Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. DCD should not be present in images that will be verified
by software using HAB RVT authentication APIs. Newer versions of HAB
will generate an error if a DCD pointer is present in an image being
authenticated by calling the HAB RVT API. Older versions of HAB will
process and run DCD if it is present, and this could lead to an incorrect
authentication boot flow.
It is highly recommended this check is in place to ensure additional HAB
verified images do not include a DCD table.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it is not possible to run CMD_DEK on i.MX SPL targets:
=> dek_blob 0x12000000 0x12001000 128
The system hangs after running dek_blob because the CAAM clock is being
disabled by the HAB code. There is no need to disable CAAM clock after
authenticating additional boot images, thus keep CAAM clock enabled to
address this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Based on reading over the GCC manual, passing both -m2a and -m2a-nofpu
are redundant, as -m2a-nofpu will provide functional code for both. As
-m2a-nofpu functions with more toolchains and does what is expected,
switch.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When FASTBOOT is activated, only one the supported device is supported in
code at the same time
- CONFIG_FASTBOOT_FLASH_MMC_DEV
- CONFIG_FASTBOOT_FLASH_NAND_DEV
But Today the choice is not exclusive in Kconfig
and that cause Kconfig issue when :
- CONFIG_FASTBOOT, CONFIG_MMC, CONFIG_NAND are activated
- CONFIG_FASTBOOT_FLASH_MMC_DEV = 0
- CONFIG_FASTBOOT_FLASH_NAND_DEV is not activated
The patch add a choice in Kconfig to select the FLASH provider
- CONFIG_FASTBOOT_FLASH_MMC
- CONFIG_FASTBOOT_FLASH_NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix two build warnings when building for arm64:
drivers/dfu/dfu_tftp.c: In function ‘dfu_tftp_write’:
drivers/dfu/dfu_tftp.c:59:37: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
ret = dfu_write_from_mem_addr(dfu, (void *)addr, len);
^
and
drivers/dfu/dfu_tftp.c: In function ‘dfu_tftp_write’:
drivers/dfu/dfu_tftp.c:41:8: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 4 has type ‘__kernel_size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: image name: %s strlen: %u\n", __func__, sb, strlen(sb));
^
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Clean up the screaming mess of configuration options that DFU is.
It was impossible to configure DFU such that TFTP is enabled and
USB is not, this patch fixes that and assures that DFU TFTP and
DFU USB can be enabled separatelly and that the correct pieces
of code are compiled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
If SYS_STDIO_DEREGISTER is not selected and USB_KEYBOARD is selected
U-Boot cannot be built due to missing function stdio_deregister_dev.
So USB_KEYBOARD should select SYS_STDIO_DEREGISTER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The SDP protocol contains multiple 32bit pointers. Add a helper function
to get a valid pointer from these values and use it.
This fixes the following warnings:
drivers/usb/gadget/f_sdp.c: In function ‘sdp_rx_data_complete’:
drivers/usb/gadget/f_sdp.c:347:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy((void *)sdp->dnl_address, req->buf + 1, datalen);
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_jump_imxheader’:
drivers/usb/gadget/f_sdp.c:625:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
entry = (void *)headerv2->entry;
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_handle_in_ep’:
drivers/usb/gadget/f_sdp.c:668:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy(&data[1], (void *)sdp_func->dnl_address, datalen);
^
drivers/usb/gadget/f_sdp.c:679:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
status = sdp_jump_imxheader((void *)sdp_func->jmp_address);
^
Signed-off-by: Andre Heider <a.heider@gmail.com>
If some configs are disabled, number of freqs array will not assigned to
correct value with bus_mode.
Synchornize the ordering with enum bus_mode in mmc.h.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This commit fixes several issues:
- After moving env related code to ./env directory the env_common.o file
is no longer present in the system (has been replaced with built-in.o).
- Use ${OBJCOPY} if available, fallback to system default's objcopy if not
present.
- Extend the script to accept different build directory than current one.
It is extremely handy with OE usage, where source code is separated from
build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
When booting from a non-MMC device, the MMC sub-system may not be
initialized when the environment is first accessed.
We need to make sure that the MMC sub-system is ready in even a non-MMC
boot case.
Therefore, initialize mmc before loading environment from it.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
These ARM boards are in nice shape and still being used a lot
with e.g. QEMU, so I can maintain them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using omap_hsmmc without the device model then the allocation
of mmc->priv ends up uninitialised.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
The correspondence between mmc versions as used in u-boot and the version
numbers reported in register EXT_CSD_REV is wrong for versions above and
including MMC_VERSION_4_41. All those versions were shifted by one:
real 4.5 hardware appeared to be MMC_VERSION_5_0.
Fix this by adding the missing version in the correspondence table.
Reported-by: eil Eilmsteiner Heribert <eil@keba.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
After settings the speed of the sd with the switch command, a check is
done to make sure that the new speed has been set. The current check has a
masking error: speed are encoded on 4 bits only.
Fix it by masking the upper bits.
This fixes a problem seen with QEmu emulating a vexpress-a15.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The UHS modes are not supported in beagle-x15 because it's not possible to
switch the IO lines supply voltage to 1.8v.
Also HS200 cannot be supported on mmc2, because the IO lines of mmc2 are
connected to 3.3v.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the new compatible string "ti,dra7-hsmmc" that was specifically
added for dra7 and dra72. This is required since for dra7 and dra72
processors iodelay values has to be set unlike other processors.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc core has defined a new parameter *clk_disable* to gate the clock.
Disable the clock here if *clk_disable* is set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).
Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
