Commit graph

646 commits

Author SHA1 Message Date
Mike Williams
1626308797 cleanup: Fix typos and misspellings in various files.
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
2011-07-28 21:27:36 +02:00
Wolfgang Denk
cdf1a2328a Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: MX5: Fix broken leftover TO-2 errata workaround
  MX31: Cleanup clock function
  scb9328: Add ARM relocation support
  am3517evm: change console device from ttyS2 to ttyO2
  Remove volatile qualifier in get_ram_size() calls
  TI: TNETV107X Fix Build Error
  ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
  arm: add CONFIG_MACH_TYPE setting and documentation
  arm: add __ilog2 function
  Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
  EfikaMX: Enable EXT2 booting
  EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
  EfikaMX: Use correct imximage.cfg
  MX27: Update to autogenerated asm-offsets.h
  MX5: Update to autogenerated asm-offsets.h
  imx: Add support for zmx25 board
  imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
  imx: Add auto generation of asm-offsets.h for imx25
  imx: Add support for USB EHCI on imx25
  imx: Use correct imx25 reset.c
  imx: Add get_tbclk() function for imx25
  ARM: Update maintainer of board scb9328
  mx27: Make the UART port number explicit
  build: Add targets for auto gen of asm-offsets.h and use it in imx35
  mx31pdk: cosmetic: Fix line over 80 characters
2011-07-18 21:04:56 +02:00
Mingkai Hu
4f1d1b7d1e powerpc/p2041rdb: Add p2041rdb board support
P2041RDB Specification:
-----------------------
Memory subsystem:
 * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 256 Kbit M24256 I2C EEPROM
 * 16 Mbyte SPI memory
 * SD connector to interface with the SD memory card

Ethernet:
 * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
 * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)

PCIe:
 * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2

SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors

USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces

I2C:
 * I2C1: Real time clock, Temperature sensor, Memory module
 * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-17 11:03:36 -05:00
Albert ARIBAUD
a55d23ccf6 Remove volatile qualifier in get_ram_size() calls
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-17 17:11:53 +02:00
Ramneek Mehresh
86dda50484 qoriq/p1_p2_rdb: USB device-tree fixups for P1020
Resolve P1020 second USB controller multiplexing with eLBC
	- mandatory to mention USB2 in hwconfig string to select it
	  over eLBC, otherwise USB2 node is removed
	- works only for SPI and SD boot

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Roy Zang
3f7f6b8592 powerpc/85xx: Add basic support for P1023RDS board
The P1023RDS board is the reference board for the P1023 SoC.

Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
York Sun
939e5bf9b3 powerpc/mpc85xx: Display a warning for unsupported DDR data rates
If DDR initialziation uses a speed table and the speed is not matched,
print a warning message instead of silently ignoring.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
York Sun
79fa00af5d powerpc/corenet_ds: Fix RCW overriding for RDIMM
Allow overriding RCW for all RDIMM, not only quad-rank ones.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Timur Tabi
26fd33b9be powerpc/86xx: display boot device and bank on the MPC8610 HPCD
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00
Kumar Gala
58b2f96e38 powerpc/85xx: Fix compile errors if CONFIG_SYS_DPAA_QBMAN isn't set
Add ifdef protection for qp_info and liodn associated with Q/BMan.  Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.

Also add protection around setup_portals() call in corenet_ds board
code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00
Kumar Gala
be1ff615ea powerpc/85xx: Fix compile errors if CONFIG_SYS_{B,Q}MAN_MEM_PHYS aren't set
Add ifdef protection in LAW & TLB code to handle the case in which
CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a
build.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00
Timur Tabi
f5f30dea2a powerpc/83xx: remove empty board_early_init_f()
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-07-06 19:09:28 -05:00
Fabio Estevam
47c3e074ad MX53: Add initial support for MX53ARD
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-04 10:55:26 +02:00
Timur Tabi
29b83d9833 powerpc/p1022ds: set the clock-frequency prop only if the clock is enabled
The clock-frequency property in an audio codec's device tree node is set to
the input clock frequency for that codec.  On the Freescale P1022DS board,
the input clock is enabled only if the hwconfig 'audclk' option is set.
Therefore, the property should only be set in the device tree if the clock
is actually enabled.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-06-09 15:53:38 -05:00
Fabio Estevam
4ac2e2d69f mx31ads: Use the new relocation scheme
This fixes the MX31ADS build by using the new relocation scheme.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
2011-06-06 09:35:25 +02:00
Jason Liu
5195890440 mx5: board: code clean up for checkboard code
The boot cause code has been factor out to soc common
code,we need drop the part from the board support code

