The test adds two pinmux nodes to the device tree, one to test when a
register changes only one pin's mux (pinctrl-single,pins), and the other
to test when more than one pin's mux is changed (pinctrl-single,bits).
This required replacing the controller's register access functions when
the driver is used on sandbox.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
It allows to display the muxing of a given pin. Inspired by more recent
versions of the Linux driver, in addition to the address and the value
of the configuration register I added the pin function retrieved from
the DT. In doing so, the information displayed does not depend on the
platform, being a generic type driver, and it can be useful for debug
purposes.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration of pinmux registers was implemented with duplicate
code which can be removed by adding two functions for read/write access.
Access to 8-bit registers has also been added.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is inspired by more recent versions of the Linux driver.
Replacing the default value 0xffffffff of the function mask with 0 is
certainly more conservative in case the "pinctrl-single,function-mask"
DT property is missing.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
In more recent versions of the Linux kernel the driver's probe function
returns an error if the "pinctrl-single,register-width" DT property is
missing. The lack of this information, in fact, does not allow to know
whether to access the registers of the controller at 8, 16, ... bits.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use dev_read_addr_size to get size of the controller's register area.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The dev_dbg(dev, " reg/val 0x%pa/0x%08x\n", ®, val); prints the 'reg'
address preceded by the prefix 0x0x instead of 0x. This because the
printf '%pa' format specifier already prepends the prefix '0x' to the
address displayed.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The pinmux configuration DT node of a peripheral does not define a
physical address but an offset. Only by adding it to the base address of
the controller it is possible to calculate the physical address of the
register to be configured. Printing an offset also requires a different
formatting option than a physical address.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The 'n' variable is used as a loop counter, not as a physical address,
and is used in a comparison with an int. So it makes sense to change
its type from phys_addr_t to int.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Update the code to use -ENOSYS, which is the correct error code for an
unimplemented system call in U-Boot.
Also we should not check for a missing operations array as this is not
permitted. For now this can be covered by an assert().
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
The EPHY LEDs of mt7629 can be used as JTAG. This patch adds the jtag pin
group to the pinctrl driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mtk pinctrl driver is a combination driver with support for both
pinctrl and gpio. When this driver is used in SPL, gpio support may not be
enabled, and this will result in a compilation error.
To fix this, macros are added to make sure gpio related code will only be
compiled when gpio support is enabled.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This is a bug fix for mtk pinctrl common part. Appearently pins should be
used instead of grps in mtk_get_pin_name().
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Renesas RZ/G2E (a.k.a. r8a774c0) is pin compatible with R-Car
E3 (a.k.a. r8a77990), however it doesn't have several automotive
specific peripherals.
This patch hooks R8A774C0 SoC with the pfc driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Sync the R8A77990 SoC PFC tables with Linux 5.11 , commit f40ddce88593.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
It is convenient to be able to adjust some of the flags for a GPIO while
leaving others alone. Add a function for this.
Update dm_gpio_set_dir_flags() to make use of this.
Also update dm_gpio_set_value() to use this also, since this allows the
open-drain / open-source features to be implemented directly in the
driver, rather than using the uclass workaround.
Update the sandbox tests accordingly. This involves a lot of changes to
dm_test_gpio_opendrain_opensource() since we no-longer have the direciion
being reported differently depending on the open drain/open source flags.
Also update the STM32 drivers to let the uclass handle the active low/high
logic.
Drop the GPIOD_FLAGS_OUTPUT() macro which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is more useful to be able to read all the flags, not just the direction
ones. In fact this is what the STM32 driver does. Update the method name
to reflect this.
Tweak the docs a little and use 'flagsp' as the return argument, as is
common in driver model, to indicate it returns a value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The current method is a misnomer since it is also used (e.g. by stm32) to
update pull settings and open source/open drain.
Rename it and expand the documentation to cover a few more details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Bind only the enabled GPIO subnode, to avoid to probe the node
"gpio-controller" present in SOC dtsi (disabled by default) but
not enabled in the included pincontrol dtsi file.
