The register offset of i2c_sysc offset is not correct as per
omap5[1]/dra7[2] TRM, correct the offsets as per the
documentation.
[1] - http://www.ti.com/lit/pdf/swpu249
[2] - http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register offset of i2c_sysc offset is not correct as per
omap4 TRM [1], correct the offsets as per the documentation.
[1] - http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.
Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.
Fixes: 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the NAND controller in the sun5i-r8-chip.dts.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add the NAND controller definition to sun5i.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We need some macros to manipulate the NAND controller clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Deassert resets and enable clock signals of xHCI blocks if the
corresponding CONFIG is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to add more board attributes, so the "flags" member will be
handier than separate boolean ones.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sync register macros with Linux code. This will be helpful to
develop the counterpart of Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
[ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As part of the startup process for boards using the SPL, the
meaning of board_init_f changed such that it should return normally
rather than calling board_init_r directly. (see
db910353a1 )
This was fixed in 32-bit arm, but broke when SPL was added to
64 bit arm. This fixes crt0_64 so that it calls board_init_r
during the SPL and removes the direct call from board_init_f
from the arm SPL example.
Signed-off-by: Jeremy Hunt <Jeremy.Hunt@DEShawResearch.com>
Acked-by: Simon Glass <sjg@chromium.org>
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Other payload than uImage is currently considered to be raw U-Boot
image. Check also for zImage in Falcon mode.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make code 64bit aware.
Warnings:
+../arch/arm/lib/spl.c: In function ‘jump_to_image_linux’:
+../arch/arm/lib/spl.c:63:3: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
+../common/spl/spl_fat.c: In function ‘spl_load_image_fat’:
+../common/spl/spl_fat.c:91:33: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.
This reverts commit 4b2fd720a7.
Signed-off-by: Tom Rini <trini@konsulko.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
On Tegra186, U-Boot is booted by the binary firmware as if it were a
Linux kernel. Consequently, a DTB is passed to U-Boot. Cache the address
of that DTB, and parse the /memory/reg property to determine the actual
RAM regions that U-Boot and subsequent EL2/EL1 SW may actually use.
Given the binary FW passes a DTB to U-Boot, I anticipate the suggestion
that U-Boot use that DTB as its control DTB. I don't believe that would
work well, so I do not plan to put any effort into this. By default the
FW-supplied DTB is the L4T kernel's DTB, which uses non-upstreamed DT
bindings. U-Boot aims to use only upstreamed DT bindings, or as close as
it can get. Replacing this DTB with a DTB using upstream bindings is
physically quite easy; simply replace the content of one of the GPT
partitions on the eMMC. However, the binary FW at least partially relies
on the existence/content of some nodes in the DTB, and that requires the
DTB to be written according to downstream bindings. Equally, if U-Boot
continues to use appended DTBs built from its own source tree, as it does
for all other Tegra platforms, development and deployment is much easier.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IVC (Inter-VM Communication) protocol is a Tegra-specific IPC (Inter
Processor Communication) framework. Within the context of U-Boot, it is
typically used for communication between the main CPU and various
auxiliary processors. In particular, it will be used to communicate with
the BPMP (Boot and Power Management Processor) on Tegra186 in order to
manipulate clocks and reset signals.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Many files in arch/arm/mach-tegra are compiled conditionally based on
Kconfig variables, or applicable to all platforms. We can let the main
Tegra Makefile handle compiling (or not) those files to avoid each SoC-
specific Makefile needing to duplicate entries for those files. This
leaves the SoC-specific Makefiles to compile truly SoC-specific code.
In the future, we'll hopefully add Kconfig variables for all the other
files, and refactor those files, and so reduce the need for SoC-specific
Makefiles and/or ifdefs in the Makefiles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.
With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 uses different GPIO port IDs compared to previous chips. Make
sure the SoC DT file includes the correct GPIO binding header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Set the enable-method in the cpu node to PSCI, and create device
node for PSCI, when PSCI was enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the PSCI and PPA is ready, skip the fixup for spin-table and
waking secondary cores. Otherwise, change SMP method to spin-table,
and the device node of PSCI will be removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The FSL Primary Protected Application (PPA) is a software component
loaded during boot which runs in TrustZone and remains resident
after boot.
Use the secure firmware framework to integrate FSL PPA into U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This framework is introduced for ARMv8 secure monitor mode firmware.
The main functions of the framework are, on EL3, verify the firmware,
load it to the secure memory and jump into it, and while it returned
to U-Boot, do some necessary setups at the 'target exception level'
that is determined by the respective secure firmware.
So far, the framework support only FIT format image, and need to define
the name of which config node should be used in 'configurations' and
the name of property for the raw secure firmware image in that config.
The FIT image should be stored in Byte accessing memory, such as NOR
Flash, or else it should be copied to main memory to use this framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function assume that the d-cache and MMU has been enabled earlier,
so it just created MMU table in main memory. But the assumption is not
always correct, for example, the early setup is done in EL3, while
enable_caches() is called when the PE has turned into another EL.
Define the function mmu_setup() for fsl-layerscape to cover the weak
one.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Drop platform code to create static MMU tables. Use common framework
to create MMU tables on the run. Tested on LS2080ARDB with secure and
non-secure ram scenarios.
Signed-off-by: York Sun <york.sun@nxp.com>
Introduce virtual and physical addresses in the mapping table. This change
have no impact on existing boards because they all use idential mapping.
Signed-off-by: York Sun <york.sun@nxp.com>
When page tables are created, allow later table to be created on
previous block entry. Splitting block feature is already working
with current code. This patch only rearranges the code order and
adds one condition to call split_block().
Signed-off-by: York Sun <york.sun@nxp.com>
