Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.
Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.
The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.
Signed-off-by: Suman Anna <s-anna@ti.com>
This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF
to signal when we need it. Enable it from the STPMIC1 config and in
sandbox.
The config flag is transitionary, that is it can be removed after all
poweroff implementations use sysreset, and just have CMD_POWEROFF depend
on sysreset.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
It seems that SYSRESET_POWER_OFF was added recently, and all previous code
used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a
PMIC-level power cycle, not a poweroff.
(Comment by Simon Glass)
SYSRESET_POWER means to do a power reset (removing and reinstating all power)
SYSRESET_POWER_OFF means to turn the device off and leave it off
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
(Update comment to help understand the patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The socfpga gen5 SPL manually zeroed bss in board_init_f(). Now that the
DDR driver does not use bss any more, bss is not used before board_init_r()
and we can remove this hack.
bss is normally zeroed by crt0.S, but after board_init_f(), before
board_init_r(). socfpga just had this double-zeroing because it invalidly
used bss in board_init_f() already (during DDR initialization).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
A previous commit...
commit 2a51e16bd5 ("configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default")
...causes the System Firmware version string during SPL boot to no longer
getting printed to the console as expected. To fix this issue rework the
handling of that string to only use basic printf() syntax rather than
for example disabling CONFIG_USE_TINY_PRINTF on affected devices, this
way maintaining most of the memory size benefit the initial patch brings
when it comes to SPL.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add needed device-tree nodes to support PCIe 0
and SERDES on AM65x SoC. The nodes are kept
disabled by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Add support for fastboot_set_reboot_flag() by storing the reboot
flag in the common code to be used by the custom PSCI reboot handler.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor offers multiple services, like returning the
SoC unique serial number, and can provide the "reboot reason" as
set by the previous booted system.
This extends the Amlogic specific "sm" cmd with a "reboot_reason" subcommand
to print or set a specified environment variable with the reboot reason in
human readable format.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor offers multiple services, like returning the
SoC unique serial number, already used to generate an unique MAC
address.
This adds a new, Amlogic specific, "sm" cmd with a "serial" subcommand
to write the SoC unique serial to memory.
This "cm" command will be extended in further patches.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Linux 5.2-rc1 sei510 DT from 5f9e832c1370 ("Linus 5.3-rc1") for the
meson-g12a-sei510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds devicetree for Hikey960 board. Most of the contents are
copied from Linux kernel with some modifications for u-boot. To be
more precise, SD card's speed related properties are removed due to a
bug in u-boot clock implementation. Hence forcing the SD controller to
work in standard speed.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a few bits of platform code to support R8A77980 V3H SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When mainline kernels reboot TK1 they use SW_RESET,
that reset mode does not reset PMIC. Some rails
need to be off for RAM Re-repair to work correctly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
This adds missing hifsys reset parts in header files.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
