The following boards gain device tree support with this patch:
ca9x4_ct_vxp - Versatile Express
i.mx5 boards:
efikamx
mx51evk
mx53evk
OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430
Tegra boards:
Harmony
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Most OMAP3 boards have various flash related macros in their configs
that are either not referenced anywhere in the code or are used by
drivers that are not enabled. Remove them.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch fixes the issue by defining and using CONFIG_SYS_INIT_RAM_SIZE and
CONFIG_SYS_INIT_RAM_ADDR. Based on an email discussion with Wolfgang Denk and
Heiko Schocher.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Overo expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents. It prints
the expansion board name and revision and modifies environment variables
as appropriate.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Future versions of these boards have options for POP memory with no NAND.
This option prevents display of error messages when no NAND is detected.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Allows one to set the processor clock rate via "setenv mpurate 720" for example
Default is set to a "safe" 500 Mhz.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9
Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.
The two architectures are similar enough that substantial code can be shared.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Every omap3 board config file declared the global variable gpmc_cfg.
This changes moves the declaration to a better location in the
arch dependent header file cpu.h.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
A number of config files define the V_PROMPT macro for the
command-line prompt, only to immediately use that macro to define
CONFIG_SYS_PROMPT, making V_PROMPT entirely superfluous.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.
Signed-off-by: Heiko Schocher <hs@denx.de>
Update default environment to support new kernel DSS2 subsystem and
simplify rootfs type and location changes.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.
These functions reuse content from the existing function
display_board_info() - which has been removed.
Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Sanjeev Premi <premi@ti.com>
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Divisor field is called PTV not PVT.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
