Commit graph

893 commits

Author SHA1 Message Date
Kishon Vijay Abraham I
4564faeafb ti: dwc3: Enable clocks in enable_basic_clocks() in hw_data.c
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.

Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-16 15:08:36 -04:00
Tom Rini
20913018fb Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-04-16 12:51:23 -04:00
Paul Kocialkowski
ebd468b2d2 sunxi: common VBUS detection logic in usbc
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.

In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
5eaacb4340 sunxi: usb: Drop AXP-sepcific VBUS detection and drive logic
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Alexey Firago
e2ec3e4612 fastboot: add support for reboot-bootloader command
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.

This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.

Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
2015-04-14 10:19:05 +02:00
Marek Szyprowski
7704fdbda3 usb: gadget: thor: Claim EP after allocating it in thor gadget
Storing thor device struct as an EP private data. It is necessary for
DWC3 operation.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2015-04-14 05:48:12 +02:00
Lukasz Majewski
3621b3b8a7 usb: dwc3: Correct clean up code for requests
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.

This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.

Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Lukasz Majewski
afa093bfa7 usb: dwc3: gadget: Set non EP0 max packet limit to 512B
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.

Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Lukasz Majewski
29e7fc19ce usb: dwc3: gadget: Set all ctrl fields of Transfer Control Blocks (TRB) to be LST
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.

Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.

This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Marek Szyprowski
137f7c590d usb: dwc3: optimize interrupt loop
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2015-04-14 05:48:12 +02:00
Marek Szyprowski
16bece51c5 usb: dwc3: gadget: add common endpoint configuration for dwc3 udc driver
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2015-04-14 05:48:12 +02:00
Marek Szyprowski
5dc4538bf3 usb: dwc3: add a workaround for too small OUT requests
DWC3 hangs on OUT requests smaller than maxpacket size,
so HACK the request length to be at least equal to maxpacket size.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2015-04-14 05:48:12 +02:00
Joonyoung Shim
7e9cb7962f usb: dwc3: make dwc3_set_mode to static
This commit makes the dwc3_set_mode() as static, to prevent collisions.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Lukasz Majewski
2252d150ef usb: dwc3: Remove BIT(x) macro from DWC3's gadget code
The BIT() macro is used only in those places, so it is reasonable to
replace it by a constant value.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Lukasz Majewski
6d69173207 usb: composite: Add .reset callback to usb_gadget_driver structure
DWC3 UDC driver requires presence of .reset callback in a composite driver.
This setting is similar to the one nowadays present in linux kernel.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:12 +02:00
Kishon Vijay Abraham I
2d48aa69bd usb: modify usb_gadget_handle_interrupts to take controller index
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.

Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:11 +02:00
Kishon Vijay Abraham I
04afd5b59b usb: gadget: defer setting maxpacket till ->setup()
Taken from linux kernel with commit
commit 765f5b830e547229bb752e7b232ee83e2b3d49d5
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Thu Jun 23 14:26:11 2011 +0200

usb: gadget: defer setting maxpacket till ->setup()

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:11 +02:00
Kishon Vijay Abraham I
5b9ce0e28a usb: dwc3: Makefile: Make dwc3 driver compile in u-boot
Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
8d488f3e16 usb: dwc3: Add chained TRB support for ep0
dwc3 can do only max packet aligned transfers. So in case request length
is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE
two chained TRBs is required to handle the transfer.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
1f78f8feda usb: dwc3: ep0: preparation for implementing chained TRB
No functional change. Modified few things so that there are no
code duplication while implementing chained TRB.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
526a50f8ec dwc3: flush the buffers before using it
In the linux kernel, non cacheable buffers are used. However in uboot
since there are no APIs to allocate non cacheable memory, all
the buffers should be flushed before using it.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
6900aeda52 usb: dwc3: TI PHY: PHY driver for dwc3 in TI platforms
Added a single driver for both USB2 PHY programming and USB3 PHY
programming.

USB3 PHY is taken from drivers/phy/phy-ti-pipe3.c in linux kernel.
commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload.

USB2 PHY is taken from drivers/phy/phy-omap-usb2.c in linux kernel.
commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe
failure and remove.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
53de33fc00 usb: dwc3: dwc3-omap: add interrupt status API to check for interrupts
Added an API to check for interrupt status. This API is generally
called from board file to check for interrupt status.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
57207657a1 dwc3: dwc3-omap: add support for multiple dwc3-omap controllers
Added support for multiple dwc3 omap controllers. This gives uboot
the capability to control multiple dwc3 omap controllers.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
c241d7eee4 usb: dwc3: dwc3-omap: change probe and remove to uboot init and uboot exit code
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.

