Sync the latest SCFW API with below commit
6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add AHAB encrypted boot documentation for i.MX8/8x family devices
covering the following topics:
- How to encrypt and sign the 2nd container in flash.bin image.
- How to encrypt and sign a standalone container image.
Include a CSF example to encrypt 2nd container in flash.bin image.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Catia Han <yaqian.han@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing reset_cpu, in normal case the WDOG_B outputs immediately
after we clean WDA bit. But on mscale, the WDOG_B may be later than
internal reset, and cause PMIC not reset. As we enabled the SD3.0
support, the PMIC must be reset to reset SD card.
Change the reset_cpu to enable the WDOG_B for timeout as well, and set
WDOG timeout to 1s.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Modified from Seb Fagard's downstream patch
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Seb Fagard <sebastien.fagard@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Latest SCFW has removed old MISC SECO commands. So update the codes
to use new SECO commands.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
parameter 'end address' must be inclusive of address range.
Modified from Seb's downstream patch.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the dump of DRAM PLL into "clocks" command
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.
Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.
This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.
The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update clock root table to let it be easy to configure clock at
very early stage. Also the core_sel mux parent should be A53 CLK
root and ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acquire ATF commit hash when booting U-Boot to make user easy
to know the ATF version.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the SIP macro to common header and unify the name to
make others could reuse them.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update is_imx6ull helper to include i.MX6ULZ SoC. i.MX6ULZ could
share same macro, then we no need to add is_imx6ulz in various drivers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP speed grade use same layout as i.MX8MN, so reuse it for i.MX8MP
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mn speed grade fuse uses new definitions as below. So have
to update get_cpu_speed_grade_hz function to match it.
SPEED_GRADE[5:4] SPEED_GRADE[3:0] MHz
xx 0000 2300
xx 0001 2200
xx 0010 2100
xx 0011 2000
xx 0100 1900
xx 0101 1800
xx 0110 1700
xx 0111 1600
xx 1000 1500
xx 1001 1400
xx 1010 1300
xx 1011 1200
xx 1100 1100
xx 1101 1000
xx 1110 900
xx 1111 800
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
According to iMX8MM datasheet (IMX8MMIEC_Rev_D and IMX8MMCEC_Rev_D),
the speed grading for imx8mm is 800Mhz, 1.2Ghz, 1.6Ghz and 1.8Ghz.
Update them to get_cpu_speed_grade_hz function.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP use 0x182 as its ID, so 0xff is not valid to get the cpu type,
extend it to 0x1ff.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All the FEC ethernet clock entries for iMX8MM are missing, while they
are already present on iMX8MQ. Fill in the nodes on iMX8MM, as the FEC
ethernet gets bogus clock information otherwise which makes ethernet
inoperable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This pull request contains bug fixes needed due to the merged changes for
EFI secure boot.
Patches are supplied to identify EFI system partitions.
-----BEGIN PGP SIGNATURE-----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=38oT
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2
This pull request contains bug fixes needed due to the merged changes for
EFI secure boot.
Patches are supplied to identify EFI system partitions.
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Add a few notes about this feature, which is aimed for development.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With chromebook_coral we normally run TPL->SPL->U-Boot. This is the
'bare metal' case.
When running from coreboot we put u-boot.bin in the RW_LEGACY portion
of the image, e.g. with:
cbfstool image-coral.serial.bin add-flat-binary -r RW_LEGACY \
-f /tmp/b/chromebook_coral/u-boot.bin -n altfw/u-boot \
-c lzma -l 0x1110000 -e 0x1110000
In this case U-Boot is run from coreboot (actually Depthcharge, its
payload) so we cannot access CAR. Use the existing stack instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If U-Boot is running from coreboot we need to skip low-level init. Add
an way to detect this and to set the gd flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To support detecting booting from coreboot, move the code which locates
the coreboot tables into a common place. Adjust the algorithm slightly to
use a word comparison instead of string, since it is faster.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the comments to 960KB]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is run from another boot loader, much of the low-level init
needs to be skipped.
Add a flag for this and adjust ll_boot_init() to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is not the first-stage bootloader we don't want to
re-configure the PCI devices, since this has already been done. Add a
check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is not the first-stage bootloader the interrupt and cache init
must be skipped, as well as init for various peripherals. Update the code
to add checks for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is not the first-stage bootloader the FSP-S init must be
skipped. Update it to add a check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to boot the same x86 image on a device with or
without a first-stage bootloader. For example, with chromebook_coral, it
is helpful for testing to be able to boot the same U-Boot (complete with
FSP) on bare metal and from coreboot. It allows checking of things like
CPU speed, comparing registers, ACPI tables and the like.
When U-Boot is not the first-stage bootloader much of this code is not
needed and can break booting. Add checks for this to the FSP code.
Rather than checking for the amount of available SDRAM, just use 1GB in
this situation, which should be safe. Using 2GB may run into a memory
hole on some SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to dump ACPI tables in U-Boot to see what has been generated.
Add a command to handle this.
To allow the command to find the tables, add a position into the global
data.
Support subcommands to list and dump the tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Put this in the context along with the other important pointers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
We always write three basic tables to ACPI at the start. Move this into
its own function, along with acpi_fill_header(), so we can write a test
for this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
We don't actually support tables without an XSDT so we can drop this dead
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Call the new core function to permit devices to write their own ACPI
tables. These tables will appear after all other tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The current code uses an address but a pointer would result in fewer
casts. Also it repeats the alignment code in a lot of places so this would
be better done in a helper function.
Update write_acpi_tables() to make use of the new acpi_ctx structure,
adding a few helpers to clean things up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Devices need to report various identifiers in the ACPI tables. Rather than
hard-coding these in drivers it is typically better to put them in the
device tree.
Add a binding file to describe this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention here is add a forward declaration, not actually declare a
variable. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* don't copy GUIDs for no reason
* shorten print format strings by using variable names
* don't use the run-time table to access exported functions
* check the result of malloc() (fixes Coverity CID 300331)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For EFI_PERSISTENT_MEMORY_TYPE the 'efidebug memmap' command produces an
illegal memory access.
* Add the missing descriptive string for EFI_PERSISTENT_MEMORY_TYPE.
* Replace the check for EFI_MAX_MEMORY_TYPE by the ARRAY_SIZE() macro.
Reported-by: Coverity (CID 300336)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Do not recreate a variable name that we already have as u16 string.
* Check the return value of malloc()
* EFI_NOT_FOUND cannot occur for a variable name returned by
GetNextVariableName(). Remove a print statement.
* Don't copy a GUID for no reason.
* Don't use the run-time service table to call exported functions.
* Don't pass NULL to show_efi_boot_opt_data() (fixes Coverity CID 300338).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