For example, in stm32mp15xxac-pinctrl.dtsi 2 gpio bank are absent:
gpioj: gpio@5000b000
gpiok: gpio@5000c000
Then these GPIO are absent in output of command "dm tree" and
"gpio status -a"
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
OTYPE can be used for output or for alternate function to select
PP = push-pull or OP = open-drain mode, according reference manual
(Table 81. Port bit configuration table).
This patch removes this indication for input pins and adds it
for AF and output pins for pinmux command output.
Fixes: b305dbc08b ("pinctrl: stm32: display bias information for all pins")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds pinctrl support for MediaTek MT7620 SoC.
The MT7620 SoC supports only pinmux.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Use dev_read_prop instead of using the fdt_read_property which
reads from the GD struct's fdt.
This way the node is accessed via the device config instead of the
global struct, which makes code more portable and GD independent.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
If no GPIO controller is found, the return value should not depend on a
random value on the stack. Initialize variable ret.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Implement get_pin_muxing() callback so that pinmux status
command can be used on Renesas platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
By default on startup all the pin types are configured to
PINMUX_TYPE_NONE (in sh_pfc_map_pins()), when pin is set as GPIO the
pin type is updated to PINMUX_TYPE_GPIO. But the type is not updated
when the pin is set as a function in sh_pfc_pinctrl_pin_set() or
sh_pfc_pinctrl_group_set() calls (these calls only set the MUX if
the pin type is PINMUX_TYPE_NONE ie unused).
So with the current implementation pin functionality could be overwritten
silently, for example if the same pin is added for SPI and serial.
This patch makes sure of updating pin type after every successful call to
sh_pfc_config_mux() and thus fixing from pin functionality to be
overwritten. Also a warning message is printed if the current pin is being
overwritten before abort.
This also avoids pin re-muxing to same type that is for example from
command line device is asked to re-probe/select (mmc dev x) we return
early with success in this case as the pin is already muxed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change debug to log macro and define LOG_CATEGORY.
Remove "%s:" with __func__ as it is managed by log macro
(CONFIG_LOGF_FUNC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
With the new of-platdata, these need to be available to dt_platdata.c
so must be in header files. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
These errors are only really for development purposes. Drop them to reduce
the size of TPL. The error numbers are still reported.
This reduces the TPL binary size on coral by about 160 bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update various drivers to use of_match_ptr() and to avoid including debug
strings in TPL. Omit the WiFi driver entirely, since it is not used in
TPL.
This reduces the TPL binary size by about 608 bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This code was kept around after of-platdata started supporting parent
devices. That feature seems stable now, so let's drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This fixes the wrong usage of clrsetbits_le32(), badly setting the set argument.
Fixes: c4c726c26b ("pinctrl: meson: add pinconf support")
Reported-by: Anton Arapov <arapov@gmail.com>
Reported-by: Otto Meier <gf435@gmx.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not necessary anymore, since device_bind_ofnode() does
the same thing and works with both flattree and livetree.
Rename it to indicate that it is special.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Update pin name to avoid duplicated name with SOC GPIO
gpio0...gpio15 / agpio0....agpio7: add a stmfx prefix.
This pin name can be used in pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The device name is used in pinmux command and in log trace
so it is better to use the parent parent name ("stmfx@42" for
example) than a generic name ("pinctrl" or "stmfx-gpio")
to identify the device instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).
Fixes: da7a0bb1f2 ("pinctrl: stm32: add information on pin configuration")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Drop unused members from struct sh_pfc_pinctrl.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2H and R-Car H3 SoCs.
Optimize pinctrl image size for RZ/G2H, when support for R-Car H3
(R8A7795) is not enabled
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2N and R-Car M3-N SoCs.
Optimize pinctrl image size for RZ/G2N, when support for R-Car M3-N
(R8A77965) is not enabled.
Based on the simialr patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2M and R-Car M3-W/W+ SoCs.
Optimize pinctrl image size for RZ/G2M, when support for R-Car M3-W/W+
(R8A7796[01]) is not enabled.
