffer too small (STRING_OVERFLOW)
string_overflow: You might overrun the 1024 byte destination string
lastcommand by writing 1025 bytes from console_buffer

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:26 -05:00
Michael van Slingerland
4e42e29fd6 cmd_boot: Add a poweroff command
Add a 'poweroff' command to boot commands, this only gets enabled if the
board Kconfig does a "select CMD_POWEROFF".

Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
[hdegoede@redhat.com: Make the cmd conditional on a CMD_POWEROFF Kconfig]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-13 21:05:25 -05:00
Stephen Warren
02585eb3b5 ums: support multiple LUNs at once
Extend the ums command to accept a list of block devices. Each of these
will be exported as a separate LUN. An example use-case would be:

ums 0 mmc 0,0.1,0.2

... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW
partitions. This is useful since it allows the host access to everything
on the eMMC without having to somehow stop the ums command from executing
and restart it with different parameters.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:19 -05:00
Stephen Warren
873cc1d777 mmc: store hwpart in the block device
This will allow us to have multiple block device structs each referring
to the same eMMC device, yet different HW partitions.

For now, there is still a single block device per eMMC device. As before,
this block device always accesses whichever HW partition was most recently
selected. Clients wishing to make use of multiple block devices referring
to different HW partitions can simply take a copy of this block device
once it points at the correct HW partition, and use each one as they wish.
This feature will be used by the next patch.

In the future, perhaps get_device() could be enhanced to return a
dynamically allocated block device struct, to avoid the client needing to
copy it in order to maintain multiple block devices. However, this would
require all users to be updated to free those block device structs at some
point, which is rather a large change.

Most callers of mmc_switch_part() wish to permanently switch the default
MMC block device's HW partition. Enhance mmc_switch_part() so that it does
this. This removes the need for callers to do this. However,
common/env_mmc.c needs to save and restore the current HW partition. Make
it do this more explicitly.

Replace use of mmc_switch_part() with mmc_select_hwpart() in order to
remove duplicate code that skips the call if that HW partition is already
selected.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:19 -05:00
Stephen Warren
7c4213f6a5 block: pass block dev not num to read/write/erase()
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:18 -05:00
Albert ARIBAUD
adc421e4ce arm: move gd handling outside of C code
As of gcc 5.2.1 for Thumb-1, it is not possible any
more to assign gd from C code, as gd is mapped to r9,
and r9 may now be saved in the prolog sequence, and
restored in the epilog sequence, of any C functions.

Therefore arch_setup_gd(), which is supposed to set
r9, may actually have no effect, causing U-Boot to
use a bad address to access GD.

Fix this by never calling arch_setup_gd() for ARM,
and instead setting r9 in arch/arm/lib/crt0.S, to
the value returned by board_init_f_alloc_reserve().

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:18 -05:00
Albert ARIBAUD
ecc306639e Fix board init code to respect the C runtime environment
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.

Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-13 21:05:17 -05:00
Tom Rini
774da4b9aa Merge git://git.denx.de/u-boot-net 2016-01-13 21:05:16 -05:00
Tom Rini
48ad68deb8 hash.c: Conditionally compile hash_command, static hash_show
The function hash_show is now only called by hash_command, so mark it as
static (and drop from hash.h).  We only call hash_command when any of
CONFIG_CMD_CRC32, CONFIG_CMD_SHA1SUM or CONFIG_CMD_HASH are set.  Since
hash.c is linked in unconditionally we must take extra care with
functions that bring in read-only strings as these will not be
discarded.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:08 -05:00
Masahiro Yamada
20e072f374 image: check "bootm_low" and "bootm_size" if "initrd_high" is missing
To boot Linux, we should prevent Initramdisk and FDT from going too
high.

Currently, boot_relocate_fdt() checks "fdt_high" environment first,
and then falls back to getenv_bootm_mapsize() + getenv_bootm_low()
if "fdt_high" is missing.

On the other hand, boot_ramdisk_high() only checks "initrd_high" to
get the address limit for the Initramdisk.  We also want to let this
case fall back to getenv_bootm_mapsize() + getenv_bootm_low().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 09:54:46 -05:00
Simon Glass
9fbdb94667 dm: pci: scsi: Use driver-model PCI API
Adjust the SCSI command to use driver model for its PCI interface.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12 10:19:09 -07:00
Simon Glass
f3f1faefcc dm: pci: Add a dm_ prefix to pci_bus_find_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.