This will change once we have dwc3-omap driver adapted to use the uboot
driver model.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
93c3763810 include: dwc3-omap-uboot: add a structure for populating dwc3-omap platform data
Added a structure to populate dwc3 omap platform data. The board file should
populate these platform data before invoking dwc3 omap driver.

This will be removed once dwc3-omap driver is adapted to use the driver model.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
3f52e1b985 usb: dwc3: dwc3-omap: make dwc3-omap build in uboot
*) Changed the included header files to that used in u-boot.
*) Removed extcon_* APIs
*) Removed regulator_* APIs
*) Fixed other misc warnings
*) Added dwc3-omap.h to include the definitions of UTMI modes.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
27d3b89d33 dwc3: core: added an API to invoke irq handlers
Since interrupt support is not present in u-boot, added an
API to handle the interrupts in dwc3 core. This API can be
polled to handle the interrupts.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
793d347f53 dwc3: core: add support for multiple dwc3 controllers
Added support for multiple dwc3 controllers. This gives uboot
the capability to control multiple dwc3 controllers.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:10 +02:00
Kishon Vijay Abraham I
8e1906a81f dwc3: core: change probe and remove to uboot init and uboot exit code
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
71744d0d06 usb: dwc3: core: make dwc3 core build in uboot
*) Changed the include header files to that used in u-boot.
*) Removed phy_* APIs
*) Removed jiffies and used a simple while loop
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) Fixed other misc warnings

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
b6d959acaa usb: dwc3: ep0: make dwc3 ep0 build in uboot
*) Changed the included header files to that used in u-boot.
*) added dwc3_ep_event_string() used in ep0.c
*) Fixed other misc warnings

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
747a0a5b38 usb: dwc3: gadget: make dwc3 gadget build in uboot
Did a bunch of things to get dwc3/gadget.c compile in u-boot without
build errors and warnings
*) Changed the included header files to that used in u-boot.
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) removed sg support
*) remove jiffies and used a simple while loop
*) removed irq support and added a function to call these interrupt handler.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
18be4cb151 usb: dwc3: linux-compat: Add header for dwc3 linux compatibiltiy
Added a header file to include various linux specific APIs like
pr_debug, WARN_ WARN_ON_ONCE etc.. in order to avoid compilation
error while building dwc3 driver.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
027b6103cd usb: dwc3: remove pm related operations from dwc3 driver
Removed all pm related operations including pm_runtime APIs,
suspend/resume hooks as support for these are not present in u-boot.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
9848e5740a usb: dwc3: fix dwc3 header files
Changed the header files included in core.h and io.h to the u-boot header
files so that these files can be included in other dwc3 source files and
be compiled in uboot. Also added otg.h which has the defines for dr_mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
9de1115de7 usb: dwc3: remove trace_* APIs from dwc3 driver
Removed most of the trace_* APIs from dwc3 driver since tracepoints are not
supported in u-boot. Replaced some of the trace_* API with dev_dbg/dev/vdbg.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Review-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:09 +02:00
Kishon Vijay Abraham I
30c31d5897 usb: dwc3: Modify the file headers to u-boot format
Modified the file header to the format that is used in u-boot. Also
included in the header, the commit in linux kernel from which each of
these files are added.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Kishon Vijay Abraham I
97798eb96d usb: dwc3: remove un-used files from dwc3 folder
removed un-used/un-supported files from dwc3. These files can be added
later as and when the support is added.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Kishon Vijay Abraham I
85d5e7075f usb: dwc3: add dwc3 folder from linux kernel to u-boot
Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9)
to u-boot. This will be adapted to work with u-boot in the
following patches.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Kishon Vijay Abraham I
103fa06cfe usb: gadget: udc: make udc-core compile in u-boot build
Make udc-core compile in u-boot by removing all linux specific
stuff and having only the bare minimal udc-core required for
usb gadget drivers. Also modified the file header to a format that is
generally being used in u-boot.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Kishon Vijay Abraham I
a139b96a47 usb: gadget: udc: add udc-core from linux kernel to u-boot
Added udc-core.c from linux kernel 3.19-rc1 (97bf6af1f9) to u-boot.
This will be adapted to work with u-boot in the
following patches.
Adding support for udc will help to seamlessly port dwc3 driver from
linux kernel to u-boot (since dwc3 uses udc-core) and it'll also help
to add support for multiple gadget controllers to be functional at the
same time.
All other gadget drivers can also be adapted to use udc-core.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Stephen Warren
5877de9165 usb: dwc2: retry NAK'd interrupt transfers
IIUC, interrupt transfers are NAK'd by devices until they wish to trigger
an interrupt, and e.g. EHCI controllers retry these in HW until they are
ACK'd. However, DWC2 doesn't seem to retry, so we need to do this in SW.
In practice, I've seen DWC2_HCINT_FRMOVRUN happen too. I'm not quite sure
what this error implies; perhaps it's related to how near the end of a
USB frame we're at when the interrupt transfer is initiated? Anyway,
retrying this temporary error seems to be necessary too.

