In order to be able to build the Rockchip eMMC driver on rv1108, the
BOUNCE_BUFFER option needs to be selected. Select it like it is done
on the other Rockchip SoC common files.
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
The RK3188 rock board does not need TPL: remove TPL_TINY_MEMSET from
config.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up commit message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 SPL has two cases that may end in a hard-stop: if either
the pinctrl can not be initialised or if the DRAM fails to initialise.
Both have previously not triggered an error message unless DEBUG was
defined (i.e. both used debug() to print the error).
This converts both error messages to be printed using pr_err() to
ensure that some output points to the cause of the hard-stop.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was an incorrect check when looping and finding the first
fast enough frequency in the freq_rang table. The code did
actually return the first that was either exactly correct or
too slow.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was a copy and paste error where the data
enable setting was written to the version register.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions
into pinctrl-driver") moved the iomux settings out of the grf header
to prevent conflicts with the iomux definitions of other rockchip socs.
This also breaks the early uart setup, as the iomux for uart2 are needed.
To fix that just put the tiny amount of needed iomux definitions next to
the early uart code.
Fixes: 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions into pinctrl-driver")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip socs can route the debug uart pins through the d+ and d- pins
of one specific usbphy per soc. Add a config option and implement the
setting on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up to mark grf as maybe unused:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch prevents disabling the FPGA bridges when
SPL or U-Boot is executed from FPGA onchip RAM.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As a preparation for merging the socfpga gen5 devicetree files
from Linux, this patch makes the dwapb gpio driver work correctly
without the 'bank-name' property on the gpio-controller nodes.
This property is not present in the Linux drivers and thus is not
present in the Linux devicetrees. It is only used to access pins
via bank name.
This fallback is necessary since without it, the driver will
return an error code which will lead to an error in U-Boot
startup.
The bank names will still be added to the default board device
trees in follow-up patch, but other boards using this driver and
not including the bank name should also work with the socfpga.dtsi
without adding the bank-name property.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add a few notes on how to try out the MediaTek support so far.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a DDR3 driver for MT7629 SoC.
Signed-off-by: Wu Zou <wu.zou@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many SoCs from MediaTek have a high-speed uart. This UART is compatible
with the ns16550 in legacy mode. It has extra registers for high-speed
mode which can reach a maximum baudrate at 921600.
However this UART will no longer be compatible if it's in high-speed mode.
Some BootROM of MediaTek's SoCs will change the UART into high-speed mode
and the U-Boot must use this driver to initialize the UART.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7623 SoC. And most of the
structures are used to hold the hardware configuration for each
pin.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a common driver for the Mediatek SoC integrated
watchdog.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock source and clock event for the timer found
on the Mediatek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a driver for MT7623 clock blocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock modules for MediaTek SoCs:
- Shared part: a common driver which contains the general operations
for plls, muxes, dividers and gates so that we can reuse it in future.
- Specific SoC part: the group of structures used to hold the hardware
configuration for each SoC.
We take MT7629 as an example to demonstrate how to implement driver if
any other MediaTek chips would like to use it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7623 SoCs from MediaTek.
As this u-boot is loaded by MTK proprietary preloader, there is no
low level initializtion codes.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for MTK boot image generation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DM_SERIAL is selected by TARGET_CHILIBOARD, so there is no reason to
keep code that will not be built. Remove it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove ethernet platform data, as all
details are in device-tree now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option is defined by a few boards but doesn't guard any code.
Remove it from the boards and config_whitelist.txt.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allow for convenient use of QEMU machine to test loading of UBI
filesystem. There are a couple of changes made together of this which
are required:
1) The malloc must be at least 512 KiB to allow the use of UBI
filesystem. We are going to enable it in a next patch.
2) MTD_DEVICE must be enabled, otherwise we get missing symbols
during the build
Following configs were change:
- vexpress_aemv8a_dram_defconfig
- vexpress_aemv8a_juno_defconfig
- vexpress_aemv8a_semi_defconfig
- vexpress_ca15_tc2_defconfig
- vexpress_ca5x2_defconfig
- vexpress_ca9x4_defconfig
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
When the spi_flash_probe_bus_cs() was previously called, it was
called using 0's for two values where CONFIG_ENV_SPI_MAX_HZ and
CONFIG_ENV_SPI_MODE are now used. When changed this
caused the environment to fail the CRC check and the default
was used. This patch defines both of these values back 0.
Fixes: 25a17652c9 ("fix: env: Fix the SPI flash device setup
for DM mode")
Signed-off-by: Adam Ford <aford173@gmail.com>
Some erratum workarounds call into C code before the stack
is setup, this can lead to values pushed onto the stack
being lost, firewall exceptions, and other undefined behavior.
Setup a temporary stack to allow these functions to work
correctly.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
stdlib.h is the header for malloc since at least c89/c90.
Previously this would fail to build on OpenBSD and fallback to the wrong
header:
In file included from u-boot/tools/file2include.c:21:
u-boot/include/malloc.h:875:5: error: function-like macro
'CONFIG_IS_ENABLED' is not defined
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Recent removal of obsolete partition led to shifting of starting address
of "reserved" partition (which reflects U-Boot environment). Fix its
start address to keep it in sync with ENV_OFFSET and DFU environment.
This patch also provides fixed start address for "reserved" partition,
so that we can track when it's shifted next time.
While at it, move it before "misc" partition to keep all Android
partitions together.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-By: Praneeth Bajjuri <praneeth@ti.com>
Based on the MCU R5 efuse settings, R5F cores in MCU domain
either work in split mode or in lock step mode.
If efuse settings are in lockstep mode: ROM release R5 cores
and SPL continues to run on the R5 core is lockstep mode.
If efuse settings are in split mode: ROM releases both the R5
cores simultaneously and allow SPL to run on both the cores.
In this case it is bootloader's responsibility to detect core
1 and park it. Else both the core will be running bootloader
independently which might result in an unexpected behaviour.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
with this patch the selected Entry in bootmenu can be set by
environment-var bootmenu_default=<number>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