For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_bus_find_bdf() accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12 10:19:09 -07:00
Rasmus Villemoes
fea6730e1c fix always succesful memory test
Since 51209b1f42 ("Use common mtest iteration counting"),
do_mem_mtest has always reported 0 errors and hence returned 0, even
if errors were detected. Fix the helpers mem_test_alt() and
mem_test_quick() to return the number of errors found.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2016-01-08 10:15:47 -05:00
Przemyslaw Marczak
71105f50fe fdt: fix address cell count checking in fdt_translate_address()
Commit: dm: core: Enable optional use of fdt_translate_address()

Enables use of this function as default, but after this it's not
possible to get dev address for the case in which: '#size-cells == 0'

This causes errors when getting address for some GPIOs, for which
the '#size-cells' is set to 0.

Example error:
'__of_translate_address: Bad cell count for gpx0'

Allowing for that case by modifying the macro 'OF_CHECK_COUNTS',
(called from )__of_translate_address(), fixes the issue.

Now, this macro doesn't check, that '#size-cells' is greater than 0.

This is possible from the specification point of view, but I'm not sure
that it doesn't introduce a regression for other configs.

Please test and share the results.

Tested-on: Odroid U3, Odroid X2, Odroid XU3, Sandbox.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2016-01-07 11:28:04 -07:00
Simon Glass
8a83487030 dm: usb: Add a remove() method for USB keyboards
At present USB keyboards are not properly removed with driver model. Add the
code to handle this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-01-07 11:28:03 -07:00
Simon Glass
70caa97108 usb: Allow up to 7 storage devices
The current limit of 5 is not enough for the driver model USB tests. Really
we should not have a limit but the driver model code still uses the
usb_dev_desc[] array, which has a limit.

Increasing the limit by 2 should not bother anyone. Adjust it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-01-07 10:27:07 -07:00
Peng Fan
5d49b4cdf9 common: nvedit: use snprintf instead of sprintf
Use snprintf to replace sprintf.

Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"

Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-04 12:25:36 -05:00
Peng Fan
5a6894397a common: env: initialize scalar variable
Before calling hsearch_r, initialize callback entry to NULL.

Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"

Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-04 12:25:35 -05:00
Peng Fan
09a788624d common: cli: avoid memory leak
Whether CONFIG_SYS_HUSH_PARSER is defined or not, should always
check to free 'buff' to avoid memory leak.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-04 12:25:35 -05:00
Stefan Brüns
faa7db24a4 usb: Move determination of TT hub address/port into separate function
Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).

The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
2015-12-31 16:16:29 +01:00
Stefan Brüns
c75f57fba4 usb: Alloc buffer for USB descriptor dynamically
The configuration descriptor includes all interface, endpoint and
auxiliary descriptors (e.g. report, union) so 512 bytes may not be enough.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-31 10:05:31 +01:00
Bin Meng
bc393a7954 fdt: Rewrite the logic in fdt_fixup_ethernet()
Currently in fdt_fixup_ethernet() the MAC address fix up is
handled in a loop of which the exit condition is to test the
"eth%daddr" env is not NULL. However this creates unnecessary
constrains that those "eth%daddr" env variables must be
sequential even if "ethernet%d" does not start from 0 in the
"/aliases" node. For example, with "/aliases" node below:

    aliases {
        ethernet3 = &enet3;
        ethernet4 = &enet4;
    };

"ethaddr", "eth1addr", "eth2addr" must exist in order to fix
up ethernet3's MAC address successfully.

Now we change the loop logic to iterate the properties in the
"/aliases" node. For each property, test if it is in a format
of "ethernet%d", then get its MAC address from corresponding
"eth%daddr" env and fix it up in the dtb.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On OMAP4 Panda (+v4.3 kernel)
Tested-by: Tom Rini <trini@konsulko.com>
2015-12-21 19:56:17 -06:00
Bin Meng
52d825cc7b fdt: Deprecate "usbethaddr" usage in fdt_fixup_ethernet()
In fdt_fixup_ethernet() only "usbethaddr" is handled to fix up the
first usb ethernet port MAC address. Other additional usb ethernet
ports are ignored as there is no logic to handle "usbeth%daddr".

It is suggested we should use "ethaddr" for all ethernet devices.
Hence deprecate "usbethaddr" usage in fdt_fixup_ethernet().

This actually reverts commit b1f49ab8c7
"ARM: fdt support: Add usbethaddr as an acceptable MAC".