With all these commits applied, both my USB keyboards (one LS Lenovo and
one FS Dell) work correctly when there is no USB hub between the SoC and
the keyboard; We still need split transactions to be implemented for hubs
to work.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
e236519b73 usb: dwc2: implement interrupt transfers
As best I can tell, there's no difference between bulk and interrupt
transfers in terms of how the HW should be programmed, at least given
that we're executing one transaction at a time rather than scheduling
them into frames for maximum throughput.

This patch ends up sharing the toggle bit state between bulk and
interrupt transfers on a particular EP. However I believe this is fine;
AFAIK a given EP either uses bulk or interrupt transfers and doesn't mix
them.

This patch doesn't do anything with the "interval" parameter for
interrupt transfers, but then most other USB controller drivers in U-Boot
don't either.

It turns out that one of my keyboards is happy to work using control
transfers but the other only gives non-zero "HID reports" via interrupt
transfers.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
ed9bcbc792 usb: dwc2: correctly program hcchar for LS devices
A bit must be set in HCCHAR when communicating with low-speed devices.
I have no idea why there's no corresponding bit to distinguish between
full-speed and high-speed devices, but no matter; they all work now!

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
4748cce573 usb: dwc2: detect device speed correctly
This doesn't make my LS keyboard work any better, but it does at least
report the correct speed in "usb tree".

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
5c0beb5c58 usb: dwc2: use phys_to_bus/bus_to_phys
Use of these APIs is required on the Raspberry Pi. With this change, USB
on RPi1 should be more reliable, and USB on the RPi2 will start working.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
fc909c0563 usb: dwc2: fix bulk transfers
When I created wait_for_chhltd(), I noticed that some instances of the
code it replaced expected the ACK bit to be set and others didn't. I
assumed this was an accidental inconsistency in the code, so wrote
wait_for_chhltd() to always expect ACK to be set. This code appeared to
work correctly for both enumeration of USB keyboards and operation of
USB Ethernet devices. However, this change broke USB Mass Storage (at
least my USB SD card reader). This change reverts to exactly the
original behaviour. I'm not sure why the ACK bit isn't always set
(perhaps a quirk in the USB HW or DWC2 controller), but the code works
this way!

Fixes: 5be4ca7d6ac8 ("usb: dwc2: unify waiting for transfer completion")
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
805b67e1ea usb: dwc2: remove restriction on buffer length
Each USB transfer is split up into chunks that are held in an aligned
buffer. This imposes a limit on the size of each chunk, but no limit on
the total size of transferred data. Fix the logic in chunk_msg() not to
reject large transfers, but simply take the size of the aligned buffer
into account when calculating the chunk size.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
d1c880c66c usb: dwc2: fix aligned buffer usage
The original aligned_buffer usage:
a) Uselessly copied data into the aligned buffer even for IN
   transactions. Fix this my making the copy conditional.
b) Always programmed the HW to transfer to/from the start of the aligned
   buffer. This worked fine for OUT transactions since the memcpy copied
   the OUT data to this location too. However, for large IN transactions,
   since the copy from the aligned buffer to the "client" buffer was
   deferred until after all chunks were transferred. it resulted in each
   chunk's transfer over-writing the data for the first transfer. Fix
   this by copying IN data as soon as it's received.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:59 +02:00
Stephen Warren
66ffc87586 usb: dwc2: simplify wait_for_chhltd
toggle is never NULL. Simplify the code by removing handling of when it
is NULL.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:58 +02:00
Stephen Warren
282685e07e usb: dwc2: remove control_data_toggle[]
The control data toggle resets to DATA1 at the start of the data phase
of every setup transaction. We don't need a global variable to store
the value; we can just store it on the stack.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:58 +02:00
Stephen Warren
ee83755401 usb: dwc2: usb chunk_msg() for control transfers too
This removes duplicated code.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:58 +02:00
Stephen Warren
7b5e504dae usb: dwc2: refactor submit_bulk_msg to be common
Move the body of submit_bulk_msg() into new function chunk_msg(). This
can be shared with submit_control_msg() to reduce code duplication, and
allow control messages larger than maxpacket.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:58 +02:00
Stephen Warren
4a1d21fc52 usb: dwc2: unify waiting for transfer completion
Lift common code out of submit_bulk_msg() and submit_control_msg().

