Commit graph

12512 commits

Author SHA1 Message Date
Ran Wang
15d59b5316 armv8: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
9d1cd910f7 armv8: Add workaround for USB erratum A-008997
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2a8a353958 armv8: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2ab1553f08 armv8: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
9a609a8800 armv8: Add scfg_clrsetbits_32(), scfg_clrbits_32()
Some erratum patch might need it to program registers.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
17d066fc5d armv8: fsl-layerscape: Support to add RGMII for ls1088aqds
This patch adds support for RGMII protocol

NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
7769776a60 armv8: ls1088aqds: Add support of LS1088AQDS
This patch add support of LS1088AQDS platform.

The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
e84a324ba7 armv8: ls1088ardb: Add support for LS1088ARDB platform
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>

WIP: disable NAND for LS1088ARDB
2017-09-11 08:00:13 -07:00
Ashish Kumar
6d9b82d085 armv8: ls1088a: Add NXP LS1088A SoC support
LS1088A is compliant with the Layerscape Chassis Generation 3 with
eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4
SDRAM memory controller with ECC, Data path acceleration architecture
2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs),
QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Suresh Gupta
22c51855bf armv8: fsl-layerscape: Fix final MMU table for QSPI and IFC
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Ran Wang
5436c6a347 armv8: fsl: Use correct conditional compile for ls1012a
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Ashish Kumar
c055cee195 armv8: fsl-lsch3: Make CCN-504 related code conditional
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Udit Agarwal
15e7c681e1 LS2080ARDB: QSPI boot: Secure Boot image validation
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Sumit Garg
06fb06f66c SECURE_BOOT: Unify memory map for Layerscape based platforms
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Ashish Kumar
63b2316c5c fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.

This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Chris Packham
f58ad98a62 usb: net: migrate USB Ethernet adapters to Kconfig
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08 10:23:00 -04:00
Chris Packham
ae3584498b usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08 10:21:46 -04:00
Kever Yang
0532ceef30 rockchip: enable SPL_SYSRESET config for all Rockchip SoCs
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.

References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-08 11:45:19 +02:00
Kever Yang
e1f6881367 rockchip: rk3328: fix syscon id table
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-08 11:44:51 +02:00
Tom Rini
08d0c53d6b Merge git://git.denx.de/u-boot-rockchip 2017-09-05 07:11:46 -04:00
Wadim Egorov
40d4f79b81 rockchip: rk3288: Add reset reason detection
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-05 11:04:35 +02:00
Tom Rini
a0e80c97c9 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-09-04 22:17:59 -04:00
Marek Vasut
0d0915bef7 ARM: rmobile: Add missing IPSR18 bits to R8A7795 PFC
The IPSR18 register bits were missing from the R8A7795 ES2.0+ PFC
tables, which triggered a BUG() in sh_pfc driver. This is because
of an out-of-bounds access to the pinmux_gpios[] array in the PFC
tables, which was too short due to the missing IPSR18 bits.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-05 07:51:39 +09:00
Bin Meng
3fe6e6e2aa x86: baytrail: acpi: Add full reset bit to the reset register value in FADT
It was noticed a few times, that the reboot from Linux (reboot command)
is different from the reboot (reset command) under U-Boot. The U-Boot
version does seem to reset the board more deeply (PCI cards etc) than
the Linux reboot.

This is actually caused by missing full reset bit in the reset register
value in the ACPI FADT table.

Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
2017-09-02 23:35:55 +08:00
Adam Ford
edd1653f04 Convert CONFIG_SPL_OMAP3_ID_NAND to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_OMAP3_ID_NAND

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-01 20:45:26 -04:00
Adam Ford
fc760cc6e8 Convert CONFIG_SYS_I2C_BUS_MAX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 20:44:30 -04:00
Adam Ford
ac1d8ac871 Configs: Migrate I2C_BUS_MAX to CONFIG_SYS_I2C_BUS_MAX
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-01 17:56:20 -04:00
Tom Rini
48f6232e58 Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
  not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:21 -04:00
Tom Rini
0b6e5b2c48 Merge git://git.denx.de/u-boot-sunxi 2017-09-01 13:30:19 -04:00
Dave Prue
6ff005cf19 sunxi: Fix CONFIG_SUNXI_GMAC references
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)

Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-09-01 20:48:27 +05:30
Tom Rini
6aee2ab68c Merge git://git.denx.de/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/imx6qdl_icore_mmc_defconfig
	configs/imx6qdl_icore_rqs_defconfig
2017-09-01 10:40:59 -04:00
Tom Rini
4109d70293 Merge git://git.denx.de/u-boot-marvell 2017-09-01 10:33:21 -04:00
Tom Rini
e4adc8ed3c Merge git://git.denx.de/u-boot-uniphier
- add {ofnode,dev}_read_resource_byname
- provide DT probe hook to Denali NAND driver
- update clk/reset driver
- update DT
- misc cleanups
2017-09-01 10:32:35 -04:00
Tom Rini
9ec61dbc80 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-09-01 10:31:07 -04:00
Jagan Teki
46668df5d0 i.MX6Q: spl: Fix falcon to use dram_init_banksize
Memory dt node update introduced by spl_fixup_fdt() in below
commit was making DDR configuration in-appropriate
to boot falcon mode. Hence added dram_init_banksize for
explicit assignment of  proper base and size of DDR.

"boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot"
(sha1: 6e7585bb64)

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-30 12:18:26 +02:00
Stefan Agner
624da53ca8 imx: remove SATA boot mode for i.MX 6UL and 6ULL
The NXP i.MX 6UL and 6ULL do not support SATA and have no SATA
boot mode, hence remove it from the boot device detecion. This
fixes a build error introduced with 3bd1642d4d ("imx: fix USB
boot mode detection for i.MX 6UL and 6ULL")

Fixes: 3bd1642d4d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-30 12:17:53 +02:00
Chris Packham
dbc3e64fd1 ARM: mvebu: add "spi-flash" compatible string
U-boots spi-nor support is currently considered a work in progress. For
now to avoid issues it is necessary to add a "spi-flash" compatible
string. Eventually the "jedec,spi-nor" will be sufficient when the core
U-boot code is updated to support it.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-08-30 10:03:35 +02:00
Masahiro Yamada
d8a10e7fac ARM: uniphier: set system bus pinmux for PXs3
The system bus is not enabled by default for NAND, eMMC boot
etc. of PXs3.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Masahiro Yamada
b173c19663 ARM: uniphier: move CONFIG_NAND to defconfig
This imply was added when the option was moved by the moveconfig tool,
but the intention is not clear.  Move it to defconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Masahiro Yamada
31c86aa7fd ARM: dts: uniphier: update PXs3 SoC/board DT
Support PXs3 SoC and its reference development board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Masahiro Yamada
6c9e46efae ARM: dts: uniphier: sync with Linux
Import updates queued up for Linux 4.14-rc1.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Dai Okamura
4013bbb1f3 ARM: uniphier: fix DSPLL init code for LD20 SoC
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:07:04 +09:00
Masahiro Yamada
e0daca7de5 ARM: uniphier: remove ad-hoc pin settings for NAND
This is now set up by the pinctrl driver when the NAND driver is
probed.  Remove the legacy code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:06:57 +09:00
Masahiro Yamada
4914a68de7 ARM: uniphier: add PLL settings for PXs3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:03:11 +09:00
Masahiro Yamada
a55957b9ad ARM: uniphier: move PLLCTRL register macros to each SoC .c file
The new SoC PXs3 changed the address of PLL, but still uses the
same PLL name.  We can not define SC_*PLLCTRL in the common header.
Move them to per-SoC .c file.  Also, fix some PLL comments.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:03:11 +09:00
Masahiro Yamada
546197b986 ARM: uniphier: replace <common.h> with <linux/delay.h> in pll settings
The #include <common.h> was added for mdelay().  Later, the declaration
of mdelay was moved to <linux/delay.h> by commit 5bc516ed66 ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").

There is no need to include <common.h> now.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:03:11 +09:00
Anatolij Gustschin
ffc36f57bc imx6: don't include unneeded boot_mode array in SPL
The soc_boot_modes array is only used by bmode command
and not needed in SPL. Don't include it into SPL.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-29 09:49:51 +02:00
Anatolij Gustschin
ae64226dbe imx: timer: don't clear the GPT control register multiple times
There is no need to clear the control register 100 times in a
loop, a single zero write clears the register. I didn't find any
justification why clearing this register in a loop is needed
(no info in i.MX6 errata or GPT timer linux driver, linux driver
uses single write to clear this control register).

