CONFIG_SF_DEFAULT_SPEED is used in SPL SPI to configure and probe the
flash device during DM SPI uclass probing process, if the
spi-max-frequency is not available in the DTB. Currently the max
frequency is not available, because of the probing mechanism in SPI
uclass has not been fully updated to DM.
The CONFIG_SF_DEFAULT_SPEED is set to 1Mhz if a board defconfig
does not specify it. This speed is too slow and result in a few
seconds delay while the u-boot image is loaded from flash. Based on a
survey of the device tree specifications for MVEBU boards, a sane default
value should be 10Mhz. The default of 10Mhz enables an almost
instantaneously loading of the u-boot image.
Note that this patch depends on this patch series (has been merged to
u-boot-marvell/next):
https://lists.denx.de/pipermail/u-boot/2023-March/511038.html
- RESEND: correct spelling of SF_DEFAULT_MODE
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some platforms were not including <cpu_func.h> which sets the prototype
for reset_cpu, and in turn had it set wrong. Correct these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
On high security devices, ROM enables firewalls to protect the OCSRAM
region access during bootup. Only after TIFS has started (and had
time to disable the OCSRAM firewall region) will we have write access to
the region.
So, move scratch board area to HSM RAM.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
To make sure the panic and the reset messages will go out, console flush() should be used.
Sleep periods do not work in early u-boot phase when timer driver is not initialized yet.
Reference: https://lists.denx.de/pipermail/u-boot/2023-March/512233.html
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Rockchip timer driver has been renamed after the fall back compatible.
There's no need to replace the timer compatible in rk3188-radxarock-u-boot.dtsi
anymore, so remove.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable SPL on RK3588 to detect which device it was booted from.
Fixes use of same-as-spl in u-boot,spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from eMMC on a ROCK 3 Model A result in the following:
U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.
Fixes: b44c54f600 ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot source node path for emmc is using the old sdhci name.
Replace with correct mmc name and also add same-as-spl to boot order.
Fixes: 0d61f8e5f1 ("rockchip: rk3568: add boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot on a ROCK 3 Model A result in the following:
No serial driver found
resetting ...
no sysreset
### ERROR ### Please RESET the board ###
Replace bootph- props with u-boot,dm- props to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are multiple shared Kconfig options between R-Car Gen3 and Gen4.
Keep the common options in Kconfig.64 and move the R-Car Gen3 specific
options into separate Kconfig.rcar3 . The Kconfig.rcar3 contains SoC
and board list, which is limited to R-Car Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Introduce common Kconfig symbol for 64bit R-Car platforms and move
common configuration options into it. This is preparatory patch to
prevent duplication of Kconfig lists later on, when Gen4 is added.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull the SYS_SOC Kconfig option to avoid duplication of this option
in Kconfig.{32,64,rza1} . The default value is the same, so just set
it in one location.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Switch ifdef in rmobile_get_prr() to IS_ENABLED() macro.
The CONFIG_RCAR_GEN3 will never have SPL counterpart, so
the IS_ENABLED() macro is the right one here. No functional
change, except for improved build test coverage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
All R-Car Gen3 defconfigs present in U-Boot do enable DTO support,
enable it for all of R-Car Gen3 by default in Kconfig instead, so
that no new boards would miss this functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS208XA RDB/QDS boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the first device tree description was added for the ethernet nodes,
the 2 10G ports on the LS1088ARDB were wrongly described as 'xgmii'.
Fix this by replacing the two last occurrences of 'xgmii' in the device
trees of the Layerscape DPAA2 devices.
Fixes: 68c7c008e8 ("arm: dts: ls1088ardb: add DPMAC and PHY nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
By default enable nand-on-flash-bbt DT flag, so that driver always refers
to the bad block table(bbt) present on the flash device.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
DC3 nand node is not correct, it is showing all partitions under
controller node directly. Create two sub nand nodes with partitions for
each.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
Since the zynqmp boards can run upstream OP-TEE, and having the DT node
present doesn't cause any side effects add it in case someone tries to
load OP-TEE.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230216133921.866786-1-ilias.apalodimas@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
Since we need to support legacy phys with the dwc3 controller,
we enable this quirk on the zynqmp platforms.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221023215649.221726-1-m.grzeschik@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
The node names should be generic and DT schema expects certain pattern:
xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
So far we used inline assembly to inject the actual instruction that
triggers the semihosting service. While this sounds elegant, as it's
really only about one instruction, it has some serious downsides:
- We need some barriers in place to force the compiler to issue writes
to a data structure before issuing the trap instruction.
- We need to convince the compiler to actually fill the structures that
we use pointers to.
- We need a memory clobber to avoid the compiler caching the data in
those structures, when semihosting writes data back.
- We need register arguments to make sure the function ID and the
pointer land in the right registers.
This is all doable, but fragile and somewhat cumbersome. Since we now
have a separate function in an extra file anyway, we can do away with
all the magic and just write that in an actual assembly file.
This is much more readable and robust.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
AM62A7-SK board has 4GB LPDDR4 Micron MT53E2G32D4DE-046 AUT:B part
but only 2GB was enabled early.
Enable full 4GB memory by updating the latter 2GB memory region
which gets mapped to 0x0880000000 i.e. DDR16SS0_SDRAM as referred in
Table 2-1. AM62A Common SoC Memory of AM62Ax TRM [1].
[1] : https://www.ti.com/lit/zip/spruj16
Logs: https://gist.github.com/devarsht/e85b6af89c01ddadb3a62f3e5f196af8
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Synchronize devicetree sources with Linux v6.2.
- Use GIC interrupt definitions
- Add reg properties in USB-glue and SoC-glue node
- Fix node names to follow the generic names list in DT specification
- Add L2 cache and AHCI nodes
- Update nand and pcie nodes
- And some trivial fixes
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
UniPhier DT applies its own USB node for U-Boot due to the USB driver
constrains. After solving this issue, u-boot allows the original USB node.
After switching USB node, synchronization of USB node with Linux becomes
possible.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
As the lastest spear directories are removed, delete the associated entry
in Makefile.
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
count_required_pts()'s complexity is high if mappings are not using the
largest possible block size (due to some other requirement such as tracking
dirty pages, for example).
Let's switch to a method that follows the pattern established with
the add_map() helper, and make it almost instantaneous instead of
taking a large amount of time if 2MB mappings are in use instead of
1GB.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fixup Pierre's commit. Rebase to the
upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 5d756d147e
Link: 6be9330601
In the add_map() function, for each level it populates, it iterates from
the root of the PT tree, making it ineficient if a mapping needs to occur
past level 1.
Instead, replace it with a recursive (and much simpler) algorithm
that keeps the complexity as low as possible. With this, mapping
512GB at level 2 goes from several seconds down to not measurable
on an A55 machine.
We keep the block mappings at level 1 for now though.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fixup Pierre's commit. Rebase to the
upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 96ad729cf4
Link: 6be9330601
Memory used to hold the page tables is allocated from the top of RAM
with no prior initialization and could therefore hold invalid data. As
invalidate_dcache_all() will be called before the MMU has been
initialized and as that function relies indirectly on the page tables
when using CMO_BY_VA_ONLY, these must be in a valid state from their
allocation.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fix checkpatch warnings, and rebased
to the upstream. ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: e3ceef4230