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-14 05:47:58 +02:00
Sergey Temerkhanov
421a5a0c98 usb: 64-bit architectures support for xHCI
This commit allows xHCI to use both 64 and 32 bit memory
physical addresses depending on architecture it's being built for.
Also it makes use of readq()/writeq() on 64-bit systems

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
2015-04-14 05:47:48 +02:00
Thierry Reding
ec5e78cf8a usb: mass-storage: Build warning fixes for 64-bit
Fix a printf format mismatch warning seen on 64-bit builds.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:47:48 +02:00
Thierry Reding
96df9c7e94 usb: ehci-tegra: Build warning fixes for 64-bit
Cast pointers to unsigned long instead of a sized 32-bit type to avoid
pointer to integer cast size mismatch warnings.

Cc: Tom Warren <twarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-14 05:47:48 +02:00
Rob Herring
98ae840a00 ehci-hcd: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
2015-04-14 05:47:47 +02:00
Rob Herring
f72d8320b6 usb: ci_udc: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:47:47 +02:00
Thierry Reding
4c5998b77a usb: eth: asix: Build warning fixes for 64-bit
Fix a type mismatch in a printf format string.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-04-14 05:47:47 +02:00
Hans de Goede
246e3b8787 sunxi: musb: Fix some lo speed devices not working with musb host
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.

The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.

Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-29 12:58:59 +02:00
Bin Meng
a7c3d5e2a9 net: Add ethernet FCS length macro in net.h
Some ethernet drivers use their own version of ethernet FCS length
macro which is really common. We define ETH_FCS_LEN in net.h and
replace those custom versions in various places.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-03-24 21:22:37 -06:00
Paul Kocialkowski
8a440b09f2 sunxi: musb: Return early on VBUS GPIO error instead of on a positive value
This allows printing the error message when VBUS is detected, as it would with
AXP VBUS detect.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-21 13:51:27 +01:00
Masahiro Yamada
6462cdedc2 ARM: UniPhier: adjust device trees for business transfer
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-15 13:37:00 +09:00
Chen-Yu Tsai
e42add561b sunxi: musb: Support checking VBUS using AXP221 PMIC
This enables the musb glue layer to use the AXP221's VBUS detection
function to check for VBUS. This fixes otg support on the A23 q8h
tablets.

Note that u-boot never calls musb_shutdown(), so once VBUS is enabled,
it is never disabled until the system is powered off, or the OS does
so. This can be used to our advantage to keep VBUS powered into the
OS, where support for AXP221 is not available yet.

Fixes: 52defe8f65 ("sunxi: musb: Check Vbus-det before enabling otg port power")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:25 +01:00
Tom Rini
57c6941b43 Merge git://git.denx.de/u-boot-usb 2015-03-02 07:24:27 -05:00
Masahiro Yamada
1e7df7c4e4 usb: UniPhier: add UniPhier on-chip xHCI host driver support
Support xHCI host driver used on Panasonic UniPhier platform.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-03-01 00:03:00 +09:00
Masahiro Yamada
4c7d025368 ARM: UniPhier: move uniphier_ehci_reset() function
Because uniphier_ehci_reset() is only called from ehci-uniphier.c,
it can be a static function there.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-03-01 00:02:49 +09:00
Masahiro Yamada
44f597adeb ARM: UniPhier: remove EHCI platform devices
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig).  Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers.  We still keep UART platform devices because they might
be useful for SPL.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-03-01 00:02:48 +09:00
Masahiro Yamada
a86ac9540e ARM: UniPhier: include <mach/*.h> instead of <asm/arch/*.h>
Since commit 0e7368c6c4 (kbuild: prepare for moving headers into
mach-*/include/mach), we can replace #include <asm/arch/*.h> with
<mach/*.h> so we do not need to create the symbolic link during the
build.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-03-01 00:02:18 +09:00
Dileep Katta
537cd072da usb: gadget: fastboot: Set the Serial Number for Fastboot Gadget
Configure the serial number using the serial# environment variable
during the fastboot bind.

This enables "fastboot devices" to return the serial number for
the attached devices.

Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-02-25 17:47:02 +01:00
Dileep Katta
9e4b510d40 fastboot: OUT transaction length must be aligned to wMaxPacketSize
OUT transactions must be aligned to wMaxPacketSize for each transfer,
or else transfer will not complete successfully. This patch modifies
rx_bytes_expected to return a transfer length that is aligned to
wMaxPacketSize.

Note that the value of wMaxPacketSize and ep->maxpacket may not be
the same value, and it is the value of wMaxPacketSize that should be
used for alignment. wMaxPacketSize is passed depending on the speed of
connection.

Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-02-25 17:47:02 +01:00
Dileep Katta
897923819c usb: gadget: fastboot: Add fastboot erase
Adds the fastboot erase functionality, to erase a partition
specified by name. The erase is performed based on erase group size,
to avoid erasing other partitions. The start address and the size
is aligned to the erase group size for this.

Currently only supports erasing from eMMC.

Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-02-25 17:47:02 +01:00
Rob Herring
372d7decfe fastboot: add support for "oem format" command
Add "oem format" command to write partition table. This relies on the
env variable partitions to contain the list of partitions as required by
the gpt command.

Note that this does not erase any data other than the partition table.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
2015-02-25 17:47:02 +01:00
Michael Scott
de1956202e fastboot: add "fastboot oem" command support
Add code stub to handle "fastboot oem __" command. As unlock is a common
fastboot command, distinguish that it is not implemented.

Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Steve Rae <srae@broadcom.com>
2015-02-25 17:47:02 +01:00
Paul Kocialkowski
193d7d1530 usb: musb-new: omap2430: Reset the MUSB controller early
When booting from USB peripheral boot, the bootrom will not properly deinit the
MUSB controller, which doesn't clearly indicate an USB disconnection to the host
and leaves U-Boot to deal with the state of the previous USB session.

On some host controller drivers (e.g. xhci_hcd), this ends up in a failure
during set address, caused by the lack of proper disconnection notification.

Resetting the controller early in U-Boot notifies the host of the disconnection
and doesn't hurt other use cases.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
2015-02-24 18:54:03 +01:00
Joonyoung Shim
8f9f7be7af exynos: usb: make dwc3_set_mode to static
The dwc3_set_mode function is used only in
drivers/usb/host/xhci-exynos5.c so make it to static.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
2015-02-24 18:54:03 +01:00
Hans de Goede
52defe8f65 sunxi: musb: Check Vbus-det before enabling otg port power
Sending out 5V when there is a charger connected to the otg port is not a
good idea, so check for this and error out.

Note this commit currently breaks otg support on the q8h tablets, as we need
to do some magic with the pmic there to get vbus info, this is deliberate
(better safe then sorry), fixing this is on my TODO list.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21 16:53:33 +01:00
Hans de Goede
b1b912ddf3 sunxi: otg: Fix peripheral mode
Peripheral mode needs us to signal vusb high to the phy for it to work,
just like the host mode does.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-16 20:05:52 +01:00
Simon Glass
316328f59d usb: pci: Add XHCI driver for PCI
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-05 22:16:42 -07:00
Simon Glass
4fd46727e4 usb: pci: Use pci_find_class() to find the device
Use the new utility function instead of local code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-05 22:16:42 -07:00
Simon Glass
46927e1ef4 dm: usb: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Rene Griessl
1193397592 usb: eth: asix88179: add ability to modify MAC address
This patch enables U-Boot to modify the MAC address of the AX88179.
Tested on RECS5250 (similar to Arndale5250)

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>
2015-01-18 12:31:36 +01:00
Hans de Goede
904f2a83a8 musb-new: Add interrupt queue support
Add interrupt queue support, so that a usb keyboard can be used without
causing huge latencies.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
accf04c2aa musb-new: Add urb and hep parameters to construct_urb
Make construct_urb take an urb and hep parameter, rather then having it always
operate on the file global urb and hep structs. This is a preperation patch
for adding interrupt queue support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
b918a0c6f6 musb-new: Properly remove a transfer from the schedule on timeout
If a transfer / urb times-out, properly remove it from the schedule, rather
then letting it sit on the ep head. This stops the musb code from getting
confused and refusing to queue further transfers after a timeout.

Tested by unplugging a usb-keyboard, replugging it and doing a usb-reset,
before this commit the keyboard would not work after the usb-reset.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
90cdc1039d musb-new: Fix reset sequence when in host mode
This commit fixes a number of issues with the reset sequence of musb-new
in host mode:

1) Our usb device probe relies on a second device reset being done after the
first descriptors read. Factor the musb reset code into a usb_reset_root_port
function (and add this as an empty define for other controllers), and call
this when a device has no parent.

2) Just like with normal usb controllers there needs to be a delay after
reset, for normal usb controllers, this is handled in hub_port_reset, add a
delay to usb_reset_root_port.

3) Sync the musb reset sequence with the upstream kernel, clear all bits of
power except bits 4-7, and increase the time reset is asserted to 50 ms.

