Remove unused external clocks and make a common definition
for all keystone platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This is just a cosmetic change that makes
the calling of pll init code looks much cleaner.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Register Base addresses are same for PLLs in all
keystone platforms. If a PLL is not available, the corresponding
register addresses are marked as reserved.
Hence use a common definition.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use common devspeed and armspeed definitions.
Also fix reading efuse bootrom register.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are two types of PLL for all keystone platforms:
Main PLL, Secondary PLL. Instead of duplicating the same definition
for each secondary PLL, have a common function which does
initialization for both PLLs. And also add proper register
definitions.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add print_cpuinfo() function and enable
CONFIG_DISPLAY_CPUINFO for keystone platforms,
so that cpu info can be displayed during boot.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.
Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438i/BABIAJAG.html
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This switches the Integrator boards over to using the device model
for its serial ports.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the CONFIG_DM_USB limitation to enable cache support functions.
Tested on SAMA5D3x-EK board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since some driver like ohci, lcd used dcache functions. But m68k don't
implement the invalidate_dcache_range()/flush_dcache_range() functions.
To avoid compiling errors this patch adds an weak empty stub function
for all m68k cpu.
Also each cpu can implement its own implementation. If not implemented
then by default is using an empty function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Angelo Dureghello <angelo@sysam.it>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
The new bitfield value must not be higher than its mask.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Now that mailbox driver supports cache flush and invalidation, we can
enable dcache.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This adds dcache support for dwc2. The DMA buffers must be DMA aligned and
is flushed for outgoing transactions before starting transfer. For
ingoing transactions it is invalidated after the transfer has finished.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Update to apply again on top of DM patches]
Signed-off-by: Tom Rini <trini@konsulko.com>
When using dcache the setup data for the mailbox must be actually written
into memory before calling into firmware. Thus flush and invalidate the
memory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The mailbox buffer is required to be at least 16 bytes aligned, but for
cache invalidation and/or flush it needs to be cacheline aligned.
Use ALLOC_CACHE_ALIGN_BUFFER for all mailbox buffer allocations.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The cacheline is always 32 bytes for arm1176 CPUs, so define it at board
config level for cache handling code.
The ARM Cortex-A7 has a dcache line size of 64 bytes.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
As both cores are similar merge the cache handling code for both CPUs
to arm11 directory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Add hunk to arch/arm/cpu/arm1136/Makefile]
Signed-off-by: Tom Rini <trini@konsulko.com>
Apparently lcd_panel_disable is not defined anywhere, so no config for
an arm1136 board would have set CONFIG_LCD. Remove the unused code.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Using the twl4030 keypad allows booting directly into some special boot modes,
such as recovery or fastboot. the VOL+ key will trigger a boot to recovery while
the VOL- key will trigger a boot to fastboot.
The G (gesture) key remains unused at this point.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
In most cases, userspace will attempt to power off the device with HALT instead
of POWER_OFF, which triggers a reset instead of a proper power off from the
TWL4030. Hence, it is up to the bootloader to actually turn the device off when
there is no reason to turn it on.
A reboot identified with the OMAP reboot mode bits set is acceptable, as well as
a power on reason from either the power button, USB or charger plug.
Other cases should trigger a power off. Note that for the U-Boot reset command
to take effect, we have to fill-in the OMAP reboot bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for resetting the device on a long press on the power button.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the fastboot USB gadget, including flashing to the
internal MMC and reboot to bootloader or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update to use Kconfig for MUSB]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the serial number is correctly defined, we can pass it to the kernel
using the (legacy) ATAG method. It will be automatically passed via device-tree
when enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The OMAP3 has some die-specific ID bits that we can use to give the device a
(more or less) unique serial number. This is particularly useful for e.g. USB.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for the omap3 reboot mode mechanism and exports the reboot
mode via an environment variable, that is used in the boot command to make it
possible to boot from the recovery partition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This allows scanning the twl4030 keypad, storing the result in a 64-byte long
matrix with the twl4030_keypad_scan function.
Detecting a key at a given column and row is made easier with the
twl4030_keypad_key function.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for detecting a few inputs exported by the TWL4030.
Currently-supported inputs are the power button, USB and charger presence.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This change adds more peripherals to Timll DevKit3250 board, namely
MAC and SMSC phy, SLC NAND, GPIO, SPI and I2C.
Also the default serial console is changed to UART5, added an option
to pass device tree blob by means of bootm, predefined environment
variables are slightly extended and reserved space on NAND to store
user defined U-boot environment.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
If a dtb is specified on the command-line, the Android boot image ramdisk
will not be found. Fix this so that we can specify the ramdisk address and
dtb address. The syntax is to enter the Android boot image address for
both the kernel and ramdisk.
Signed-off-by: Rob Herring <robh@kernel.org>
When building the file system the existing code does an insertion into
a linked list. It attempts to speed this up by keeping a pointer to
where the last entry was inserted but it's still slow.
Now the nodes are just inserted into the list without searching
through for the correct place. This unsorted list is then sorted once
using mergesort after all the entries have been added to the list.
This speeds up the scanning of the flash file system considerably.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
If a sector has a CLEANMARKER at the beginning, it indicates that the
entire sector has been erased. Therefore, if this is found, we can skip the
entire block. This was not being done before this patch.
The code now does the same as the kernel does when encountering a
CLEANMARKER. It still checks that the next few words are FFFFFFFF, and if
so, the block is assumed to be empty, and so is skipped.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
The scan code is similar to the linux kernel, but the kernel defines a much
smaller size to scan through before deciding a sector is blank. Assuming
that what is in the kernel is OK, make these two match.
On its own, this change makes no difference to scanning of any sectors
which have a clean marker at the beginning, since the entire sector is not
blank.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
If the flash is slow, reading less from the flash into buffers makes
the process faster.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
jffs2_1pass_read_inode() would read the entire data for each node
in the filesystem, regardless of whether it was part of the file
to be loaded or not. By only reading the header data for an inode,
and then reading the data only when it is found to be part of the
file to be loaded, much copying of data is saved.
jffs2_1pass_list_inodes() read each inode for every file in the
directory into a buffer. By using NULL as a buffer pointer, NOR
flash simply returns a pointer, and therefore avoids a memory copy.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