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On OMAP4 Panda (+ v4.3 kernel)
Tested-by: Tom Rini <trini@konsulko.com>
2015-12-21 19:55:27 -06:00
Tom Rini
123b701779 Merge branch 'master' of git://git.denx.de/u-boot-usb 2015-12-17 21:46:04 -05:00
Stephen Warren
e4b70d8035 usb: kbd: don't use int xfers when polling via ctrl xfers
When CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP is enabled, use a
GET_REPORT control transfer to retrieve the initial state of the
keyboard. This matches the technique used to poll the keyboard state.
This is useful since it eliminates the remaining use of interrupt
transfers from the USB keyboard driver, which allows it to work with
USB HCD that don't support interrupt transfers.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2015-12-17 21:54:41 +01:00
Tom Rini
35065cdd94 Merge git://git.denx.de/u-boot-rockchip 2015-12-16 14:50:03 -05:00
Alexey Brodkin
52bc7c7e2b eeprom: fix eeprom write procedure
This fixes commit 1a37889b0a:
----------------------->8--------------------
eeprom: Pull out the RW loop

Unify the code for doing read/write into single function, since the
code for both the read and write is almost identical. This again
trims down the code duplication.
----------------------->8--------------------

where the same one routine is utilized for both EEPROM writing and
reading. The only difference was supposed to be a "read" flag which
in both cases was set with 1 somehow.

That lead to a missing delay in case of writing which lead to write
failure (in my case no data was written).

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
2015-12-16 10:31:31 -05:00
Tom Rini
e6e3faa5c2 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-12-14 20:27:23 -05:00
Aneesh Bansal
9711f52806 armv8/ls1043ardb: add SECURE BOOT target for NOR
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:35 +08:00
York Sun
aabd7ddb88 common: Rewrite hiding the end of memory
As the name may be confusing, the CONFIG_SYS_MEM_TOP_HIDE reserves
some memory from the end of ram, tracked by gd->ram_size. It is not
always the top of u-boot visible memory. Rewrite the macro with a
weak function to provide flexibility for complex calcuation. Legacy
use of this macro is still supported.

Signed-off-by: York Sun <yorksun@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-15 08:57:33 +08:00
York Sun
e81495224f Reserve secure memory
Secure memory is at the end of memory, separated and reserved
from OS, tracked by gd->secure_ram. Secure memory can host
MMU tables, security monitor, etc. This is different from PRAM
used to reserve private memory. PRAM offers memory at the top
of u-boot memory, not necessarily the real end of memory for
systems with very large DDR. Using the end of memory simplifies
MMU setup and avoid memory fragmentation.

"bdinfo" command shows gd->secure_ram value if this memory is
marked as secured.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:32 +08:00
Eric Nelson
5915517b7b spl: mmc: use block device number, not hard-coded 0
In order to support boot from multiple devices through board_boot_order,
it's necessary to use the block number of a device.

The use of a hard-coded 0 for the device number also creates a need
to re-order block devices for use in SPL like this:
	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195

Signed-off-by: Eric Nelson <eric@nelint.com>
2015-12-14 13:42:50 -05:00
Stephen Warren
653447b407 part: fix "part list ... -bootable varname" to use hex
Unfortunately U-Boot assumes that almost all numbers are in hex, including
partition numbers passed to e.g. "load". So, the command "part list mmc 0
-bootable devplist" should use hex when writing partition numbers into
$devplist, so they'll be correctly interpreted.

Change-Id: I9a70b19749643876baadb45efbc3decaef8bfee2
Fixes: 0798d6fd41 ("part: Add support for list filtering on bootable partitions")
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2015-12-13 20:22:01 -05:00
Sjoerd Simons
4363de63a8 spl: use panic_str instead of panic
For a simple static string, use panic_str() which prevents calling
printf needlessly.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-13 17:07:30 -07:00
Nishanth Menon
8405b8d98a common: cli_hush: Fix up simple typo
Correct the spelling for character..

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-12 15:56:10 -05:00
Miao Yan
b3b522f247 VxWorks: fixup MAC address for VxWorks
VxWorks 7 kernels retrieve 'local-mac-addr' from dtb and use
that for NIC MAC address. As a result, when booting the same
kernel image on multiple boards, there will be address
conflicts.

So fixup MAC address when booting VxWorks 7 kernels

Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-12 15:56:08 -05:00
Bin Meng
2317cf0970 common: Remove timer_init() call for x86
With driver model timer support, there should not be an explict
call to timer_init(). Remove this call for x86.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-12-09 17:44:49 +08:00