At present the block device creation happens in the NVMe uclass
driver post_probe() phase. In preparation to support multiple
namespaces, we should issue namespace identify before creating
block devices but that touches the underlying hardware hence it
is not appropriate to do such in the uclass driver post_probe().
Let's move it to driver probe() phase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
AQA (Admin Queue Attributes) register is a dword size with
lower word of ASQS, and higher word of ACQS.
The code set the variable aqa twice, but it is redundant.
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Each prp is 8 bytes, calculate the number of prps
per page should just divide page size by 8
there is no need to minus 1
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
writel() and co. already include the endian swap; doing the swap twice
is, er, unhelpful.
Tested on a P4080DS, which boots perfectly fine off NVMe with this.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom
built from qemu-x86_defconfig no longer boots anymore. Investigation
shows that U-Boot fails at a very early stage during the boot process,
in fdtdec_prepare_fdt() where fdt_check_header() complains that there
is not a valid device tree found at gd->fdt_blob which points to _end.
Now _end points to an allocated section .note.gnu.property which of
course is wrong.
This issue is however not seen when using the default Ubuntu 20.04 gnu
toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows
that it is caused by a behavior change of binutils v2.36 which is part
of the kernel.org gcc 11.1.0 toolchain, via the following commit:
939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")
In fact, there was already a regression bug report [1] for binutils two
months ago, but the binutils folks did not think it is a bug :(
To resolve this, there are several options:
* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script
Linux kernel uses the discard way [2], so let's do the same for U-Boot.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On ARM64 secure OS can run as 64bit or 32bit that's why it is necessary to
record information about architecture that other code can read it and
properly pass it to TF-A and start in 64bit or 32bit mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DT files have been added this year but forgot to update it that's why do it
in separate patch now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Clocking Wizard IP supports clock circuits customized
to your clocking requirements. The wizard support for
dynamically reconfiguring the clocking primitives for
Multiply, Divide, Phase Shift/Offset, or Duty Cycle.
Limited by U-Boot clk uclass without set_phase API, this
patch only provides set_rate to modify the frequency.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP supports also addresses above 4GB (32bit) that's why also
generate u-boot.its with 64bit load/entry addresses to also support
different configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is need to pass entry about secure OS when bl32_entry is defined.
Currently only 64bit support is added but /fit-images node have been
extended to also record if this is 32bit or 64bit secure OS. When this is
tested the code will be update to support this configuration too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The first change is to trying to find out TF-A load address based on
reading elf file. Expectation is that bl31.bin is in the same folder as
bl31.elf. It brings new flexibility to place TF-A to any address (DDR
included).
And also enable TEE generation also with TEE configuration.
Expecation is the same as above that tee.bin and tee.elf are in the same
folder.
User has to just define link to BL31/BL32 binary files and the rest should
be handled by the script.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit 4a1b975dac ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit 1419e5b516 ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
SVDs are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling EFI secure boot which is required for EBBR specification.
Enabling this will fix
"RT.SetVariable - Create one Time Base Auth Variable, the expect return
status should be EFI_SUCCESS"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