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-08-29 09:47:28 +02:00
Maxime Ripard
343ff16106 sunxi: Enable MMC new mode for A83T
The eMMC controller for the A83T uses the new operating mode. Enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-28 22:36:48 +05:30
Maxime Ripard
de9b1771c3 mmc: sunxi: Support new mode
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.

Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.

Add support for it through a Kconfig option.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-28 22:36:44 +05:30
Bin Meng
0d1414bd97 sandbox: Add a dummy invalidate_dcache_range() function
This adds invalidate_dcache_range() so that some drivers can build
without error on sandbox.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-28 07:17:16 -04:00
Breno Lima
3aa4b703b4 imx: imx6: Move gpr_init() function to soc.c
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28 09:48:53 +02:00
Tom Rini
34f98a3d2e sh: Fix linking of ms7722se
While it is true that we no longer have 'ppcenv' and similar sections,
including env/embedded.o at all results in the text/etc sections being
available for the rest of the link.  This in turn is required for the
setup used on ms7722se.  This also, likely, needs further fine-tuning.

Fixes: f40ad66fa0 ("arch/sh: don't bring common/env_embedded.o into the link")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-27 11:50:16 -04:00
Tom Rini
bd95e655b2 Merge git://git.denx.de/u-boot-sh 2017-08-26 15:10:49 -04:00
Tom Rini
f72b96ec8f Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-08-26 15:10:46 -04:00
Tom Rini
0031af9ce7 Merge git://git.denx.de/u-boot-x86 2017-08-26 15:10:40 -04:00
Vikas Manocha
1e87f9ced4 spl: stm32: make falcon mode activation configurable
With this change, it will be possible to de-select falcon mode & spl
will only boot U-Boot.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Suggested-by: Bo Shen <voice.shen@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-26 14:56:13 -04:00
Ruchika Gupta
a797f274d7 ARMv8/sec_firmware : Update chosen/kaslr-seed with random number
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.

sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.

Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
2017-08-26 14:56:11 -04:00
Thomas Petazzoni
225bfd3906 arch/arm/cpu/arm926ejs/spear/cpu.c: guard do_switch_ecc() with CONFIG_NAND_FSMC
do_switch_ecc() calls fsmc_nand_switch_ecc(), which is a direct
function call into drivers/mtd/nand/fsmc_nand.c. However, this
function is not guarded by CONFIG_NAND_FSMC, which results to a build
failure if CONFIG_NAND_FSMC is disabled.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2017-08-26 14:56:10 -04:00
Thomas Petazzoni
c25c4fd010 board/spear/common: move code to arch/arm/cpu/arm926ejs/spear/
The code in board/spear/common/ is not board-specific but
SoC-specific. Therefore, boards from other vendors than "spear" may
want to re-use this code, which is currently difficult with the code
being placed in board/spear/common/.

Since this code really is SoC-specific, this commit moves it to
arch/arm/cpu/arm926ejs/spear/, with the rest of the SPEAr related
code.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2017-08-26 14:56:10 -04:00
Wenyou.Yang@microchip.com
fc6adebbc1 board: atmel: Use the new PIT timer driver
Use the Atmel PIT timer driver which supports the driver model
and device tree.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-08-26 14:56:09 -04:00
Wenyou.Yang@microchip.com
47edaea494 driver: timer: Add the Atmel PIT timer driver
Add the new Atmel PIT timer driver, which supports the driver model
and device tree.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-08-26 14:56:08 -04:00
Tom Rini
deff9b1d2a powerpc: Rework interrupt_init_cpu()
The function interrupt_init_cpu() is given an int return type but does
not return anything but 0.  Rework this to be a void function.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
2017-08-26 14:56:08 -04:00
Suniel Mahesh
528f2b66dc arm: dts: am33xx: sync DTS with Linux 4.13-rc4
This re-syncs AM33xx DTS file with current file from
Linux v4.13-rc4 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from mmc,
mac, lcdc and tscadc sub nodes.

Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-26 14:56:07 -04:00
Thomas Petazzoni
f40ad66fa0 arch/sh: don't bring common/env_embedded.o into the link
The linker script for SuperH brings the .ppcenv and .ppcenvr section
of common/env_embedded.o into the .text section. However, the .ppcenv
section is only ever filled in by env_embedded.o when
CONFIG_SYS_USE_PPCENV is defined, but no platforms in mainline U-Boot
use this.