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
This renames power domains to match the names on the k210 datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
I2C and SCCB previously shared defaults. However, SCCB needs OE_INV and
IE_INV set, but I2C cannot have those bits set. This adds a separate
default for SCCB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
This does not necessarily indicate a problem, since some pins are
optional. Let the caller show an error if necessary.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are a lot of dtoc warnings reported when building
chromebook_coral, of the form:
WARNING: the driver intel_apl_lpc was not found in the driver list
Correct these by using driver names that matches their compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sync the R8A77990 SoC PFC tables with Linux 5.9 , commit bbf5c979011a.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
The AXG pmx driver gpio request offset needs the pin base to have the
correct pin number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl93OLYACgkQ4rK92eCq
k3VQ3ggAlv+e3IXylevdLrCGtoPNb0mC3pB7fKcXedZ7YOHi+ag6MfLKFb3K8UCV
1h8iUX3XpGxOuOzOlqu89UFZBZXkbKP3bPnOJD8AliTEcZN/rTdZK43qYbAVM3tL
UvOtCXMzujmGwJsJqLQmXKK761fpcJFzEisajX+d6cz+at3oMF2Yoa/1RcC8Z7fi
DHWaUME132H5A9pzmt84N83neJNgMmFIDyHBWjNSMkvdiE5jz8MAPFrua8FDyymS
w0QmKmN0ub+5kJqXu4X/LCMZUjYozC3lfNbnwRIkXXKJtQuGEea963bBi7Gastdb
gSCQKmrwjtxa4/g/bpalDTMAvirKnQ==
=Q/62
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201003' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp: DT alignment with Linux 5.9-rc4
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
Currently, the return value of dev_read_u32_default is stored in an u32,
causing the subsequent "if (function < 0)" to always be false:
u32 function;
...
function = dev_read_u32_default(config, "brcm,function", -1);
if (function < 0) {
debug("Failed reading function for pinconfig %s (%d)\n",
config->name, function);
return -EINVAL;
}
Make "function" variable an int to fix this.
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Factor out reading IP base address to ofdata_to_platdata function, which
is designed for this purpose. Also, drop the dev->priv NULL check, since
this is already done by the dm core when allocating space using
priv_auto_alloc_size feature. (in drivers/core/device.c ->
device_ofdata_to_platdata).
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
R8A774A1 is part of Renesas RZ/G2 series and not R-Car, reflect the same
for PINCTRL_PFC_R8A774A1 help description
Alongside, sort the PINCTRL_PFC_R8A774A1 config option as per increasing
number of the SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The GPIO pins used by the SDHCI controller need to be configured to
allow the interface to work.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
Fix this typo in the Kconfig help.
Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the description of devfdt_get_addr_ptr, this function should
return NULL on failure, but currently it returns (void *)FDT_ADDR_T_NONE.
Fix this by making devfdt_get_addr_ptr return NULL on failure, as
described in the function comments. Also, update the drivers currently
checking (void *)FDT_ADDR_T_NONE to check for NULL.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
Continuing with the approach in commit <addf358bac1d2bd0> rename
additional drivers to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
- doc/device-tree-bindings/pinctrl/nexell,s5pxx18-pinctrl.txt added.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
The pins for the MMC controller weren't being set up correctly because the
pinctrl driver only sets the GPIO pullup/pulldown config and doesn't
handle the special cases with PUPD/R0/R1 control.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PFC tables for the R8A774A1 are already available, but they
not enabled.
This patch adds the Kconfig option and builds the corresponding file
when PINCTRL_PFC_R8A774A1 is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
This is in the device tree now, so drop the unnecessary field here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the itss is probed in the ofdata_to_platdata() method. This is
incorrect since itss is a child of p2sb which itself needs to probe the
pinctrl device. This means that p2sb is effectively not probed when the
itss is probed, so we get the wrong register address from p2sb.
Fix this by moving the itss probe to the correct place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add a Kconfig to control whether pinctrl is represented as a single ACPI
device or as multiple devices. In the latter case (the default) we should
return the pin number relative to the pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
At present we can query the offset of a pinctrl register within the p2sb.