With these fixes an usb keyboard I have now always enumerates properly, where
as earlier it would only enumerare properly once every 5 tries.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
e8672e3f0e musb-new: Fix interrupt transfers not working
For bulk and ctrl transfers common/usb.c sets udev->status = USB_ST_NOT_PROC,
but it does not do so for interrupt transfers.

musb_uboot.c: submit_urb() however was waiting for USB_ST_NOT_PROC to become 0,
and thus without anyone setting USB_ST_NOT_PROC would exit immediately for
interrupt urbs, returning the urb status of EINPROGRESS as error.

This commit fixes this, thereby also making usb_kbd.c work together with
musb_new and CONFIG_SYS_USB_EVENT_POLL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
dc9a391270 musb-new: Use time based timeouts rather then cpu-cycles based timeouts
CPU cycle based timeouts are no good, because how long they use depends on
CPU speed. Instead use time based timeouts, and wait one second for a
device connection to show up (per the USB spec), and wait USB_TIMEOUT_MS
for various urbs to complete.

This fixes "usb start" taking for ever when no device is plugged into the
otg port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
28a15ef7fd musb-new: Add sunxi musb controller support
This is based on Jussi Kivilinna's work for the linux-sunxi-3.4 kernel to use
the kernels musb driver instead of Allwinners own custom driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
0f8bc53240 musb-new: Add register defines for different reg layout on sunxi
The sunxi SoCs also have a musb controller, but with a different register
layout.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:36 +01:00
Hans de Goede
8bb6c1d1e0 usb: Add an interval parameter to create_int_queue
Currently create_int_queue is only implemented by the ehci code, and that
does not honor interrupt intervals, but other drivers which might also want
to implement create_int_queue may honor intervals, so add an interval param.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-18 12:31:35 +01:00
Alex Sadovsky
c0978a94aa usb: gadget: pxa25x_udc: fix use-before-initialized bug
Fix use-before-initialized bug in pxa25x_udc driver.

Function usb_gadget_register_driver calls udc_disable,
and udc_disable calls pullup_off that uses dev->mach->udc_command.
But dev->mach is initialized in usb_gadget_register_driver after
calling udc_disable. This patch fixes the order of initialization.

Signed-off-by: Alex Sadovsky <Nable.MainInbox@googlemail.com>
2015-01-18 12:31:01 +01:00
Stefan Roese
1fd81b7c23 usb: gadget: f_dfu: Add get_alt function to pass the USB compliance test
Without this function the USB compliance test (USB 2.0 Command Verifier) will
fail in the "Interface Descriptor Test" with this error message:

FAIL
(1.2.51) A successful GetInterface request must return the alternate setting
set by a prior call to SetInterface.

Lets add this function to read back the value so that the DFU device fully
passes the USB compliance test.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2015-01-18 12:31:00 +01:00
Stefan Roese
87ed6b1067 usb: gadget: composite: Fix NULL pointer crash in USB compliance test
On the DXR2 board (AM335x using MUSB) the USB compliance test suite
(USB 2.0 Command Verifier) will cause the board to crash and reset
upon the "BOS Descriptor Test - Addressed state". Here the output
from the DRX2 while running this test:

GADGET DRIVER: usb_dnl_dfu
musb-hdrc: peripheral reset irq lost!
composite_setup (776)
data abort
pc : [<87f693ac>]          lr : [<87f6911c>]
sp : 86f33a58  ip : 00000000     fp : 86f3bbac
r10: 00000f00  r9 : 86f33ef4     r8 : 86f37da8
r7 : 00000005  r6 : 86f33a90     r5 : 00000000  r4 : 86f37e30
r3 : 00000000  r2 : 00000000     r1 : 87f9c888  r0 : 00000016
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...

By adding the case statement for USB_DT_BOS and therefore not running
into the default case (jump to unkown label) this crash is fixed.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2015-01-18 12:31:00 +01:00
Hans de Goede
0eccec4ef1 sunxi: Move usb-controller init code out of ehci-sunxi.c for reuse for otg
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.

While at it also update various #ifdefs / defines for sun8i support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Rene Griessl
e9954b867c usb: eth: add ASIX AX88179 DRIVER
This patch adds driver support for the ASIX AX88179 USB3.0 to GbE network
adapter.

Driver has been tested on the RECS5250 COM module (similar to ARDALE5250).
Testcase was DHCP and PXE boot.

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>
2014-12-31 19:10:13 +01:00
Przemyslaw Marczak
62a96d805f gadget: f_thor: check pointers before use in download_tail()
Some pointers in function download_tail() were not checked
before the use. This could possibly cause the data abort.
To avoid this, check if the pointers are not null is added.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
2014-12-18 12:26:06 +01:00
Rob Herring
267abc626d fastboot: add support for continue command
The fastboot continue command is defined to exit fastboot and continue
autoboot. This commit implements the continue command and the exiting of
fastboot only. Subsequent u-boot commands can be processed after exiting
fastboot. Autoboot should implement a boot script such as "fastboot; mmc
read <...>; bootm" to fully implement the fastboot continue function.

Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
2014-12-18 12:26:06 +01:00
Rob Herring
fe1b28c9f0 usb, g_dnl: generalize DFU detach functions
In order to add detach functions for fastboot, make the DFU detach related
functions common so they can be shared.

Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
2014-12-18 12:26:05 +01:00
Bo Shen
68ae882596 USB: gadget: atmel_usba_udc: fix transfer hang issue
When receive data, the RXRDY in status register set by hardware
after a new packet has been stored in the endpoint FIFO. After,
we copy from FIFO, we clear it, make the FIFO can be accessed
again.
In the receive_data() function, this bit RXRDY has been cleared.
So, after the receive_data() function return, this bit should
not be cleared again, or else it will cause the accessing FIFO
corrupt, which will make the data loss.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2014-12-16 16:08:50 +01:00
Tom Rini
a5a5882611 Merge git://git.denx.de/u-boot-dm 2014-12-11 20:47:34 -05:00
Tom Rini
fc9b0b8043 Merge branch 'master' of git://git.denx.de/u-boot-usb
Conflicts:
	board/freescale/mx6sxsabresd/mx6sxsabresd.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-12-11 18:40:49 -05:00
Masahiro Yamada
80d9ef8d40 lib: string: move strlcpy() to a common place
Move strlcpy() definition from drivers/usb/gadget/ether.c to
lib/string.c because it is a very useful function.
Let's add the prototype to include/linux/string.h too.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-12-11 13:18:41 -07:00
Nikhil Badola
da5ce448c7 drivers: usb: fsl: Check USB Erratum A007792 applicability
Check USB Erratum A007792 applicability. If applicable, add
corresponding  property in the device tree via device tree fixup

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:41:11 -08:00
Nikhil Badola
ecfc19f31f drivers: usb: fsl: Add USB device-tree errata framework
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:41:03 -08:00
Nikhil Badola
a1c04e2785 drivers: usb: Make usb device-tree fixup code architecture independent
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:40:50 -08:00
Felipe Balbi
7a294c5c0a usb: phy: omap_usb_phy: fix build breakage
there's no such function usb3_phy_power(),
it's likely that author meant to call,
usb_phy_power() instead, but that's already
called properly from xhci-omap.c.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:13 -05:00
Masahiro Yamada
149c751dc7 usb: UniPhier: support OF configuration
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
2014-11-28 02:21:01 +09:00
Tom Rini
85bafb6da4 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2014-11-26 11:23:26 -05:00
Tom Rini
878cd63e02 Merge branch 'master' of http://git.denx.de/u-boot-samsung 2014-11-26 11:21:16 -05:00
Nikhil Badola
f3dff695e1 drivers : usb: fsl: Implement usb Erratum A007798 workaround
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-24 09:27:04 -08:00
Masahiro Yamada
b41411954d linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does.  This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
 - Use min, max, min3, max3 only when the arguments have the same type
   (or add casts to the arguments)
 - Use min_t/max_t instead with the appropriate type for the first
   argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-23 06:48:30 -05:00
Nikhil Badola
c26c80a1a4 drivers: usb: fsl: Move USB Errata checking code
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-21 09:28:28 -08:00
Masahiro Yamada
cba1da495d include: move various macros to include/linux/kernel.h
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.

In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.

Moreover, we are suffering from too cluttered include/common.h.

This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.

Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Masahiro Yamada
f2168440de ARM: remove CONFIG_ARM920T defines
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).

This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Masahiro Yamada
0c6de8853b usb: ehci: do not set the LSB of Current qTD pointer
According to EHCI specification, the LSB of DWORD 3 of Queue Head
(Current qTD Pointer) is not T-bit, but always zero.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-19 23:31:54 +01:00
Suriyan Ramasami
6a23c6533c arm: odroid: usb: add support for usb host including ethernet
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-11-17 19:33:22 +09:00
Peng Fan
229dbba9b1 usb:ehci-mx6 add phy mode query function
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.

Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
2014-11-14 20:56:54 +01:00
Tom Rini
0d485b9095 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2014-11-13 10:35:13 -05:00
Hans de Goede
76946dfe69 sun6i: ehci: Add sun6i ehci support
Add support for the 2 ehci controllers found on the sun6i (A31) soc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
2014-11-13 14:49:02 +01:00
Hans de Goede
115200ceb0 sunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-s
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13 14:49:02 +01:00
Tom Rini
6841deb620 Merge branch 'master' of git://git.denx.de/u-boot-usb 2014-11-11 16:59:25 -05:00
Masahiro Yamada
048899ba8c usb: UniPhier: add UniPhier on-chip EHCI host driver support
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).