In addition, common/env_embedded.o is not always built (when you use
CONFIG_ENV_IS_NOWHERE for example), which causes the following build
failure:

Fixes:

  LD      u-boot
/home/thomas/sh4aeb-linux-musl/bin/sh4aeb-linux-ld.bfd: cannot find common/env_embedded.o

We fix this by no longer adding the .ppcenv and .ppcenvr sections from
common/env_embedded.o into the .text section.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26 07:40:36 +09:00
Thomas Petazzoni
90340c87e5 arch/sh: allow building in big-endian mode
The SuperH architecture allows to be run in either little or big
endian mode. Some SuperH SoCs get the little vs. big endian decision
through mode pins sampled at reset, so if big endian has been choosen
by HW designers, it cannot be easily changed.

Therefore, it makes sense to allow building U-Boot for SuperH in big
endian mode. To allow this, the only change needed is to adjust the
OUTPUT_FORMAT() in the linker script.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2017-08-26 07:38:39 +09:00
Marek Vasut
46933dfbe1 ARM: rmobile: Add u-boot, dm-pre-reloc to clock nodes on Gen3
We need the clock available very early, add the u-boot,dm-pre-reloc
DT property on those nodes, so they come up very in the process.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26 07:04:49 +09:00
Stefan Agner
962c78b1df imx: use BOOT_DEVICE_BOARD instead of UART
i.MX 6 serial downloader is not necessarily booting via UART but can
also boot from USB. In fact only some i.MX chips have serial
downloader support via UART (e.g. 6UL/ULL and Vybrid) but all of
them have serial downloader support via USB. Use the more appropriate
BOOT_DEVICE_BOARD define which is used for ROM provided recovery
mechanisms in general.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-08-25 13:31:47 +02:00
Stefan Agner
3bd1642d4d imx: fix USB boot mode detection for i.MX 6UL and 6ULL
Add the reserved boot mode used in the bmode command for i.MX 6UL
and 6ULL as introduced in commit 3fd9579085 ("imx: mx6ull: fix USB
bmode for i.MX 6UL and 6ULL").

Also replace BMODE_UART with BMODE_RESERVED, which is more appropriate.
Commit 96aac843b6 ("imx: Use IMX6_BMODE_* macros instead of numericals")
added macros for boot modes, in the process the reserved boot mode got
named BMODE_UART. We use the reserved boot mode in the bmode command to
let the boot ROM enter serial downloader recovery mode. But this is only
a side effect, the actual boot mode is reserved...

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-08-25 13:31:31 +02:00
Bin Meng
438505fe69 x86: tangier: kconfig: Guard tangier-specific options
These options should not be exposed to other platforms.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-08-24 11:00:47 +08:00
Bin Meng
81c727d86c x86: baytrail: Fix turbo enable
CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED must be turned on for Baytrail.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-24 11:00:47 +08:00
Bin Meng
2ddb1a177a x86: Convert CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED to Kconfig
This converts CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED to a Kconfig option.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-24 11:00:47 +08:00
Bin Meng
c11b17c6bf x86: kconfig: Imply CMD_PCI
Let's imply the 'pci' command to access the de facto interconnect
bus in an x86 system.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Bin Meng
1e6ebee667 x86: fsp: Configure SPI opcode registers before SPI is locked down
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.

This introduces a Kconfig option CONFIG_FSP_LOCKDOWN_SPI for such
FSPs. When it is on, U-Boot will configure the SPI opcode registers
before the lock-down.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Stefano Babic
7c09cbf68b imx: fix licensing in i.MX files
Some files for i.MX do not yet have the SPDX ID to reference the correct
license.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2017-08-23 10:45:45 +02:00
Peng Fan
fa85b0217d imx: mx7: psci: add copyright and license
Add copyright and license header.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-08-23 10:45:25 +02:00
Masahiro Yamada
3444d1d40e ARM: dts: uniphier: add dr_mode property to dwc3 node
Since commit 576e3cc700 ("usb: host: xhci-dwc3: Add dual role mode
support from DT"), warning is displayed if dr_mode is not specified.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:07:02 +09:00
Masahiro Yamada
c5161eee38 Revert "ARM: uniphier: fix ROM boot mode for PH1-sLD3"
This reverts commit 82d075e79f.

Commit 82d075e79f ("ARM: uniphier: fix ROM boot mode for PH1-sLD3")
was a workaround for sLD3.  Now the sLD3 SoC support has been removed.

Revert it to allow to simplify the init code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Masahiro Yamada
0aa8b2c3e0 Revert "ARM: uniphier: move lowlevel debug init code after page table switch"
This reverts commit bcc51c1512.

Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3.  Now the sLD3 SoC support has been removed.

Revert it to allow to enable lowlevel debug earlier.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Masahiro Yamada
00aa453ebf ARM: uniphier: remove sLD3 SoC support
This SoC is too old.  It is difficult to maintain any longer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Masahiro Yamada
213fcabdfd clk: uniphier: fix unmet direct dependencies warning
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:

  $ make uniphier_v8_defconfig
  warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
  SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)

While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Tom Rini
1fdafb2e3d Merge branch 'master' of git://git.denx.de/u-boot-mmc 2017-08-18 18:24:36 -04:00
Tom Rini
a6dd10c70b Merge branch 'master' of git://git.denx.de/u-boot-coldfire 2017-08-18 18:24:08 -04:00
Kever Yang
a80b3b0378 rockchip: rk322x: update MACRO for mmc clksel reg
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-18 17:52:47 +02:00
Kever Yang
44c5ba557b rockchip: rk322x: update dram bank size
The DRAM start address is not 0, so need to update the last bank size
as:
DRAM start addr + DRAM_SIZE - last bank start addr

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-18 16:55:25 +02:00
Philipp Tomsich
a299a4879e rockchip: rk3399: spl: remove unused header inclusion
fdtdec.h is included, but not used in rk3399-board-spl.c: remove the
'#include'-statement.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-18 16:55:15 +02:00
Kever Yang
caa6b3b530 rockchip: dts: rk3399-evb: remove redundant gmac node
There are two same gmac node, remove one.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-18 16:54:39 +02:00
Angelo Dureghello
a373024e7f m68k: add board stmark2, mcf5441x based
Sysam stmark2 board is a generic and fully (hw and sw) open board, with
a mcf54415 Coldfire CPU, 128MB of DDR2, 16MB of SPI flash and SD card
as non volatile memories, and a wifi module included on-board.
The board is actually used mainly for Coldfire custodian testing activity
related to the mcf5441x Coldfire family.

For further information please see: http://sysam.it/cff_stmark2.html

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
---

Changes in v2:
 - remove CMD_REGINFO
 - add board information in commit message
2017-08-18 01:26:52 +02:00
Angelo Dureghello
02a6eddaba m68k: mcf5445x: allow CS0 to be undefined
On some boards, CONFIG_SYS_CS0_BASE can be undefined, since
CS0 is not connected to any signal.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-08-18 01:26:39 +02:00
Angelo Dureghello
c533cfcd93 m68k: fix cache.c for Coldfire V4E
- fix cache.c CONFIG_CF_V4e to CONFIG_CF_V4E
- fix cache.c to properly enable/disable cache for V4E

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-08-18 01:26:17 +02:00
Angelo Dureghello
c74dda8b44 m68k: mcf5445x: move early ddr init as board-specific
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init
is required. This patch moves this ddr/sdram early initalization
away from start.S (to be board related).

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-08-18 01:26:08 +02:00
Kever Yang
1ade3a9013 rockchip: dts: rk3399-firefly: update gmac parameter
Update the tx_delay and rx_delay to match the timing for
rk3399-firefly board to improve the stability of gmac data
transfer.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-17 10:11:18 +02:00
Simon Glass
e7881d85a9 dm: mmc: Drop CONFIG_DM_MMC_OPS
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:59:55 +09:00
Simon Glass
5ec1f560f3 dm: imx: cm_fx6: Add device tree for cm_fx6
Add this file so we can use device-tree control for cm_fx6. It comes from
linux 4.12.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
7e0712b26e dm: sata: imx: Allow driver model to be used for sata
Update the sata call to work with driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Marek Vasut
a3f0a7d5b5 mmc: sh_sdhi: Fix the ACMD handling
The command handling in this driver is awful, esp. because the driver
depends on command numbers to determine whether this is APPCMD or not.
Also, handling of command RSP response types is totally wrong.