For ACPI we need to get the actual address of the register. Add a function
to handle this and rename the old one to more accurately reflect its
purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add information on pin configuration used for pinmux command:
- bias configuration for output (disable, pull up, pull down)
- otype for input (open drain or push pull)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add information on pin configuration used for pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of ops get_dir_flags() to read dir flags from
STMFX registers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the helper functions stmfx_read_reg() and stmfx_write_reg() to avoid
duplicated code for access to stmfx's register with mask.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rename the two function used to change the pin configuration
from stmfx_pinctrl_.. stmfx_conf_... to clarify the function usage.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the functions stmfx_pinctrl_set_pupd and stmfx_pinctrl_set_type;
they can be used by the new ops get_dir_flags and set_dir_flags introduced
by next patch.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
dev_read_addr_ptr had different semantics depending on whether OF_LIVE was
enabled. This patch converts both implementations to return NULL on error,
and converts all call sites which check for FDT_ADDR_T_NONE to check for
NULL instead. This patch also removes the call to map_physmem, since we
have dev_remap_addr* for those semantics.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a pad is not owned by current partition we should not set its
pinmux.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
commit 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
converted pinctrl driver to livetree. In this conversion, the call to
read pinctrl-single,pins/bits property is provided with pinctrl device
pointer instead of pinctrl config pointer. Because of this none of the
pins gets configured. Fix it by passing the right udevice pointer.
Fixes: 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add test for "pins" configuration in gpio uclass with set_state() ops
and test for generic parsing of pinconf_param array).
set_state() is called by:
- pinctrl_generic_set_state
|- pinctrl_generic_set_state_subnode
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add param information in pin information output.
This update prepare unitary test for pin configuration
in pinctrl node.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Migrate pinctrl-generic to livetree:
- dev_for_each_property
- dev_read_prop_by_prop
- dev_read_string_count
- dev_read_string_index
and get rid of DECLARE_GLOBAL_DATA_PTR.
This patch solves the parsing issue during sandbox tests for pin
configuration (OF_LIVE is activated in sandbox_defconfig
and sub node are not correctly parsed in
pinctrl_generic_set_state_subnode with fdt lib API).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert 'pinctrl-single' using livetree functions
- dev_read_prop
- dev_read_u32_default
- dev_read_u32_array
- dev_read_bool
- dev_read_addr
and get rid of DECLARE_GLOBAL_DATA_PTR.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use int as result of dm_i2c_reg_read to avoid warning with
W=1 (warning: comparison is always false due to limited range
of data type [-Wtype-limits])
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Add an IRQ type to each driver and use irq_first_device_type() to find
and probe the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The code in this file is not specific to Apollo Lake. According to
coreboot sources (where this code comes from), it is common to at least:
* Apollo Lake
* Cannon Lake
* Ice Lake
* Skylake
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Due to the pinctrl hardware of MT7622 is difference from others
SoC which using the common part of mediatek pinctrl.
So we need to modify the common part of mediatek pinctrl.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Add a driver for the Apollo Lake pinctrl. This mostly makes use of the
common Intel pinctrl support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Recent Intel SoCs share a pinctrl mechanism with many common elements. Add
an implementation of this core functionality, allowing SoC-specific
drivers to avoid adding common code.
As well as a pinctrl driver this provides a GPIO driver based on the same
code.
Once other SoCs use this driver we may consider moving more properties to
the device tree (e.g. the community info and pad definitions).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these options cannot be enabled for SPL/TPL, but this can be
useful in some cases. Add Kconfig options to allow it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
An iomux register contains 8 pins, each of which is represented
by 2 bits, but the register offset is 0x8.
For example, GRF_GPIO0A_IOMUX offset is 0x0, but GRF_GPIO0B_IOMUX
offset is 0x8, the offset 0x4 is reserved.
So add a type IOMUX_8WIDTH_2BIT to calculate offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi 4 upstream kernel device tree instroduces
a new compatible for the pinctroller. Add this to the driver
so that we can boot with the upstream kernel DT.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
Add the necessary glue code to allow pinctrl setting on px30 socs.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the pinctrl_decode_pin_config() API, because this
function is unused and not compatible with livetree
(it uses fdtdec_get_bool instead of ofnode API).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit e878b53a79 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit c20851b3d8 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixed CONFIG_IF_ENABLED() condition, added __maybe_unused:
Signed-off-by: Simon Glass <sjg@chromium.org>
Skip not associated gpio phandle let register the other gpios on a group.
We need anyway to send out a warning to the user to fix their uboot-board.dtsi.