TODO for me:
Move the base address to device trees.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-11-12 00:21:28 +09:00
Masahiro Yamada
6e7e9294d3 usb: add basic USB configs in Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-11-12 00:21:18 +09:00
Rene Griessl
3908f16f85 usb: eth: fix Makefile
fix obj-y term

Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>
2014-11-07 22:03:44 +01:00
Nobuhiro Iwamatsu
865ed5eae4 usb: rmobile: Use ARRAY_SIZE(usb_base_address) instead of CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Marek Vasut <marex@denx.de>
2014-11-07 16:32:02 +01:00
Masahiro Yamada
c02bf4582f usb: ehci: fix Interrupt on Doorbell flag of USBCMD
CMD_IAAD (Interrupt on Async Advance Doorbell) is bit 6, not bit 5.
While we are here, sort the flags.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-07 16:32:02 +01:00
Marek Vasut
481a11c552 usb: s3c-otg: Allow custom gusbcfg
Allow passing in a custom configuration of the gusbcfg register
via platform data.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-07 16:32:02 +01:00
Marek Vasut
d1b6c77e1f usb: s3c-otg: Split out PHY control
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-07 16:32:02 +01:00
Marek Vasut
40ff06b958 usb: s3c-otg: Encapsulate PHY control
Encapsulate the Samsung PHY control and its register accesses
into the otg_phy_init() and otg_phy_off() functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-06 21:05:54 +01:00
Marek Vasut
2cc157b0cd usb: s3c-otg: Remove useless include
Remove the useless inclusion of arch/arm/gpio.h , which is completely
bogus in this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-11-06 21:04:20 +01:00
Hans de Goede
44fd5914fb dm: sunxi: Request USB vbus gpio
This is necessary for the device-model enabled builds to work properly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-11-05 13:10:22 +01:00
Ian Campbell
ed41e62f51 sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?I
Mostly automatic with:
    sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05 13:09:58 +01:00
Nobuhiro Iwamatsu
4dc949266d usb: ehci: rmobile: Collect up address data
R8A7791, R8A7793 and R8A7794 have same IP of USB controller.
This collect up address data of each SoCs.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-11-04 06:04:01 +01:00
Nobuhiro Iwamatsu
a3058c08d9 usb: ehci: rmobile: Add support R8A7793
R8A7793 has same IP of USB controller as R8A7791 and R8A7794 of rmobile
ARM SoCs. This adds support R8A7793 to EHCI HCD of rmobile.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-11-04 06:04:01 +01:00
Hans de Goede
8460b89a6d usb: Make pollable int support available outside of ehci-hcd.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04 06:04:00 +01:00
Hans de Goede
8aa26b8e48 usb: ehci: Move cache invalidation to poll_int_queue
Preperation patch to use poll_int_queue outside of ehci-hcd.c .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04 06:04:00 +01:00
Hans de Goede
bd818d81d8 usb: ehci: Move interrupt packet length check to create_int_queue
Preperation patch to use create_int_queue outside of ehci-hcd.c .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04 06:04:00 +01:00
Hans de Goede
32f2eac1e0 usb: ehci: Do not disable an already disabled periodic schedule
When periodic_schedules == 0, the schedule is disabled and there is no reason
to disable it again.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04 06:04:00 +01:00
Tom Rini
5aa7bece10 Merge branch 'master' of git://git.denx.de/u-boot-ti 2014-10-27 09:05:43 -04:00
Tom Rini
1fba907f9a Merge branch 'master' of git://git.denx.de/u-boot-usb 2014-10-26 14:12:18 -04:00
Jeroen Hofstee
2d17b48911 ehci-hcd.c: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:02:00 -04:00
Jeroen Hofstee
3dd80aae3a usb: use __weak
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:02:00 -04:00
WingMan Kwok
bc0e8d7c5d keystone: usb: add support of usb xhci
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Oleksandr Tymoshenko
6e9e06260d usb: dwc2: Add driver for Synopsis DWC2 USB IP block
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.

This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.

Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).

Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Vince Bridgers <vbridger@altera.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2014-10-22 22:01:58 +02:00
Alexandre Courbot
a7f2472224 net: asix: Add support for AX88772B
This USB device works as-is on this driver.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
2014-10-22 22:01:58 +02:00
Albert ARIBAUD
790af81543 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-10-11 01:20:30 +02:00