This patch at least plucks out some of the custom command encoding and
fixes the APPCMD handling. The RSP handling still needs work, yet that
might not be needed as it turns out the uniphier-sd.c driver is in much
better shape and supports the same IP, so we might be able to just drop
this driver in favor of the uniphier one.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-17 14:38:02 +09:00
Tom Rini
336aee50cf Merge git://git.denx.de/u-boot-tegra 2017-08-16 18:12:58 -04:00
Tom Rini
ceff355a5f Merge git://git.denx.de/u-boot-sunxi
Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:40 -04:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Simon Glass
723806cc5b env: Rename some other getenv()-related functions
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:

   getenv_vlan()
   getenv_bootm_size()
   getenv_bootm_low()
   getenv_bootm_mapsize()
   env_get_default()

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:31:11 -04:00
Simon Glass
35affd7a2f env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()
Rename this function for consistency with env_get().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:44 -04:00
Simon Glass
bfebc8c965 env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:32 -04:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Simon Glass
fd1e959e91 env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()
Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:56 -04:00
Simon Glass
018f530323 env: Rename common functions related to setenv()
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:32 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Peng Fan
e872f27a02 imx: mx7: fix build warning when CONFIG_IMX_RDC not enabled
Fix build warning when CONFIG_IMX_RDC not defined in defconfig.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16 12:43:09 +02:00
Peng Fan
9402cafb23 imx: mx6sl: simplify code using setbits_le32
Simplify code by removing set_preclk_from_osc with directly setbits_le32.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16 12:43:09 +02:00
Peng Fan
7236297aee imx: mx6sx: select OSC as uart's clk parent
As M4 is sourcing UART clk from OSC, to make UART work
when M4 is enabled, need to select OSC as clk parent,
24M OSC is enough for debug UART in uboot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16 12:43:04 +02:00
Peng Fan
79a57b5ae1 imx: mx6: soc: fix mx6sll settings
There is not LDO_SOC/PU/ARM/MMDC1 on i.MX6SLL, also no need to gate/ungate
all PFDs to make PFD working.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16 11:56:22 +02:00
Peng Fan
3d3598d0f6 imx: mx6: select ARM_ERRATA_845369
Select ARM_ERRATA_845369 for i.MX6DQ/DL/QP.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:51:00 +02:00
Peng Fan
11d94319c3 arm: Implement workaround for Cortex-A9 errata 845369
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:50:51 +02:00
Peng Fan
91435cd40d ARM: i.MX6: exclude the ARM errata from i.MX6 UP system
The ARM errata 751472, 794072, 761320 only applied
to the following configuration:

This erratum affects configurations with either:
- One processor if the ACP is present
- Two or more processors

i.MX6 family does not have the ACP and thus only the MPCore system
will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16 11:50:40 +02:00
Sébastien Szymanski
0c7c6fb764 imx: imx6ull: correct get_cpu_speed_grade_hz
i.MX6ULL has different speed grades than i.MX6UL.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-08-16 11:45:10 +02:00
Sébastien Szymanski
44e670532d imx: imx6ul: correct get_cpu_speed_grade_hz on 696MHz SoCs
Return the correct value when the speed grade is 696MHz.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-08-16 11:44:57 +02:00
Anatolij Gustschin
ff3a5fc46d imx6: clock: correct comment for PLL_VIDEO
This appear to be a copy-paste error, clean it up.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:38:27 +02:00
Anatolij Gustschin
557b9b7250 imx6: use SION macro in SDn_CMD mux mode bitfield arguments
Select SION by appropriate macro instead of constant.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:36:05 +02:00
Simon Glass
01510091de env: Drop saveenv() in favour of env_save()
Use the env_save() function directly now that there is only one
implementation of saveenv().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 20:50:30 -04:00
Simon Glass
c1c3fe2307 env: Convert CONFIG_ENV_IS_IN... to a choice
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).

Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.

Also expand the help for the 'nowhere' option and move it to the top since
it is the default.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-15 20:50:01 -04:00
Marcel Ziswiler
33848eb53e apalis_t30/tk1, colibri_t20/t30: fix i2c bus frequencies
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2017-08-15 14:51:18 -07:00
Marcel Ziswiler
8b733af831 apalis-tk1: remove duplicate hdmi_ddc device tree node
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2017-08-15 14:51:18 -07:00
Simon Glass
0649cd0d49 Move environment files from common/ to env/
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 08:18:45 -04:00
Jagan Teki
585bf8ae6f sun50i: a64: Add A64-OLinuXino initial support
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply

Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:59 +05:30
Jagan Teki
f322657204 sun50i: a64: Add initial NanoPi A64 support
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:19 +05:30
Tom Rini
c1b62ba9ca Merge branch 'master' of git://git.denx.de/u-boot-rockchip 2017-08-14 10:40:01 -04:00
Patrice Chotard
bc5d038445 stm32f1: remove stm32f1 support
A few years ago STM32F1 SoCs support has been added :
0144caf22c  gpio: stm32: add stm32f1 support
2d18ef2364  ARMv7M: add STM32F1 support

But neither STM32F1 dedicated defconfig nor board was
associated to these commits.

Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]

[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:37 -04:00
Nishanth Menon
0459bc30b6 ARM: OMAP5: Enable support for AVS0 for OMAP5 production devices
OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.

Most OMAP5-uEVM boards use the pre-production Class1.5 which has
production efuse registers set to 0. However on production devices,
these are set to valid data.

scale_vcore logic is already smart enough to detect this and use the
"Nominal voltage" on devices that do not have efuse registers populated.

On a test production device populated as follows:
MPU OPP_NOM:
=> md.l 0x04A0021C4 1
4a0021c4: 03a003e9                               ....
(0x3e9 = 1.01v) vs nom voltage of 1.06v
MPU OPP_HIGH:
=> md.l 0x04A0021C8 1
4a0021c8: 03400485                               ..@.

MM OPP_NOM:
=> md.l 0x04A0021A4 1
4a0021a4: 038003d4                               ....
(0x3d4 = 980mV) vs nom voltage of 1.025v
MM OPP_OD:
=> md.l 0x04A0021A8 1
4a0021a8: 03600403                               ..`.

CORE OPP_NOM:
=> md.l 0x04A0021D8 1
4a0021d8: 000003cf                               ....
(0x3cf = 975mV) vs nom voltage of 1.040v

Since the efuse values are'nt currently used, we do not regress on
existing pre-production samples (they continue to use nominal voltage).

But on boards that do have production samples populated, we can leverage
the optimal voltages necessary for proper operation.

Tested on:
a) 720-2644-001 OMAP5UEVM with production sample.
b) 750-2628-222(A) UEVM5432G-02 with pre-production sample.

Data based on OMAP5432 Technical reference Manual SWPU282AF (May
2012-Revised Aug 2016)

NOTE: All collaterals on OMAP5432 silicon itself seems to have been
removed from ti.com, though EVM details are still available:
http://www.ti.com/tool/OMAP5432-EVM

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-08-13 15:17:35 -04:00
Nishanth Menon
5796b66651 ARM: OMAP5: Remove OPP_LOW Definitions for ES2.0
ES2.0 descopes OPP_LOW definition. So remove it from macros defined.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-08-13 15:17:35 -04:00
xypron.glpk@gmx.de
d1fe19766b stm32: remove redundant 'else if'
The if in the else branch is superfluous.
We can use a simple if.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:28 -04:00
xypron.glpk@gmx.de
a22bbfda6e arm: mvebu: avoid possible NULL dereference
It does not make sense to check if info is NULL after
dereferencing it.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-13 15:17:28 -04:00
xypron.glpk@gmx.de
a5981734a4 armv7m: mpu_config add missing break
For DEVICE_NON_SHARED the newly assigned value of attr
is overwritten due to a missing break.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:28 -04:00
xypron.glpk@gmx.de
6def7de37b bcm281xx: clock: avoid possible NULL dereference
It does not make sense first to dereference c and then
to check if it is NULL.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
65e8ce29e4 arm: bcm235xx: clk_set_rate avoid possible NULL deref
It does not make sense first to dereference c and then
to check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
b69a0849e7 arm: bcm235xx: avoid possible NULL dereference
It does not make sense to first dereference c and then
check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:26 -04:00
xypron.glpk@gmx.de
9730bcdc2f arm: spear: do not return random value from stack
If the NOR device is not available do not return
a random value from the stack.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:26 -04:00
Kever Yang
95ca100ba7 rockchip: rk322x: update max-frequency for mmc node
mmc using 150000000 as max-frequency like what rk3288 sets.
This can speed up the mmc read/write, the actual mmc clock is:
Before this patch: 37.125M
After this patch: 49.5M

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-13 17:15:09 +02:00
Kever Yang
a2a1bfe175 rockchip: dts: rk322x: add sdmmc device node
add node for sdmmc in dts and rk3229-evb.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-13 17:15:08 +02:00
Kever Yang
18d38d3a94 rockchip: rk322x: set the DDR region as non-secure in SPL
Disable the ddr secure region setting in SPL and the ddr memory
becomes non-secure, every one can access it. the trust firmware
like OPTEE should have the correct setting for it after SPL if
there is one.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-13 17:15:08 +02:00
Kever Yang
bf82e200a9 rockchip: rk3288: fix EMMC_DIV_MASK definition in header
It should be '<<' instead of '<' for _MASK definition, fix it.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:15:08 +02:00
Philipp Tomsich
e8f9ad94bf rockchip: rk3368: spl: move SPL_LDSCRIPT to Kconfig
With the new way of doing things (i.e. the hierarchical selection of
SPL_LDSCRIPT via Kconfig) in place, this moves the SPL_LDSCRIPT setting
for the RK3368 from defconfig back into Kconfig.