Thhe handle id can be found inside the decompiled dtb
dtc -I dtb -O dts -o devicetree.dts spl/u-boot-spl.dtb
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For NXP SoCs we have to set pinmux configuration ASAP (ideally
before relocation) to get serial console working. Without this we miss
almost the half of output (U-boot version, CPU defails, Reset cause,
DRAM details etc.).
To achieve this we need to force appropriate pinctrl drivers to get
probed before relocation.
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Alignment with kernel driver.
According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinctrl_conf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1 | 0 | 0/1 | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0 | 1 | 1 | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0 | 1 | 0 | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0 | 0 | 1 | INPUT floating
----|------|------|---------------------------------------------------
0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Fix the following warning when CONFIG_PINCONF=n:
drivers/pinctrl/mediatek/pinctrl-mtk-common.c:35:36:
warning: ‘mtk_drive’ defined but not used [-Wunused-const-variable=]
static const struct mtk_drive_desc mtk_drive[] = {
^~~~~~~~~
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Fix GPIO bank 0 pin 0 request/release off by one error. Without this
patch, it is not possible to request/release GPIO bank 0 pin 0.
Signed-off-by: Tiezhuang Dong <tiezhuang.dong.yh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
In spite of the summary line, U-Boot commits [1-2] seem to have
aligned the U-Boot PFC tables to Linux v5.1 rather than to v5.0, since
they also imported the Linux 5.1 commits listed in [3].
What current commit tries to accomplish is to align the Gen2 and Gen3
pinctrl tables to Linux v5.2. Importing these updates in two steps
as done before (i.e. separately for Gen2 and Gen3) is somewhat difficult
due to Linux commits like [5-6] which atomically update both Gen2/3
platforms and whose breakdown would not be easily possible.
The detailed list of Linux commits squashed into this U-Boot patch is
shown in [4]. The second column in [4] depicts the patch id mismatch
between the original Linux and the resulted U-Boot commit. The
exclamation mark means that manual conflict resolution was involved
during cherry picking Linux commit into U-Boot repository (this is
mainly caused by dropped changes in files like pfc-r8a7795-es1.c and
pfc-r8a77980.c which are missing in U-Boot).
This patch has been applied on top of v2019.07-rc4-155-g8754656680b6 and
boot-tested on:
- H3-ES2.0-Salvator-X
- M3-ES1.1-Salvator-XS
- M3N-ES1.1-ULCB
[1] 8719ca8113 ("pinctrl: renesas: Synchronize Gen3 tables with Linux 5.0")
[2] a6a743df24 ("pinctrl: renesas: Synchronize Gen2 tables with Linux 5.0")
[3] Linux 5.1 commits already contained in [1-2]:
79dbbdbeccc6784 pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
729257d674bc2e6 pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
b9fd50488b4939c pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
a4b0350047f1b10 pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
fdbbd6b74c9278f pinctrl: sh-pfc: r8a77990: Add DRIF pins, groups and functions
16978e7d40f73be pinctrl: sh-pfc: r8a77990: Add TMU pins, groups and functions
86c045c2e4201e9 pinctrl: sh-pfc: r8a77965: Replace DU_DOTCLKIN2 by DU_DOTCLKIN3
b8ba194ca5f4ca2 pinctrl: sh-pfc: r8a7791: Fix VIN1 versioned groups
81c585c96b7dd47 pinctrl: sh-pfc: r8a77970: Deduplicate VIN[01] pin definitions
08b7e2112a9b19c pinctrl: sh-pfc: r8a7796: Deduplicate VIN5 pin definitions
99fdb920f5534d1 pinctrl: sh-pfc: r8a7795: Deduplicate VIN5 pin definitions
85ccae133bde425 Revert "pinctrl: sh-pfc: r8a77990: Add support for pull-up only pins"
f7d8b568e204d29 pinctrl: sh-pfc: r8a77990: GP6_9 does not have pull-down capability
5219aa33caec2f7 pinctrl: sh-pfc: r8a77995: Fix MOD_SEL bit numbering
3e3eebeacad79bd pinctrl: sh-pfc: r8a77990: Fix MOD_SEL bit numbering
7219a4b64520873 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit2 when using RX2, TX2 and SCK2
699c7d1346fbef6 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit3 when using TX0
[4] Linux 5.2 commits backported and squashed into this U-Boot patch
Linux commit id Linux commit summary line