This patch also remove the redundant cpu version print

Signed-off-by: Jason Liu <jason.hui@linaro.org>
2011-05-23 08:36:46 +02:00
Fabio Estevam
860b32ee50 MX53: Add initial support for MX53SMD board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-05-23 08:36:46 +02:00
Jason Liu
938080dc4b MX53: support for freescale MX53LOCO board
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch

Signed-off-by: Jason Liu <jason.hui@linaro.org>
2011-05-23 08:36:46 +02:00
Wolfgang Denk
cd6881b519 Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-19 22:22:44 +02:00
Shaohui Xie
be827c7ab0 powerpc/85xx: add support for env in MMC/SPI on corenet ds boards
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-18 09:15:25 -05:00
Fabio Estevam
b73850f764 MX31: mx31pdk: Add watchdog support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-05-11 23:03:15 +02:00
Wolfgang Denk
aeabdeb7a3 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-04-30 22:45:55 +02:00
Scott Wood
83b7e2a7f2 Handle most LDSCRIPT setting centrally
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk.  Some
are found using an arch-specific rule for looking in CPUDIR, etc.

Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.

Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.

If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.

If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:

$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds

Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules.  These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-30 00:59:47 +02:00
Jiang Yutang
9b6e9d1c13 powerpc/85xx: Enable eSPI support on P1022DS
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29 07:36:17 -05:00
Timur Tabi
82c9dfdc20 powerpc/fsl: add 'pixis_reset dump' command
Add the 'pixis_reset dump' command, which displays the contents of the PIXIS
registers.  This command is only available if DEBUG is defined.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Timur Tabi
eb0d47e181 powerpc/86xx: remove empty board_early_init_f()
Remove an empty board_early_init_f() from the MPC8641HPCN board.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:08:16 -05:00
Timur Tabi
ba8e76bd49 powerpc: use 'video-mode' environment variable to configure DIU
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration.  Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.

The old definition of the "monitor" environment variable only determines
which video port to use for output.  This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port.  The
resolution was hard-coded into board-specific code.  The Linux command-line
arguments needed to be hard-coded to the proper video definition string.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-04-28 21:31:16 +02:00
Kumar Gala
e02aea61cb powerpc: Add P3041DS/P5020DS board support (uses corenet_ds code)
The P3041DS & P5020DS boards are almost identical (except for the
processor in them).  Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.

Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS.  We utilize some of these for SERDES clock
configuration.

Additionally, the P3041DS/P5020DS support NAND.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Ramneek Mehresh
2bad42a0c8 powerpc/85xx: Add support for 2nd USB controller on p1_p2_rdb
Second USB controller only works for SPI and SD boot because of pin muxing

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2011-04-27 22:29:03 -05:00
Fabio Estevam
e9e0790cff MX31: mx31pdk: Make the board name simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-04-27 19:38:05 +02:00
Stefano Babic
8627111543 IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:05 +02:00
Liu Hui-R64343
ec665d75a7 MX53: drop config.mk from mx53evk
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-04-27 19:38:05 +02:00
Stefano Babic
c7bdcb61f3 MX51: drop config.mk from mx51evk
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:04 +02:00
Andy Fleming
865ff85640 fsl: Change fsl_phy_enet_if to phy_interface_t
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:35 -05:00
Andy Fleming
063c12633d tsec: Convert tsec to use PHY Lib
This converts tsec to use the new PHY Lib.  All of the old PHY support
is ripped out.  The old MDIO driver is split off, and placed in
fsl_mdio.c.  The initialization is modified to initialize the MDIO
driver as well.  The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:34 -05:00
Shaohui Xie
2a9fab82b7 powerpc/85xx: Add PBL boot from SPI flash support on P4080DS
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.

Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Jiang Yutang
b93f81a418 powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DS
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Jerry Huang
1ac63e4094 powerpc/85xx: Enable eSDHC boot support on P2020 DS
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 22:26:32 -05:00
Jiang Yutang
9899ac1951 powerpc/85xx: Add 36-bit address map support to P1022DS
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:43 -05:00
Poonam Aggrwal
e0082f7cb4 powerpc/85xx: Add 36-bit physical addressing support for P1_P2_RDB
Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
66c74fca18 powerpc/85xx: Optimized DDR settings for 800MT/s on P1/P2 RDB
Changed the following DDR timing parameters for 800Mt/s:
tRRT    BL/2+1 to  BL/2
tWWT    BL/2+1 to  BL/2
tWRT    BL/2+1 to  BL/2
tRWT    BL/2+1 to  BL/2
REFINT  6500ns to  7800ns

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
3313b20b95 powerpc/85xx: Removed P1/P2 RDB RevB support
RevB boards never really made it outside of Freescale and have been
replaced with RevC & RevD which had various board bug fixes.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Priyanka Jain
cac29f25fd powerpc/85xx: Read board switch settings on p1_p2_rdb
PCA9557 is parallel I/O expansion device on I2C bus which stores various
board switch settings like NOR Flash-Bank selection, SD Data width.

On board:
switch SW5[6] is to select width for eSDHC
        ON  - 4-bit [Enable eSPI]
        OFF - 8-bit [Disable eSPI]

switch SW4[8] is to select NOR Flash Bank for Booting
        OFF - Primary Bank
        ON  - Secondary Bank

Read board switch settings on p1_p2_rdb and configure corresponding
eSDHC width.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Priyanka Jain
0c871e952e powerpc/85xx: Use DDR for RAMBOOT instead of L2 SRAM on p1_p2_rdb
Using DDR as RAMBOOT base instead of L2SRAM for SDCard and SPI Flash
boot loaders because:
- P1_P2_RDB boards have soldered DDR so no need for SPD
- Also P102x has 256K L2 cache size so becomes a limiting factor for
  size of image that could be loaded in SRAM mode and would require three
  stage boot loader (TPL).

Changes done:
 1. CONFIG_SYS_TEXT_BASE to 0x11000000
 2. CONFIG_RESET_VECTOR_ADDRESS to 0x1107fffc

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Timur Tabi
f098c9c880 fsl: obsolete NXID v0 EEPROMs, automatically upgrade them to NXID v1
The NXID EEPROM format comes in two versions, v0 and v1.  The only
difference is in the number of MAC addresses that can be stored.  NXID v0
supports eight addresses, and NXID v1 supports 23.

Rather than allow a board to choose which version to support, NXID v0 is
now considered deprecated.  The EEPROM code is updated to support only
NXID v1, but it can still read EEPROMs formatted with v0.  In these cases,
the EEPROM data is loaded and the CRC is verified, but the data is stored
into a v1 data structure.  If the EEPROM data is written back, it is
written in v1 format.  This allows existing v0-formatted EEPROMs to
continue providing MAC addresses, but any changes to the data will force
an upgrade to the v1 format, while retaining all data.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
York Sun
dea8bd627c powerpc/85xx: Update fixed DDR3 timing table for P4080DS
Most of time U-boot doesn't get an exact clock number. For example, clock
900MHz may be detected as 899.99MHz. 800MHz could be 799.99MHz. Update the
table to align the desired clocks in the middle.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
c39f44dc6f powerpc/8xxx: Refactor fsl_ddr_get_spd into common code from board
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing.  The only variations are in how many
controllers or DIMMs per controller exist.  To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.

We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
5df4b0ad0d powerpc/8xxx: Replace fsl_ddr_get_mem_data_rate with get_ddr_freq()
Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq()
and every 86xx board uses get_bus_freq().  If implement get_ddr_freq()
as a static inline to call get_bus_freq() we can remove
fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq()
directly.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Kumar Gala
00203c6464 powerpc/85xx: Remove config.mk for nand linker script
Move the include of mpc85xx/u-boot-nand.lds to utilize
CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Kumar Gala
561e710a97 powerpc: Move cpu specific lmb reserve to arch_lmb_reserve
We've been utilizing board_lmb_reserve to reserve the boot page for MP
systems.  We can just move this into arch_lmb_reserve for 85xx & 86xx
systems rather than duplicating in each board port.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00