With this done, there should be no lingering cases of SPL_LDSCRIPT
outside of Kconfig files.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:15:08 +02:00
Philipp Tomsich
b529993e02 spl: add hierarchical defaults for SPL_LDSCRIPT
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.

As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig.  Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:37 +02:00
Philipp Tomsich
96b9082c64 rockchip: rk3188: rock: adjust for SPL/TPL split
With the changes to split SPL/TPL for the RK3368, I apparently missed
some needed adjustments to the RK3188 Kconfig and rock_defconfig.

This fixes build-issues for the rock board after applying the RK3368
enablement (and SPL/TPL) set that resulted from TPL_SERIAL_SUPPORT,
TPL_ROCKCHIP_BACK_TO_BROM and TPL_TINY_MEMSET being separate symbols
now.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:37 +02:00
Andy Yan
bfc2ed5c22 rockchip: add u-boot specific dts for rk3368 based boards
Device drivers like debug serial, dmc should be enabled before
relocation, so add u-boot.dtsi files to contain devices that
should be marked as dm-pre-reloc.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:36 +02:00
Philipp Tomsich
3159a6fc39 rockchip: rk3368: remove setup of secure timer from TPL/SPL
When using DM timers w/ the timer0 block within the RK3368, we no
longer depend on the ARMv8 generic timer counting.  This allows us to
drop the secure timer initialisation from the TPL and SPL stages.

The secure timer will later be set up by ATF, which starts the ARMv8
generic timer.  Thus, there will be a dependency from Linux to the ATF
through the ARMv8 generic timer... this seems reasonable, as Linux
will require the ATF (and PSCI) to start up the secondary cores anyway
(in other words: we don't add any new dependencies).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:36 +02:00
Philipp Tomsich
bc824cc03a dts: rk3368: make timer0 accessible for SPL and TPL
To use it with the DM timer driver in SPL and TPL, timer0 needs to be
marked as pre-reloc.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:36 +02:00
Philipp Tomsich
e9e5d9d29f dm: timer: normalise SPL and TPL support
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
  decision for each stage and under control of $(SPL_TPL_)TIMER
  instead of having the two-level configuration with TIMER and
  $(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
  not be compiled in

This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:36 +02:00
Philipp Tomsich
5aa49af311 moveconfig: migrate TPL_STACK, TPL_TEXT_BASE and TPL_MAX_SIZE
We can finally drop TPL_STACK, TPL_TEXT_BASE and TPL_MAX_SIZE off the
whitelist (this time it's really happening!) and migrate the setting
(only used on the RK3368-uQ7 so far) into Kconfig.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:35 +02:00
Philipp Tomsich
4cf4378ed0 rockchip: rk3368: mark TPL as not inheriting its stack, text-base and size from SPL
The RK3368 needs to have a different base-address and stack-pointer
for its TPL stage.  Now that we want to do this via Kconfig, we need
to tick the appropriate 'TPL_NEEDS_...' boxes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:35 +02:00
Philipp Tomsich
faa18dbe25 armv8: TPL_STACK will always be defined, so test CONFIG_TPL_NEEDS_SEPARATE_STACK
Now that TPL_STACK has been moved off the whitelist (ok, I'm lying:
the 'moving off the whitelist' part comes in once moveconfig
runs... which will be a few commits down the line) and added to
Kconfig, we need to test CONFIG_TPL_NEEDS_SEPARATE_STACK to see
whether the value from TPL_STACK should be used or whether we try to
inherit whatever SPL uses.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:35 +02:00
Philipp Tomsich
d9d1242b82 rockchip: Kconfig: preset TPL_LDSCRIPT via Kconfig for the RK3368
Set TPL_LDSCRIPT in Kconfig, so we don't have to pollute our
header file.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-13 17:12:34 +02:00