9925e8795726801 pinctrl: sh-pfc: Validate pins/marks in pin groups at build time
f83f97684a737f6 pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
5e8588c86d71e78 pinctrl: sh-pfc: Validate fixed-size field widths at build time
1c5c1101755c5ed pinctrl: sh-pfc: r8a77970: Rename IOCTRLx registers
3df892fdbfe6919 pinctrl: sh-pfc: r8a77990: Rename IOCTRLx registers
dcd24e098d8df8b pinctrl: sh-pfc: r8a7796: Move CANFD pin groups and functions
2cee6cb290ab30f pinctrl: sh-pfc: r8a77990: Move CANFD pin groups and functions
d92ee9cf8ec8d7f ! pinctrl: sh-pfc: rcar-gen3: Retain TDSELCTRL register across suspend/resume
efca8da0c5fcc7f ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG() macro
69f7be1c6314fb0 ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG_VAR() macro
19b593a1cf068ef ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_DATA_REG() macro
c481c8178420b8c pinctrl: sh-pfc: Validate enum IDs for regs with fixed-width fields
fa4d36712f20e24 ! pinctrl: sh-pfc: Validate enum IDs for regs with variable-width fields
360328c7dc15f48 pinctrl: sh-pfc: Improve PINMUX_IPSR_PHYS() documentation
943ff71281c6ce4 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit16 when using NFALE and NFRB_N
e167d723e1a472d pinctrl: sh-pfc: r8a77990: Fix MOD_SEL1 bit31 when using SIM0_D
e87882eb9be10b2 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL1 bit30 when using SSI_SCK2 and SSI_WS2
5671f8e0270ad5e ! pinctrl: sh-pfc: rcar-gen3: Remove HDMI CEC pins, groups, and functions
662dc924a05e9df ! pinctrl: sh-pfc: rcar-gen3: Remove CC5_OSCOUT pin
624a7a12cc0cc77 ! pinctrl: sh-pfc: rcar-gen3: Rename RTS{0,1,3,4}# pin function definitions
a040f3dec8eb7b1 pinctrl: sh-pfc: rcar-gen3: Rename SEL_ADG_{A,B,C} to SEL_ADG{A,B,C}
e551122cdb7fcb9 pinctrl: sh-pfc: rcar-gen3: Rename SEL_NDFC to SEL_NDF
baaa2effc684e49 pinctrl: sh-pfc: r8a77970: Fix spacing
f05603fa6aa3043 pinctrl: sh-pfc: r8a7796: Remove placeholder I2C pin data
0a042b355e60269 pinctrl: sh-pfc: r8a77965: Add I2C{0,3,5} pins, groups and functions
[5] efca8da0c5fcc7 ("pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG() macro")
[6] 69f7be1c6314fb ("pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG_VAR() macro")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
The code responsible for setting proper values in the MUX registers
(in the mxs_pinctrl_set_state()) has been ported from Linux kernel
- SHA1: 17bb763e7eaf tag v5.1.11 from linux-stable.
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes,
it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also
make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals. This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update .bind callback in order to bind all pinctrl subnodes
with "gpio-controller" property to gpio_stm32 driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (*idx < 0)
^
drivers/pinctrl/pinctrl_stm32.c: At top level:
warning: no previous prototype for 'stm32_pinctrl_probe' [-Wmissing-prototypes]
int stm32_pinctrl_probe(struct udevice *dev)
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QA+5
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogic
- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).
This fixes HDMI support for GXBB in u-boot.
Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the AXG specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the GX specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
In order to support the "pinmux status" command, add common function
to get pins count and pin name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO
groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_*
group names were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.
The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).
This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Only some Soc need Schmitter feature, so move the
implementation into their own files.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the mux/pull/drive feature implement at own file,
the type and label are not necessary.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3288 pmu_gpio0 pull setting have no higher 16 writing corresponding
bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3288 pmu_gpio0 drive strength setting have no higher 16 writing
corresponding bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
